3M X45 (01) PDF MANUAL

Report any errors on this page in the comment box below.


PDF Content Summary: S55/X45/X55 Multimedia Projector Operator's Guide Thank you for purchasing this projector. CAUTION ►Before using, read the "Product Safety Guide" and these manuals to ensure correct usage through understanding. After reading, store them in a safe place for future reference. About this manual Various symbols are used in this manual. The meanings of these symbols are described below. WARNING This symbol indicates information that , if ignored, could possibly result in personal injury or even death due to incorrect handling. CAUTION This symbol indicates information that , if ignored, could result possibly in personal injury or physical damage due to incorrect handling. ffl Please refer to the pages written following this symbol. NOTE • The information in this manual is subject to chance without notice. • The manufacture assumes no responsibility for any errors that may appear in this manual. • The reproduction, transmission or use of this document or contents is not permitted without express written authority. Trademark acknowledgment • VGA and XGA are registered trademarks of the International Business Machines Corporation. • Apple and Mac are registered trademarks of the Apple Computer, Inc. • VESA and SVGA are trademarks of the Video Electronics Standard Association. • Windows is a registered trademark of the Microsoft Corporation. • Internet Explorer is a trademark of the Microsoft Corporation. All other trademarks are the property of their respective owners. 1 Contents Contents ffl ffl About this manual . . . . . . . . . . 1 EASY Menu . . . . . . . . . . . . . . . . . . 24 Contents . . . . . . . . . . . . . . . . . 2 Projector features . . . . . . . . . . 3 Aspect, Keystone, Mode, Bright, Contrast, Color, Tint, Sharpness, Whisper, Mirror, Reset, Filter time, Preparations . . . . . . . . . . . . . . 3 Language, Go to advanced menu Part names . . . . . . . . . . . . . . . 4 PICTURE Menu . . . . . . . . . . . . . . . 26 Projector . . . . . . . . . . . . . . . . . . . . . 4 Bright, Contrast, Gamma, Color temp, Controls . . . . . . . . . . . . . . . . . . . . . . 5 Color, Tint, Sharpness, Progressive, Remote control . . . . . . . . . . . . . . . . 5 My memory Setting up . . . . . . . . . . . . . . . . 6 IMAGE Menu . . . . . . . . . . . . . . . . . 29 Arrangement . . . . . . . . . . . . . . . . . . 7 Aspect, Over scan, V. position, H. Adjusting the projector's elevator . . 8 position, H. phase, H. size, Auto adjust Attaching the base . . . . . . . . . . . . . . 9 INPUT Menu . . . . . . . . . . . . . . . . . 31 About the filter cover for bottom-up use . 10 Color space, Component, Video format, Connecting your devices . . . . . . . . .11 Frame lock, Information Connecting power supply . . . . . . . 14 SETUP Menu . . . . . . . . . . . . . . . . . 33 Remote control . . . . . . . . . . . 15 Keystone, Whisper, Mirror, Volume Putting batteries . . . . . . . . . . . . . . 15 Using the remote control . . . . . . . . 16 SCREEN Menu . . . . . . . . . . . . . . . 34 Language, Menu position, OSD bright, Power on/off . . . . . . . . . . . . . 17 Turning on the power . . . . . . . . . . . 17 Blank, Start up, MyScreen, MyScreen lock, Message Turning off the power . . . . . . . . . . . 17 OPTION Menu . . . . . . . . . . . . . . . . 37 Operating . . . . . . . . . . . . . . . 18 Adjusting the volume . . . . . . . . . . . 18 Temporarily muting the sound . . . . 18 Search, Auto off, Lamp time, Filter time, Service Maintenance . . . . . . . . . . . . . 39 Selecting an input signal . . . . . . . . 18 Searching an input signal . . . . . . . 19 Selecting the aspect ratio . . . . . . . 19 Lamp . . . . . . . . . . . . . . . . . . . . . . . 39 Air filter . . . . . . . . . . . . . . . . . . . . . 41 Other care . . . . . . . . . . . . . . . . . . . 42 Adjusting the zoom and focus . . . . 19 Using the automatic adjustment feature . 20 Troubleshooting . . . . . . . . . . 43 Related messages . . . . . . . . . . . . . 43 Adjusting the position . . . . . . . . . . 20 Correcting the keystone distortions 20 Using the magnify feature . . . . . . . 21 Freezing the screen . . . . . . . . . . . . 21 Temporarily blanking the screen . . 21 Operating the computer screen . . . 22 Regarding the indicator lamps . . . . 45 Phenomena that may easily be mistaken for machine defects . . . . 47 Specifications . . . . . . . . . . . . 49 Accessories . . . . . . . . . . . . . . 51 Multifunctional settings . . . . 23 Using the menu function . . . . . . . . 23 2 Projector features / Preparations Projector features This projector is used to project various computer signals as well as NTSC / PAL / SECAM video signals onto a screen. It requires just a little space for installation and gets a large image from short distance. ❍ High Brightness Newly developed 165W UHB (Ultra High Brightness) lamp gives you a higher brightness image on a screen. The image can be still kept as bright and clean enough for use in bright rooms. ❍ Low Noise WHISPER mode is equipped for reducing acoustic noise to realize quieter operation. It is perfect for use in low luminance rooms where low noise is more important than brightness. ❍ Rich Connectivity This projector has a variety of I/O ports. It can be easily connected to many signal sources like PC, DVD and so on. The rich connectivity provides you more options to make your presentation impressive. ❍ Compact Body Even with its many features, this projector is extremely compact and slim, which gives you more flexibility and usability to use it where you want. Preparations About contents of package Your projector should come with the items shown below. Contact immediately your dealer if anything is missing. NOTE • Keep the original packing materials for future reshipment. For moving the projector, be sure to use the original packing material. Use special caution for the lens part. Operator's Guide Product SafetyGuide Quick Start Guide Warranty ????? ??? ?????? ?????? ???? ????? ??????? ???? ??????? ?????? ?? ??? ??????? ?????? ????????? ????? ??? ???????? ???? ????? Projector ??? ????? Remote control (with two AA batteries) ?????????? Power cord (US, UK, EUROPE) Filter cover bottom-up use VGA cable Soft case Base 3 4Part names Part names Projector Remote sensor (ffl16) Zoom knob (ffl19) Speaker Focus ring (ffl19) Vent (ffl6) Elevator button (ffl8) Lens (ffl17) Front-Right side Elevator foot (ffl8) Lamp door (Lamp unit is inside.) (ffl39) Filter cover (ffl41) (Air filter and intake vent are inside.) Bottom side Power switch (ffl17) Control buttons (See the following page.) AC inlet (ffl14) (ffl5)Elevator button (ffl8) Ports (See below.) Elevator foot (ffl8) Vent (ffl6) Rear-Left side AUDIO OUT port (ffl12) COMPONENT VIDEO ports (ffl13) YCB/PB CR/PR Ports NOTE () About Restart switch: This Projector is controlled by an internal microprocessor. Under certain exceptional circumstances, the projector may not operate correctly and the microprocessor will need to be reset. In such a case, please push the Restart switch by using a cocktail stick or similar and before turning on again, make the projector cool down at least 10 minutes without operating. Only push the Restart switch in these exceptional instances. Restart switch () (ffl47) AUDIO IN1 port (ffl12) RGB IN1 port (ffl12) S-VIDEO port (ffl13) RGB IN2 port (ffl12) RGB OUT port (ffl12) Kensington lock slot VIDEO port (ffl13) AUDIO IN2 port (ffl12) USB port (ffl22) CONTROL port (ffl12) S-video component videoCB/PB CR/PR Y video audio in1 audio out rgb in1 USB control rgb in2 rgb out audio in2 Part names Control buttons LAMP indicator (ffl45) TEMP indicator (ffl45) lamp POWER indicator (ffl17) temp STANDBY/ON button (ffl17) menu VIDEO RGB SEARCH Cursor buttons ▲,▼,◄,► (ffl23) INPUT button (ffl18) Remote control RGB button (ffl18) VIDEO button (ffl18) ASPECT button (ffl19) HOME button (ffl22) MAGNIFY (ffl21) ON button OFF button END button (ffl22) FREEZE button (ffl21) POSITION button (ffl20) Cursor buttons ▲,▼,◄,►(ffl23) ESC button (ffl23) power SEARCH button (ffl19) STANDBY/ON STANDBY/ON button (ffl17) AUTO button (ffl20) ASPECT AUTO BLANK BLANK button (ffl21) MAGNIFY HOME PAGE UP VOLUME ON VOLUME button (ffl18) OFF END PAGE DOWN MUTE PAGE UP button (ffl22) FREEZE KEYSTONE MUTE button (ffl18) PAGE DOWN button (ffl22) POSITION MENU KEYSTONE button (ffl20) ENTER MENU button (ffl23) ESC RESET ENTER button (ffl23) RESET button (ffl23) 5 6Setting up Setting up WARNING ►Place the projector in a stable position horizontally. A fall or a turnover could cause an injury and/or damage to the projector. Then using damaged projector could result in a fire and/or an electric shock. • Don’t place the projector on an unstable, slant or vibrant surface such as a wobbly or inclined stand. • Do not place the projector in the side/front/rear-up position, except care of the air filter. • For the projector installed bottom-up, use the accessory filter cover for bottom- up use. And in the case of a ceiling installation or the like, contact your dealer before installation. ►Place the projection in a cool place, and pay attention enough to ventilation. The high temperature of the projector could cause a fire, a burn and/or malfunction to the projector. • Don’t stop up, block and cover the projector's vents. • Keep a space of 30 cm or more between the sides and other objects such as walls. • Don’t place the projector on a metallic thing or anything weak in heat. • Don’t place the projector on a carpet, cushion or bedding. • Don’t place the projector in direct sunlight or near a hot object such as heater. • Put nothing about lens and vents of the projector. Put nothing on the projector. • Put nothing that is sucked or sticks to the bottom of projector. This projector has some intake vents also on the bottom. ►Do not place the projector on the place that gets wet. Damping the projector or inserting liquid in the projector could cause a fire, an electric shock and/or malfunction to the projector. • Don’t place the projector in a bathroom or the outdoors. • Put nothing containing the liquid near the projector. CAUTION ►Avoid a smoky, humid or dusty place. Placing the projector in such place could cause a fire, an electric shock and/or malfunction to the projector. • Don’t place the projector near a humidifier, a smoking space or a kitchen. • Put nothing containing the liquid near the projector. ►Adjust the direction of the projector to keep light from directly hitting the projector's remote sensor. Setting up Arrangement Refer to the illustrations and tables below to determine the screen size and projection distance. The values shown in the table are calculated for a full size screen (S55: 800x600 pixels, X45/X55: 1024x768 pixels). (a) The screen size (diagonal) (b) Distance from the projector to the screen (±10%) (c) The height of the screen (±10%) At 16:9 screen (b) 4:3 16:9 (c) up (a) (a) (c) down At 4:3 screen (a) Screen size [inch (m)] (b) Projection distance [m (inch)] (c) Screen height [cm (inch)] min. max. down up 30 (0.8) 0.9 (35) 1.1 (42) 5 (2) 41 (16) 40 (1.0) 1.2 (47) 1.4 (56) 6 (2) 55 (22) 50 (1.3) 1.5 (59) 1.8 (71) 8 (3) 69 (27) 60 (1.5) 1.8 (72) 2.2 (85) 9 (4) 82 (32) 70 (1.8) 2.1 (84) 2.5 (100) 11 (4) 96 (38) 80 (2.0) 2.4 (96) 2.9 (114) 12 (5) 110 (43) 90 (2.3) 2.7 (108) 3.3 (129) 14 (5) 123 (49) 100 (2.5) 3.1 (120) 3.6 (143) 15 (6) 137 (54) 120 (3.0) 3.7 (144) 4.4 (172) 18 (7) 165 (65) 150 (3.8) 4.6 (181) 5.5 (216) 23 (9) 206 (81) 200 (5.1) 6.1 (242) 7.3 (288) 30 (12) 274 (108) 250 (6.4) 7.6 (303) 9.2 (361) 38 (15) 343 (135) 300 (7.6) 9.2 (363) 11.0 (433) 46 (18) 411 (162) (a) Screen size [inch (m)] (b) Projection distance [m (inch)] (c) Screen height [cm (inch)] min. max. down up 30 (0.8) 1.0 (38) 1.2 (46) -1 (0) 39 (15) 40 (1.0) 1.3 (52) 1.6 (62) -2 (-1) 51 (20) 50 (1.3) 1.6 (65) 2.0 (77) -2 (-1) 64 (25) 60 (1.5) 2.0 (78) 2.4 (93) -2 (-1) 77 (30) 70 (1.8) 2.3 (91) 2.8 (109) -3 (-1) 90 (35) 80 (2.0) 2.7 (105) 3.2 (125) -3 (-1) 103 (41) 90 (2.3) 3.0 (118) 3.6 (140) -4 (-1) 116 (46) 100 (2.5) 3.3 (131) 4.0 (156) -4 (-2) 129 (51) 120 (3.0) 4.0 (158) 4.8 (188) -5 (-2) 154 (61) 150 (3.8) 5.0 (197) 6.0 (235) -6 (-2) 193 (76) 200 (5.1) 6.7 (264) 8.0 (314) -8 (-3) 257 (101) 250 (6.4) 8.4 (330) 10.0 (393) -10 (-4) 322 (127) 300 (7.6) 10.1 (396) 12.0 (472) -12 (-5) 386 (152) 7 8Adjusting the projector's elevator WARNING ►Do not adjust the projector’s elevator during use or immediately after use. Handling while the projector is in a high temperature could cause a burn and/or malfunction to the projector. CAUTION ►If you press the elevator button without holding the projector, the projector might crash down, overturn, smash your fingers and possibly result in malfunction. To prevent damaging the projector and injuring yourself, always hold the projector whenever using the elevator buttons to adjust the elevator feet. ►Except for inclining by the elevator feet adjustment, place the projector horizontally. You can use the elevator feet to make adjustments if the surface on which you need to set the projector is uneven or if you otherwise need to adjust the angle of projection. The adjustment range of the elevator feet is 0 to 9 degrees. 1. After making sure that the projector is cool adequately, press and hold in the elevator buttons while holding the projector. The elevator buttons and the elevator feet are on the both sides. 2. Raise or lower the projector to the desired height and the release the elevator buttons. When you release the elevator buttons, the elevator feet will lock into position. 3. As necessary, you can also finely adjust the height of the projector by twisting the elevator feet by hand. Setting up Elevator feet Elevator button Setting up Adjusting the projector's elevator CAUTION ►Be careful not to pinch your finger on the occasion of the handling of a base. ►Do not hold the base, lens or other project part to move the projector. ►Do not use the base to suspend the projector. ►Do not push or put anything on the both sides of the top of the projector. Bottom of the Lever Base projector Front 1. Turn for at off least the 45minutes. projector, and unplug the power cord. Allow the lamp bulb to cool 2. After projector, make so sure that that the the bottom projector is facing has up. cooled adequately, slowly flip over the 3. Put it to the the base front on of the the projector bottom of until the it projector locks into as position. shown in To the remove figure. it, Then slide slide the base to the back of the projector pinching the lever of the base. 4. Slowly turn the projector so that the top is facing up. 9 10Setting up About the filter cover for bottom-up use WARNING ►Do not replace the filter cover during use or immediately after use. While the projector connects with a power supply, or the projector is in a high temperature state, handling could cause an electric shock, a fire, a burn and/or malfunction to the projector.Before handling, make sure the power switch is off and the power cord is not plugged in, then wait at least 45 minutes. When the projector is installed bottom up, please use the accessory filter cover for bottom-up use. It is higher than usual filter cover, to keep the space for intake ventilation. Please change in the following procedure. To remove 1. After projector making so that sure the that lens-side the projector is facing is cool up. adequately, slowly turn the Please be careful for a projector not to fall. While the projector is placed lens-side up, hold the projector. 2. Please similar, To set Filter cover’s claw unhook the claw of the filter cover using a minus screwdriver or and remove the filter cover. 3. Replace the filter cover for bottom-up use and snap it back into place. 4. Slowly turn the projector so that the top is facing up. Filter cover’s claw Filter cover Filter cover for bottom-up use Setting up Connecting your devices CAUTION ►Turn off all devices prior to connecting them to the projector. Attempting to connect a live device to the projector may generate extremely loud noises or other abnormalities that may result in malfunction and/or damage to the device and/or projector. ►Use the accessory cable or a designated-type cable for the connection. Some cables have to be used with core set. A too long cable may cause a certain picture degradation. Please consult with your dealer for details. For cables that have a core only at one end, connect the core to the projector. ►Make sure that you connect devices to the correct port. Incorrect connection may result in malfunction and/or damage to the device and/or projector. NOTE • Whenever attempting to connect a laptop computer to the projector, be sure to activate the laptop’s RGB external image output (set the laptop to CRT display or to simultaneous LCD and CRT display). For details on how this is done, please refer to the instruction manual of the corresponding laptop computer. • Secure the screws on the connectors and tighten. • Some computers may have multiple display screen modes. Use of some of these modes will not be possible with this projector. • For some RGB signal modes, the optional Mac adapter is necessary. • When the image resolution is changed on a computer, depending on an input, automatic adjust function may take some time and may not be completed. In this case, you may not be able to see a check box to select “Yes/No” for the new resolution on Windows. Then the resolution will go back to the original. It might be recommended to use other CRT or LCD monitors to change the resolution. About Plug-and-Play capability Plug-and-Play is a system composed of the computer, its operating system and peripheral equipment (i.e. display devices). This projector is compatible with VESA DDC 2B. Plug-and-Play can be achieved by connecting this projector to computers that are VESA DDC (display data channel) compatible. • Please take advantage of this function by connecting the accessory RGB cable to the RGB IN1 port (DDC 2B compatible). Plug-and-Play may not work properly if any other type of connection is attempted. • Please use the standard drivers in your computer as this projector is a Plug-and-Play monitor. 11 Examples of connection with a computer RGB cable Stereo mini audio cable Connecting to a monitor (output) Connecting to a speaker with amplifier (output) 12 Setting up RGB out RS-232C Audio out USB(A) AUDIO IN1 is linked to RGB IN1. audio in1 Y rgb in1 video CONTROL RGB out Audio out Stereo mini audio cable RGB cable RGB in RGB cable Audio in Stereo mini audio cable audio out usb rgb in2 rgb out CB/PB audio in2 CR/PR S-video component videoUSB RS-232C cable cable audio in1 Y audio out rgb in1 video usb control RGB IN2 rgb out CB/PB audio in2 CR/PR S-video component videoaudio in1 Y audio out rgb in1 video usb control rgb in2 RGB OUT CB/PB audio in2 CR/PR S-video component videoaudio in1 Y audio out rgb in1 video USB control rgb in2 rgb out CB/PB audio in2 CR/PR S-video component video Setting up Examples of connection with a VCR/DVD player audio in1 Audio out Video out Y audio out rgb in1 VIDEO usb control Stereo mini audio cable rgb in2 rgb out CB/PB audio in2 CR/PR S-VIDEO component videoVideo cable audio in1 Y Audio out S-Video out audio out rgb in1 VIDEO usb control S-Video cable Stereo mini audio cable Stereo mini audio cable rgb in2 rgb out CB/PB audio in2 CR/PR S-VIDEO component videoComponent video out Y CB/PB CR/PR Component video cable Y video audio in1 Audio out Y audio out rgb in1 video usb control rgb in2 rgb out CB/PB audio in2 CR/PR S-video component videoComponent video out Y CB/PB CR/PR Component video cable audio in1 Audio out audio out rgb in1 usb control rgb in2 rgb out CB/PB audio in2 CR/PR S-video component videoStereo mini audio cable 13 14Setting up Connecting power supply WARNING ►Please use extra caution when connecting the power cord as incorrect or faulty connections may result in fire and/or electrical shock. • Only use the power cord that came with the projector. If it is damaged, contact your dealer to newly get correct one. • Only plug the power cord into an outlet rated for use with the power cord's specified voltage range. • Never modify the power cord. Never attempt to defeat the ground connection of the three-pronged plug. 1. Connect the connector of the power cord to the AC inlet of the projector. 2. Firmly plug the power cord's plug into the outlet. AC inlet Connector of the power cord Remote control Remote control Putting batteries WARNING ►Always handle the batteries with care and use them only as directed. Improper use may result in battery explosion, cracking or leakage, which could result in fire, injury and/or pollution of the surrounding environment. • Be sure to use only the batteries specified. Do not use batteries of different types at the same time. Do not mix a new battery with used one. • Make sure the plus and minus terminals are correctly aligned when loading a battery. • Keep a battery away from children and pets. • Do not recharge, short circuit, solder or disassemble a battery. • Do not allow a battery in a fire or water. Keep batteries in a dark, cool and dry place. • If you observe a leakage of a battery, wipe out the flower and then replace a battery. If the flower adheres your body or clothes, rinse well with water immediately. 1. Remove the battery cover. Slide back and remove the battery cover in the direction of the arrow. 2. Insert the batteries. Align and insert the two AA batteries according to their plus and minus terminals as indicated in the remote control. 3. Close the battery cover. Replace the battery cover in the direction of the arrow and snap it back into place. 15 16Remote control Using the remote control CAUTION ►Be careful in handling the remote control. • Do not drop or otherwise expose the remote control to physical impact. • Do not get the remote control wet or place it on wet objects. Doing so may result in malfunction. • Remove the batteries from the remote control and store them in a safe place if you won’t be using the remote control for an extended period. • Replace the batteries whenever the remote control starts to malfunction. • When strong lights, such as direct sunlight or light from an extremely close range (such as from an inverter fluorescent lamp), hit the projector’s remote sensor, the remote control may cause to function. Adjust the direction of the projector to keep light from directly hitting the projector’s remote sensor. The remote control works with the projector’s remote sensor. • The range of the remote sensor is 3 meters with a 60- degree range (30 degrees to the left and right of the remote sensor). • Also a remote signal reflected in the screen etc. may be available. If it is difficult to send a remote signal to the sensor directly, please try. • Since the remote control uses infrared light to send signals to the projector (Class1 LED), be sure to use the remote control in an area free from obstacles that could block the remote control’s output signal to the projector. approx. 3 meters 30o 30o lamp VIDEO RGB SEARCH STANDBY/ON POWER indicator menu FREEZE Turning on the power 1. Make connected sure to that the the projector power cord and is firmly and correctly outlet. 2. Set The the power switch to the ON position. power indicator will light to solid orange. Then wait several seconds because buttons may not function for these several seconds. 3. Press remote the control. STANDBY/ON button on the projector or The projector lamp will light up and the POWER indicator will begin blinking green. When the power is completely on, the indicator will stop blinking light green. To display the picture, select an input signal according to the section "Selecting an input signal" (ffl18). Turning off the power 1. Press remote the control. STANDBY/ON button on the projector or The message "Power off?" will appear on the screen for approximately 5 seconds. 2. Press remote the control STANDBY/ON again while button the message on the projector is visible. or The projector lamp will go off, and the POWER indicator will begin blinking orange. Then the POWER indicator will stop blinking and light to solid orange when the lamp cooling is complete. 3. Make to the sure OFF temp ASPECT AUTO BLANK power MAGNIFY HOME PAGE UP VOLUME ON END PAGE DOWN MUTE OFF KEYSTONE POSITION MENU ENTER ESC RESET POWER (Solid orange) POWER (Blinking green) POWER (Solid green) Power off? POWER (Blinking orange) POWER (Solid orange) that the power indicator lights to solid orange, set the power switch position. The POWER indicator will go off. Power on/off Power on/off WARNING ►When the power is on, a strong light is emitted. Do not look into the lens or vents of the projector. NOTE • Turn the power on/off in right order. Please power on the projector before the connected devices. Power off the projector after the connected devices. STANDBY/ON button Power switch 17 18Operating Operating Adjusting the volume 1. Press A dialog the will VOLUME appear on button the screen on the remote to aid you control. in adjusting the volume. 2. Use To close the cursor the dialog buttons and ▲/▼ to adjust the volume. complete the operation, press the VOLUME button again. Even if you don’t do anything, the dialog will automatically disappear after a few seconds. STANDBY/ON VIDEO RGB SEARCH FREEZE STANDBY/ON ASPECT AUTO BLANK VIDEO RGB SEARCH MAGNIFY HOME PAGE UP VOLUME ON END PAGE DOWN MUTE ASPECT AUTO BLANK OFF KEYSTONE MAGNIFY HOME PAGE UP VOLUME POSITION ESC END PAGE DOWN MUTE OFF Temporarily muting the sound 1. Press A dialog the will MUTE appear button on the on screen the remote indicating control. that you have muted the sound. To restore the sound, press the MUTE or VOLUME button. Even if you don’t do anything, the dialog will automatically disappear after a few seconds. MENU RESET ON ENTER STANDBY/ON VIDEO RGB SEARCH STANDBY/ON VIDEO RGB SEARCH ASPECT AUTO BLANK ASPECT AUTO BLANK MAGNIFY HOME PAGE UP VOLUME ON END PAGE DOWN MUTE HOME PAGE UP FREEZE KEYSTONE POSITION END PAGE DOWN MUTE ESC FREEZE VOLUME KEYSTONE 1. Press input port the for RGB RGB button signal. on the remote control to select an Each time you press the button, the projector switches its RGB input port as below. RGB IN1 ←→ RGB IN2 ● When the TURN ON is selected to the item SEARCH of OPTION menu (ffl37), the projector selects the RGB IN1 port at first. If no input is detected at the RGB IN1 port, projector will check the RGB IN2 port. OFF MAGNIFY ON MENU RESET OFF ENTER Selecting an input signal 1. Press Each time the INPUT you press button the on the projector. button, the projector switches its input port as below. RGB IN1 → RGB IN2 → COMPONENT VIDEO → S-VIDEO → VIDEO STANDBY/ON VIDEO RGB SEARCH ASPECT AUTO BLANK MAGNIFY HOME PAGE UP VOLUME ON END PAGE DOWN MUTE FREEZE KEYSTONE POSITION ESC STANDBY/ON OFF VIDEO RGB SEARCH MENU ASPECT AUTO BLANK ENTER RESET 1. Press an input the port VIDEO for video button signal. on the remote control to select STANDBY/ON VIDEO RGB SEARCH ASPECT AUTO BLANK MAGNIFY HOME PAGE UP VOLUME ON END PAGE DOWN MUTE Each time you press the button, the projector switches its FREEZE KEYSTONE video input port as below. POSITION ESC COMPONENT VIDEO → S-VIDEO → VIDEO ● When the TURN ON is selected to the item SEARCH of OPTION menu (ffl37), the projector selects the COMPONENT VIDEO port at first. If no input is detected at the COMPONENT VIDEO port, projector will begin to check other ports. STANDBY/ON OFF VIDEO RGB SEARCH MENU ASPECT AUTO BLANK ENTER RESET temp power menu Operating Searching an input signal VIDEO RGB SEARCH STANDBY/ON 1. Press The projector the SEARCH will begin button to check on the its remote input ports control. in order to FREEZE find any input signals. Then when an input is found, the projector will stop searching and display the image. If no signal is found, the projector will return to the state selected before the operation. RGB IN1 → RGB IN2 → COMPONENT VIDEO → S-VIDEO → VIDEO Adjusting the zoom and focus 1. Use the zoom knob to adjust the screen size. 2. Use the focus ring to focus the picture. ASPECT AUTO BLANK MAGNIFY HOME PAGE UP VOLUME ON STANDBY/ON OFF END PAGE DOWN MUTE VIDEO RGB SEARCH KEYSTONE ASPECT AUTO BLANK POSITION MENU ENTER ESC RESET Selecting an aspect ratio 1. Press Each time the ASPECT you press button the button, on the the remote projector control. switches the mode for aspect ratio in turn. ❍ At a RGB signal VIDEO RGB SEARCH STANDBY/ON NORMAL → 4:3 → 16:9 FREEZE ❍ At a video signal /no signal 4:3 → 16:9 → SMALL ● The NORMAL mode keeps the original aspect ratio of the signal. ● At a HDTV signal of 1125i (1080i) or 750p (720p) of COMPONENT VIDEO input, only 16:9 mode can be selected. ● Performing the automatic adjustment initializes the aspect ratio setting. STANDBY/ON ASPECT AUTO BLANK VIDEO RGB SEARCH MAGNIFY HOME PAGE UP VOLUME ON END PAGE DOWN MUTE KEYSTONE POSITION ON ESC ASPECT AUTO BLANK OFF MENU MAGNIFY HOME PAGE UP VOLUME ENTER RESET Zoom knob Focus ring 19 20Operating Using the automatic adjustment feature 1. Press the AUTO button on the remote control. ❍ At a RGB signal The vertical position, the horizontal position, the clock phase and horizontal size will be automatically adjusted. Make sure that the application window is set to its maximum size prior to attempting to use this feature. A dark picture may still be incorrectly adjusted. Use a bright picture when adjusting. ❍ At a video signal The video format best suited for the respective input signal will be selected automatically. This function is available only when the AUTO mode is selected to the item VIDEO FORMAT of the INPUT menu (ffl31). For a component video signal, the signal type is identified automatically independently of this function. ● The automatic adjustment operation requires approximately 10 seconds. Also please note that it may not function correctly with some input. Correcting the keystone distortions 1. Press A dialog the will KEYSTONE appear on button on the the screen to remote aid you control. in correcting the distortion. 2. Use To close the cursor the dialog buttons and ▲/▼ to correct the distortion. complete this operation, press the KEYSTONE button again. Even if you don’t do anything, the dialog will automatically disappear after a few seconds. ● This function may not be work well with some input. ● The adjustable range for correcting will vary among inputs. STANDBY/ON VIDEO RGB SEARCH ASPECT AUTO BLANK STANDBY/ON VIDEO RGB SEARCH MAGNIFY HOME PAGE UP VOLUME ON END PAGE DOWN MUTE FREEZE KEYSTONE POSITION ON ESC ASPECT AUTO BLANK HOME PAGE UP VOLUME Adjusting the position 1. Press The “POSITION” the POSITION indication button will on appear the remote on the control. screen. 2. Use position. the cursor buttons ▲/▼/◄/► to adjust the picture When you want to reset the operation, press the RESET button on the remote control during the operation. To complete this operation, press the POSITION button again. Even if you don’t do anything, the dialog will automatically disappear after a few seconds. ● When this function is performed at a video signal, a certain extra such as a line may appear outside a picture. OFF MENU MAGNIFY ENTER RESET FREEZE KEYSTONE STANDBY/ON VIDEO RGB SEARCH ASPECT AUTO BLANK MAGNIFY HOME PAGE UP VOLUME ON END PAGE DOWN MUTE POSITION FREEZE KEYSTONE ENTER POSITION ESC MENU OFF MENU ENTER RESET MAGNIFY HOME PAGE UP VOLUME STANDBY/ON ON VIDEO RGB SEARCH ASPECT AUTO BLANK END PAGE DOWN MUTE MAGNIFY HOME PAGE UP VOLUME OFF ON END PAGE DOWN MUTE OFF FREEZE KEYSTONE FREEZE KEYSTONE POSITION MENU ENTER ESC RESET Operating Using the magnify feature VIDEO RGB SEARCH 1. Press The “MAGNIFY” the ON button indication of MAGNIFY will appear on the on Freezing the screen 1. Press The “FREEZE” the FREEZE indication button will on appear the remote on the control. screen, and the projector will enter the FREEZE mode. To exit the FREEZE mode and restore the screen to normal, press the FREEZE button again. ● The projector automatically exits the FREEZE mode when the input signal changes, or when one of the projector’s buttons or the remote control buttons of STANDBY/ON, SEARCH, RGB, VIDEO, BLANK, AUTO, ASPECT, VOLUME, MUTE, KEYSTONE, POSITION and MENU is pressed. ● If the projector continues projecting a still image for long time, the LCD panel might possibly be printed. Do not leave the projector in FREEZE mode for too long. remote control. the screen (although the indication will disappear after several FREEZE seconds with no operation.), and the projector will enter the MAGNIFY mode. 2. Use To move the cursor the zoom buttons area, ▲/▼ press to the adjust POSITION the zoom button level. in the MAGNIFY mode, then use the cursor buttons ▲/▼/◄/► to move the area. And to finalize the zoom area, press the POSITION button again. To exit the MAGNIFY mode and restore the screen to normal, press the OFF button of MAGNIFY on the remote control. ● The projector automatically exits the MAGNIFY mode when the input signal changes, or when an operation of changing the display condition (automatic adjustment, etc.) is executed. ● Although in the MAGNIFY mode, the keystone distortion condition may vary, it will be restored when the projector exit the MAGNIFY mode. STANDBY/ON VIDEO RGB SEARCH ASPECT AUTO BLANK ASPECT AUTO BLANK MAGNIFY HOME PAGE UP VOLUME ON MAGNIFY HOME PAGE UP VOLUME END PAGE DOWN MUTE FREEZE KEYSTONE END PAGE DOWN MUTE POSITION KEYSTONE ESC Temporarily blanking the screen 1. Press The blank the BLANK screen will button be displayed on the remote instead control. of the screen of input signal. Please refer to the item BLANK of section SCREEN menu (ffl34). To remove the blank screen and return to the input signal screen, press the BLANK button again. ● The projector automatically returns to the input signal screen when the input signal changes, or when one of the projector’s buttons or the remote control buttons are pressed. OFF ON MENU OFF ENTER RESET MAGNIFY HOME PAGE UP VOLUME VIDEO RGB SEARCH STANDBY/ON ON ASPECT AUTO BLANK END PAGE DOWN MUTE MAGNIFY HOME PAGE UP VOLUME ON OFF END PAGE DOWN MUTE OFF FREEZE KEYSTONE FREEZE KEYSTONE POSITION ESC MENU ENTER RESET STANDBY/ON VIDEO RGB SEARCH ASPECT AUTO BLANK HOME PAGE UP END PAGE DOWN MUTE FREEZE STANDBY/ON MAGNIFY VOLUME VIDEO RGB SEARCH ON OFF KEYSTONE POSITION ON ESC ASPECT AUTO BLANK MENU HOME PAGE UP VOLUME RESET MAGNIFY ENTER 21 22Operating Operating the computer screen CAUTION ►Mistaken use of the mouse/keyboard control could damage your equipment. • While using this function, please connect only with a computer. • Before connecting, read the manuals of the computer you will connect. NOTE • It may not be possible to control notebook PC, and other computers with built-in pointing device (e.g. track ball), using this remote control. In this case, before connecting go into BIOS (system setup) and select external mouse, and disable the pointing device. In addition, the mouse may not function if the computer does not have the needed utility program. See your computer’s hardware manual for details. • The USB control can be used with Windows 95 OSR 2.1 or higher. It may not be possible to use the remote control, depending on the computer’s configurations and mouse drivers. • The USB control can be used only for the functions listed below. You cannot do things like press two buttons at once (for instance, pressing two buttons at the same time to move the mouse pointer diagonally). • This function is not available while the lamp is warming up (the POWER indicator flashes green), and while adjusting the volume and display, correcting for trapezoidal distortion, zooming in on the screen, using the BLANK function, or displaying the menu screen. USB mouse and keyboard control 1. Connect the projector’s USB port to the computer via the mouse cable. Available function Remote control operation Move pointer Use ▲, ▼, ◄, ► buttons Left click with mouse Press ENTER button Right click with mouse Press RESET button Press keyboard’s HOME key Press HOME button Press keyboard’s END key Press END button Press keyboard’s PAGE UP key Press PAGE UP button Press keyboard’s PAGE DOWN key Press PAGE DOWN button Press keyboard’s ESC key Press ESC button Multifunctional settings Multifunctional settings Using the menu function This projector has the following menus: PICTURE, IMAGE, INPUT, SETUP, SCREEN, OPTION and EASY MENU. Each of these menus is operated using the same methods. The basic operations of these menus are as follows. 1. Press cursor the buttons MENU on button the projector. on the remote control or one of the The advanced MENU or EASY MENU will appear. 2. Use the cursor buttons ▲/▼ to select a menu. ❍ At the EASY MENU If you want to change it to the advanced MENU, select the "Go to Advanced Menu". ❍ At the advanced MENU Select a menu of PICTURE, IMAGE, INPUT, SETUP, SCREEN or OPTION. If you want to change it to the EASY MENU, select the EASY MENU. 3. Then control, press or the the ENTER cursor button button ► on on the the remote projector control or remote to progress. The display of the selected menu will be active. 4. Use Then the press cursor the buttons cursor button ▲/▼ to ► select on the an projector item to operate. or remote control, or the ENTER button on the remote control to progress. The operation menu of the selected item will appear. 5. Use When the you cursor want buttons▲/▼ to reset the operation, to operate press the item. the RESET button on the remote control during the operation. Note that items whose functions are performed simultaneously with operation (ex. LANGUAGE, H PHASE etc.) aren't reset. When you want to return to the previous display, press the cursor button ◄ on the projector or remote control, or the ESC button on the remote control. 6. Press complete the this MENU operation. button on the remote control again to close the menu and Even if you don't do anything, the dialog will automatically disappear after about 10 seconds. MENU [RGB] :SELECT PICTURE IMAGE INPUT SETUP SCREEN OPTION EASY MENU BRIGHT CONTRAST GAMMA COLOR TEMP COLOR TINT SHARPNESS PROGRESSIVE MY MEMORY +0+0 #1 DEFAULT LOW+0+0+0 TURN OFF SAVE 1 Advanced MENU EASY MENU ASPECT KEYSTONE MODE BRIGHT CONTRAST COLOR TINT SHRPNESS WHISPER MIRROR RESET FILTER TIME LANGUAGE 4:3 +0 NORMAL +0 +0 +0 +0 +3 NORMAL NORMAL 0 ENGLISH Go To Advance Menu... EASY MENU temp power menu MENU button Cursor buttons STANDBY/ON VIDEO RGB SEARCH ASPECT AUTO BLANK HOME PAGE UP END PAGE DOWN MUTE FREEZE POSITION ESC MENU RESET MAGNIFY VOLUME ON OFF KEYSTONE POSITION ESC ENTER ENTER button MENU ENTER RESET button RESET 23 24Multifunctional settings EASY Menu Item Description ASPECT Using the buttons ◄/► switches the mode for aspect ratio. See the item ASPECT of section IMAGE menu (ffl29). KEYSTONE Using the buttons ◄/► corrects the keystone distortion. See the item KEYSTONE of section SETUP menu (ffl33). MODE EASY MENU ASPECT KEYSTONE MODE BRIGHT CONTRAST COLOR TINT SHRPNESS WHISPER MIRROR RESET FILTER TIME LANGUAGE 4:3 With the EASY MENU, items shown in the table below can be performed. +0 NORMAL +0 Select an item using the cursor buttons ▲/▼ on the projector or remote control. Then perform it referring to the following table. +0 +0 +0 +3 NORMAL NORMAL 0 ENGLISH Go To Advance Menu... Using the buttons ◄/► switches the mode of picture type.The modes of picture type are combinations of a mode of GAMMA and a mode of COLOR TEMP. Choose a suitable mode according to the projected source. NORMAL ⬄ CINEMA ⬄ DYNAMIC NORMAL: (COLOR TEMP = MIDDLE) + (GAMMA = #1 DEFAULT) CINEMA: (COLOR TEMP = LOW) + (GAMMA = #2 DEFAULT) DYNAMIC: (COLOR TEMP = HIGH) + (GAMMA = #3 DEFAULT) • When the combination of GAMMA and COLOR TEMP differs from pre-assigned modes above, the display on the menu for the MODE is “CUSTOM”. Please refer to the items GAMMA (ffl26) and COLOR TEMP (ffl27) of PICTURE menu. BRIGHT Using the buttons ◄/► adjusts the brightness. See the item BRIGHT of section PICTURE menu (ffl26). CONTRAST Using the buttons ◄/► adjusts the contrast. See the item CONTRAST of section PICTURE menu (ffl26). COLOR Using the buttons ◄/► adjusts the strength of whole color. See the item COLOR of section PICTURE menu (ffl27). TINT Using the buttons ◄/► adjusts the tint. See the item TINT of section PICTURE menu (ffl27). Multifunctional settings EASY Menu (continued) Item Description SHARPNESS Using the buttons ◄/► adjusts the sharpness. See the item SHARPNESS of section PICTURE menu (ffl27). WHISPER Using the buttons ◄/► turns off/on the whisper mode. See the item WHISPER of section SETUP menu (ffl33). MIRROR Using the buttons ◄/► switches the mode for mirror status. See the item MIRROR of section SETUP menu (ffl33). RESET Performing this item resets all of the items of EASY MENU except FILTER TIME and LANGUAGE. A dialog is displayed to make sure. Selecting RESET using the button ▲ performs reset. FILTER TIME Performing this item resets the filter timer which counts use time of air filter. A dialog is displayed to make sure. Selecting RESET using the button ▲ performs reset. See the item FILTER TIME of section OPTION menu (ffl38). LANGUAGE Select the LANGUAGE to toggle the menu language. Refer to description of LANGUAGE in the SCREEN menu (ffl34). Go To Advanced Menu Select the “Go To Advanced Menu” to use the menu of PICTURE, IMAGE, INPUT, SETUP, SCREEN or OPTION. 25 26Multifunctional settings PICTURE Menu With the PICTURE menu, items shown in the table below can be performed. Select an item using the cursor buttons ▲/▼ on the projector or remote control, and press the cursor button ► on the projector or remote control, or the ENTER button on the remote control to progress. Then perform it referring to the following table. Item Description BRIGHT Using the buttons ▲/▼ adjusts the brightness. : Light ⬄ Dark CONTRAST Using the buttons ▲/▼ adjusts the contrast. : Strong ⬄ Weak GAMMA MENU [RGB] :SELECT PICTURE IMAGE INPUT SETUP SCREEN OPTION EASY MENU BRIGHT CONTRAST GAMMA COLOR TEMP COLOR TINT SHARPNESS PROGRESSIVE MY MEMORY +0+0 #1 DEFAULT LOW +0+0+0 TURN OFF SAVE 1 Using the buttons ▲/▼ switches the GAMMA mode. : #1 DEFAULT ⬄ #1 CUSTOM ⬄ #2 DEFAULT #3 CUSTOM ⬄ #3 DEFAULT ⬄ #2 CUSTOM To adjust #1 CUSTOM, #2 CUSTOM or #3 CUSTOM Selecting a mode of CUSTOM and then pressing the button ► or the ENTER button 1ENTER : 2displays a dialog to aid you in adjusting the mode. This function is useful when you want to change the brightness of particular tones. +0 +0 Choose an item using the buttons ◄/►, and adjust the level using the buttons ▲/▼. You can display a test pattern for checking the effect of your adjustment by pressing the ENTER button. Each time you press the ENTER button, the pattern changes as below. No pattern ⇨ Gray scale of 9 steps Ramp ⇦ Gray scale of 15 steps Eight of equalizing bars corresponds to eight of tone level of test pattern except the darkest in the left end. If you want to adjust the 2nd tone from left end on the test pattern, use the equalizing adjustment bar “1”. The darkest tone at the left end of the test pattern cannot be controlled with any of equalizing adjustment bar. 3+0 4+0 5+0 6+0 7+0 8+0 GAMMA [CUSTOM 1] Multifunctional settings PICTURE Menu (continued) Item Description Using the buttons ▲/▼ switches the mode of color temperature. HIGH ⬄ MIDDLE ⬄ LOW ⬄ CUSTOM To adjust CUSTOM Selecting the CUSTOM and then pressing the button ► or the ENTER button displays a dialog to aid you in adjusting the OFFSET and/or GAIN Rof CUSTOM mode. OFFSET adjustments change the color intensity COLOR TEMP on the whole tones of the test pattern. GAIN adjustments mainly affect color intensity +0 on the brighter tones of the test pattern. Choose an item using the buttons ◄/►, and adjust the level using the buttons ▲/▼. You can display a test pattern for checking the effect of your adjustment by pressing the ENTER button. Each time you press the ENTER button, the pattern changes as below. No pattern ⇨ Gray scale of 9 steps Ramp ⇦ Gray scale of 15 steps COLOR ENTER : OFFSET GBRGAIN GB+0 +0+0 +0 +0 COLOR TEMP Using the buttons ▲/▼ adjusts the strength of whole color. Strong ⬄ Weak • This item can be selected only at a video signal. TINT Using the buttons ▲/▼ adjusts the tint. Green ⬄ Red • This item can be selected only at a video signal except for SECAM. SHARPNESS Using the buttons ▲/▼ adjusts the sharpness. Strong ⬄ Weak 27 28Multifunctional settings PICTURE Menu (continued) Item Description PROGRESSIVE Using the buttons ▲/▼ switches the progressive mode. TV ⬄ FILM ⬄ TURN OFF • This function performs only at an interlaced signal of a VIDEO input, a S-VIDEO input or a COMPONENT VIDEO input of 525i (480i) or 625i (576i) signal. • When the TV or FILM is selected, the screen image will be crisper. The FILM mode is adaptable to the 2-3 Pull-Down system to the conversion. But these may cause a certain defect (for example, jagged line) of the picture at a quick moving object. In such a case, please select the TURN OFF, even though the screen image may lose the crisp. MY MEMORY Selecting a mode of MY MEMORY using the buttons ▲/▼ and then pressing the button ► or the ENTER button performs each function. LOAD1 ⬄ LOAD2 ⬄ LOAD3 ⬄ LOAD4 SAVE4 ⬄SAVE3 ⬄ SAVE2 ⬄ SAVE1 This projector has 4 numbered memories for adjustment data. Performing the LOAD1, LOAD2, LOAD3 or LOAD4 loads the data on the memory whose number corresponds with the command’ s number, and adjusts the picture automatically depending on the data. Performing the SAVE1, SAVE2, SAVE3 or SAVE4 puts the current adjustment data on the memory whose number corresponds with the command’s number. Multifunctional settings IMAGE Menu With the IMAGE menu, items shown in the table below can be performed. Select an item using the cursor buttons ▲/▼ on the projector or remote control, and press the cursor button ► on the projector or remote control, or the ENTER button on the remote control to progress. Then perform it referring to the following table. Item Description ASPECT MENU [RGB] :SELECT PICTURE IMAGE INPUT SETUP SCREEN OPTION EASY MENU ASPECT 4:3 OVER SCAN 95V POSITION 25H POSITION 142 H PHASE 16H SIZE 1344 AUTO ADJUST Using the buttons ▲/▼ switches the mode for aspect ratio. At a RGB signal 4:3 ⬄ 16:9 ⬄ NORMAL At a video signal / no signal 4:3 ⬄ 16:9 ⬄ SMALL • The NORMAL mode keeps the original aspect ratio of the signal. • At a HDTV signal of 1125i (1080i) or 750p (720p) of COMPONENT VIDEO input, this item can't be selected. • Performing the automatic adjustment initializes the aspect ratio setting. OVER SCAN Using the buttons ▲/▼ adjusts the over-scan ratio. Large (It reduces picture) ⬄ Small (It magnifies picture) • This item can be selected only at a video signal. • When this adjustment is too large, certain degradation may appear at the frame area of the picture. In such a case, please adjust small. V POSITION Using the buttons ▲/▼ adjusts the vertical position. Up ⬄ Down H POSITION Using the buttons ▲/▼ adjusts the horizontal position. Left ⬄ Right H PHASE Using the buttons ▲/▼ adjusts the horizontal phase to eliminate flicker. Right ⬄ Left • This item can be selected only at a RGB signal or a component video signal. 29 30Multifunctional settings IMAGE Menu (continued) Item Description H SIZE Using the buttons ▲/▼ adjusts the horizontal size. Large ⬄ Small • This item can be selected only at a RGB signal. • When this adjustment is excessive, the picture may not be displayed correctly. In such a case, please reset the adjustment pressing the RESET button on the remote control during this operation. AUTO ADJUST Selecting this item performs the automatic adjustment feature. At a RGB signal The vertical position, the horizontal position, the clock phase and horizontal size will be automatically adjusted. Make sure that the application window is set to its maximum size prior to attempting to use this feature. A dark picture may still be incorrectly adjusted. Use a bright picture when adjusting. At a video signal The video format best suited for the respective input signal will be selected automatically. This function is available only when the AUTO mode is selected to the item VIDEO FORMAT of INPUT menu. For a component video signal, the signal type is identified automatically independently of this function. • The automatic adjustment operation requires approximately 10 seconds. Also please note that it may not function correctly with some input. Multifunctional settings INPUT Menu With the INPUT menu, items shown in the table below can be performed. Select an item using the cursor buttons ▲/▼ on the projector or remote control, and press the cursor button ► on the projector or remote control, or the ENTER button on the remote control to progress. Then perform it referring to the following table. Item Description MENU [RGB] :SELECT PICTURE IMAGE INPUT SETUP SCREEN OPTION EASY MENU COLOR SPACE COMPONENT VIDEO FORMAT FRAME LOCK INFORMATION COLOR SPACE COMPONENT VIDEO FORMAT FRAME LOCK INFORMATION AUTO COMPONENT AUTO TURN ON AUTO COMPONENT AUTO TURN ON AUTO COMPONENT AUTO TURN ON COLOR SPACE Using the buttons ▲/▼ switches the mode for color space. AUTO ⬄ RGB ⬄ SMPTE240 ⬄ REC709 ⬄ REC601 • This item can be selected only at a RGB signal or a component video signal. • The AUTO mode automatically selects the optimum mode. • The AUTO operation may not work well at some signals. In such a case, it might be good to select the SMPTE240 or the REC709. COMPONENT COMPONENT ⬄ SCART RGB When the SCART RGB is selected, the COMPONENT VIDEO port function as a port for a SCART RGB signal input. A SCART adapter and SCART cable realize a SCART RGB input to the projector. For details, ask your dealer. Using the buttons ▲/▼ switches the function of COMPONENT VIDEO port. VIDEO FORMAT • This item performs only at a video signal from the VIDEO port or the S-VIDEO port. For a component video signal, the signal type is identified automatically independently of this function. Using the buttons ▲/▼ switches the mode for video format. AUTO ⬄ NTSC ⬄ PAL ⬄ SECAM N-PAL ⬄ M-PAL ⬄ NTSC4.43 • The AUTO mode automatically selects the optimum mode. • The AUTO operation may not work well at some signals. If the picture becomes unstable (ex. an irregular picture, a color lack), please select the mode depending on the input signal. FRAME LOCK • This item performs only at a RGB signal with vertical frequency of 50 to 60 Hz for the models X45 and X55, or 50 to 72Hz for the model S55. Using the buttons ▲/▼ turns the frame lock function on/off. TURN ON ⬄ TURN OFF • When the TURN ON is selected, a moving picture is displayed more smoothly. • This function may cause a certain degradation of the picture. In such a case, please select the TURN OFF. 31 32Multifunctional settings INPUT Menu (continued) Item Description INFORMATION Selecting this item displays a dialog titled “INPUT INFORMATION”. It shows the information about the current input. INPUT-INFORMATION RGB 1024x768 @60.0 FRAME LOCK INPUT-INFORMATION S-VIDEO SECAM AUTO INPUT-INFORMATION COMPONENT 576i @50 SCART RGB • The “FRAME LOCK” message on the dialog means the frame lock function is working (ffl31). • The “SCART RGB” message means the COMPONENT VIDEO port is working as a SCART RGB input port. Please refer to the item COMPONENT in this section. (ffl31) • This item is can't be selected at no signal. Multifunctional settings SETUP Menu With the SETUP menu, items shown in the table below can be performed. Select an item using the cursor buttons ▲/▼ on the projector or remote control, and press the cursor button ► on the projector or remote control, or the ENTER button on the remote control to progress. Then perform it referring to the following table. Item Description KEYSTONE MENU [RGB] :SELECT PICTURE IMAGE INPUT SETUP SCREEN OPTION EASY MENU KEYSTONE +0WHISPER NORMAL MIRROR NORMAL VOLUME 16 Using the buttons ▲/▼ corrects the keystone distortion. Upper in the data ⬄ Lower in the data • The adjustable range of this function will vary with the type of input signal. At some signals, this function may not work well. • When the V:INVERT or the H&V:INVERT is selected under the item MIRROR, if the projector screen is inclined or if the projector is angled downward, this function may not work correctly. • When the zoom adjustment is set to the TELE side, this correction may be excessive. This function should be used with zoom set to WIDE whenever possible. WHISPER Using the buttons ▲/▼ turns off/on the whisper mode. NORMAL ⬄ WHISPER • When the WHISPER is selected, acoustic noise and screen brightness are reduced. MIRROR Using the buttons ▲/▼ switches the mode for mirror status. NORMAL ⬄ H:INVERT ⬄ V:INVERT ⬄ H&V:INVERT VOLUME Using the buttons ▲/▼ adjusts the volume. High ⬄ Low 33 34Multifunctional settings SCREEN Menu With the SCREEN menu, items shown in the table below can be performed. Select an item using the cursor buttons ▲/▼ on the projector or remote control, and press the cursor button ► on the projector or remote control, or the ENTER button on the remote control to progress. Then perform it referring to the following table. Item Description LANGUAGE MENU [RGB] :SELECT PICTURE IMAGE INPUT SETUP SCREEN OPTION EASY MENU LANGUAGE MENU POSITION OSD BRIGHT BLANK START UP MyScreen MyScreen Lock MESSAGE ENGLISH 5BLACK ORIGINAL TURN OFF TURN ON Using the buttons ▲/▼ switches the OSD (On Screen Display) language. ENGLISH ⬄ FRANÇAIS ⬄ DEUTSCH ⬄ ESPAÑOL ⬄ ITALIANO NORSK ⬄ NEDERLANDS ⬄ PORTUGUÊS ⬄ ⬄ ⬄ SVENSKA ⬄ ⬄ SUOMI ⬄ POLSKI MENU POSITION Using the buttons ◄/►/▲/▼ adjusts the menu position. To quit the operation, press the MENU button on the remote control or keep no operation for 10 seconds. OSD BRIGHT Using the buttons ▲/▼ switches the brightness level of the OSD (On Screen Display). Bright ⬄ Dark BLANK Using the buttons ▲/▼ switches the mode for the blank screen. The blank screen is the screen for the temporarily blanking feature (ffl21). It is displayed by pressing the BLANK button on the remote control. MyScreen ⬄ ORIGINAL ⬄ BLUE ⬄ WHITE ⬄ BLACK MyScreen is the screen you can register a desired screen. ORIGINAL screen is the existing standard screen. BLUE, WHITE and BLACK are non-patterned (plain) screens in each color. • To avoid remaining as an afterimage, the MyScreen and the ORIGINAL screens will change to the BLACK screen after several minutes. • For the MyScreen, please refer to the item MyScreen (ffl35). Multifunctional settings SCREEN Menu (continued) Item Description START UP Using the buttons ▲/▼ switches the mode for the start up screen. The start up screen is the screen displayed when no signal or an unsuitable signal is detected. MyScreen is the screen you can register a desired screen. ORIGINAL screen is the existing standard screen. When the TURN OFF is selected, the BLUE screen is used. MyScreen ⬄ ORIGINAL ⬄ TURN OFF • To avoid remaining as an afterimage, the MyScreen and the ORIGINAL screens will change to the BLANK screen after several minutes. If also the BLANK screen is the MyScreen or ORIGINAL, it will change to the BLACK screen. • For the MyScreen, please refer to the item MyScreen below. About the BLUE, BLACK and BLANK screens, please refer to the item BLANK (ffl34). My Screen This item functions for capturing the MyScreen of the blank screen and the start up screen. Please execute displaying the input including the picture you want to capture. 1. Selecting this item displays a dialog titled “MyScreen”. It will ask you if you start capturing the picture from the current screen. Please wait for the target picture to be displayed, and press the ENTER button on the remote control when the picture is display. The picture will freeze and the frame for capturing appears. To stop performing, press the RESET or ESC button on the remote control. 2. Using the buttons ◄/►/▲/▼ adjust the frame position. Please move the frame to the position of the picture which you want to use. To start registration, press the ENTER button on the remote control. To restore the screen and return to the previous dialog, press the RESET or ESC button on the remote control. Registration takes several minutes. When the registration is completed, the registered screen and the message “MyScreen registration is finished.” are displayed for several seconds. If the registration failed, the message “A capturing error has occurred. Please try again.” is displayed. My Screen Lock Using the buttons ▲/▼ turns on/off the MyScreen lock function. TURN ON ⬄ TURN OFF When the TURN ON is selected, the item MyScreen cannot be performed. Use this function for protecting the current MyScreen. 35 36Multifunctional settings SCREEN Menu (continued) Item Description MESSAGE Using the buttons ▲/▼ turns on/off the message function. TURN ON ⬄ TURN OFF When the TURN ON is selected, the following message function works. “AUTO IN PROGRESS” while automatically adjusting ”NO INPUT IS DETECTED” ”SYNC IS OUT OF RANGE” ”Searching ....” while searching for an input signal ”Detecting....” when an input signal is detected The indication of the input signal by changing The indication of the aspect ration by changing . Multifunctional settings OPTION Menu With the OPTION menu, items shown in the table below can be performed. Select an item using the cursor buttons ▲/▼ on the projector or remote control, and press the cursor button ► on the projector or remote control, or the ENTER button on the remote control to progress, except for the items LAMP TIME and FILTER TIME. Then perform it referring to the following table. Item Description SEARCH MENU [RGB] :SELECT PICTURE IMAGE INPUT SETUP SCREEN OPTION EASY MENU SEARCH TURN ON AUTO OFF 0LAMP TIME 0FILTER TIME 0 SERVICE Using the buttons ▲/▼ turns on/off the automatic signal search function. TURN ON ⬄ TURN OFF When the TURN ON is selected, detecting no signal automatically cycles through input ports in order of following. Then when an input is found, the projector will stop searching and display the image. RGB IN1 ⇨ RGB IN2 ⇨ COMPONENT VIDEO ⇨ S-VIDEO ⇨ VIDEO AUTO OFF Using the buttons ▲/▼ adjusts the time to count down to automatically turn the projector off. Long (max. 99 minutes) ⬄ Short (min. 0 minute = DISABLE) AUTO OFF ENABLE 1 AUTO OFF DISABLE 0 When the time is set to 0, the projector is not turned off automatically. When the time is set to 1 to 99, and when the passed time with a no-signal or an unsuitable signal reaches at the set time, the projector lamp will go off and the power indicator begins blinking. Please refer to the section “Turning off the power” (ffl17). LAMP TIME The lamp time is the time counted after the last resetting. It is shown in the OPTION menu as the use time of the lamp. Pressing the RESET button on the remote control for about 3 seconds displays a dialog. To reset the lamp time, select the RESET using the button ▲. RESET ⇦ CANCEL • Please reset the lamp time only when you have replaced the lamp, for correct messages about the lamp. • About the lamp replacement, please see the section "Lamp" (ffl 39, 40). 37 38Multifunctional settings OPTION Menu (continued) Item Description FILTER TIME The filter time is the time counted after the last resetting. It is shown in the OPTION menu as the use time of the air filter. Pressing the RESET button on the remote control for about 3 seconds displays a dialog. To reset the filter time, select the RESET using the button ▲. RESET ⇦ CANCEL • Please reset the filter time only when you have cleaned or replaced the air filter, for correct messages about the air filter. • About the caring the air filter, please see the section "Air filter" (ffl 41). SERVICE Selecting this item displays the SERVICE menu. Select an item using the buttons ▲/▼, and press the button ► or the ENTER button on the remote control to progress. FAN SPEED ⬄ GHOST ⬄ FACTORY RESET FAN SPEED Using the buttons ▲/▼ switches the rotation speed of the cooling fans. The HIGH is the mode for use at highlands etc. Note that the projector is noisier when the HIGH is selected. HIGH ⬄ NORMAL GHOST 1. Select a color element of ghost using the buttons ◄/►. 2. Adjust the selected element using the buttons ▲/▼ to disappear ghost. FACTORY RESET Selecting RESET using the button ▲ performs this function. By this function, all the items in all of menu will collectively return to the initial setting. Note that the items LAMP TIME, FILTER TIME and LANGUAGE are not reset. RESET ⇦ CANCEL Maintenance Maintenance Lamp WARNING HIGH VOLTAGE HIGH TEMPERATURE HIGH PRESSURE ►The projector uses a high-pressure mercury glass lamp. The lamp can break with a loud bang, or burn out, if jolted or scratched, handled while hot, or worn over burn time. out soon Note after that you each start lamp using has them. a different In addition, lifetime, when and the some bulb may bursts, burst it or is possible for shards of glass to fly into the lamp housing, and for gas containing mercury to escape from the projector’s vent holes. ►About disposal of a lamp • This product contains a mercury lamp; do not put in trash. Dispose of in accord with environmental laws. For lamp recycling, go to www.lamprecycle.org. (in the US) For the US) product or www.epsc.ca disposal, contact (in Canada). your local government agency or www.eiae.org (in For more information, call your dealer. • If the lamp should break (it will make a loud bang when it does), unplug replacement the power lamp cord from from your the local outlet, dealer. and Note make that sure shards to request of glass a could damage the projector’s internals, or cause injury during handling, Disconnect so • If please the lamp do not should try to break clean the (it will projector make or a replace loud bang the lamp when yourself. it does), the plug from the power outlet ventilate the room well, and make sure not to breathe the gas that comes • Before out replacing of the projector the lamp, vents, turn or the get projector it in your off eyes and or unplug mouth. the power cord, then wait at least 45 minutes for the lamp to cool sufficiently. Handling lamp. the lamp while hot can cause burns, as well as damaging the • Never unscrew except the appointed (marked by an arrow) screws. • Do not open the lamp door while the projector is suspended from above. shards will This fall is out dangerous, when the since cover if is the opened. lamp’s In bulb addition, has broken, working the in high places is dangerous, so ask your local dealer to have the lamp replaced • Do not even use the if the projector bulb is not with broken. the lamp door removed. At the lamp replacing, make sure that the screws are screwed in firmly. Loose screws could result in damage or injury. • Use only the lamp of the specified type. • If the lamp breaks soon after the first time it is used, it is possible that there are electrical problems elsewhere besides the lamp. If this happens, • Handle with contact care: jolting your or local scratching dealer could or a cause service the lamp representative. bulb to burst during use. • If the indicators or a message prompts you to replace the lamp (see the replace section the "Related lamp as soon Messages" as possible. and "Regarding Using the the lamp indicator for long Lamps"), periods of time, or past the replacement date, could cause it to burst. Do not use old (used) lamps; this is a cause of breakage. 39 Maintenance Lamp (continued) When the indicators or a message prompts you to replace the lamp, replace the lamp as soon as possible. 1. Turn the projector off, and unplug the power cord. Allow the lamp to cool for at least 45 minutes. 2. To prepare a new lamp, contact your dealer and tell the lamp type number = 78-6969-9790-3. If the projector is mounted on the ceiling, or if the lamp has broken, also ask the dealer to replace the lamp. In the case of replacement by yourself, 3. After making sure that the projector has cooled adequately, slowly turn over the projector, so that the bottom is facing up. 4. Unscrew the screw of the lamp door, and remove the lamp door. 5. Loosen the 2 screws (marked by arrow) of the lamp, and slowly pick up the lamp by the handles. 6. Insert the new lamp, and retighten firmly two screws that are loosened in the previous process to lock it in place. 7. Interlocking the 2 tabs of the lamp door to the projector, position the lamp door on the projector. Then tighten the screw of the lamp door. 8. Slowly turn the projector so that the top is facing up. 9. Turn the projector on, and reset the lamp time using the LAMP TIME function of OPTION menu (ffl37). NOTE • When the lamp has been replaced after the message of "THE POWER WILL TURN OFF AFTER 0hr." is displayed, complete the following operation within 10 minutes of switching power on. • Incorrectly resetting of the lamp timer (resetting without replacement, or neglect of resetting after replacement) will result in incorrect message functions. 40 Lamp door Screw Screws marked by arrow Tabs Screw Maintenance Air filter When the indicators or a message prompts you to clean the air filter, clean the air filter as soon as possible. If the air filter becomes clogged by dust or the like, internal temperatures rise and the power may be automatically turned off for malfunction prevention. 1. Turn Allow the the projector projector off, to cool and unplug for at least the power 45 minutes. cord. And prepare a vacuum cleaner. 2. After slowly making turn the sure projector that the so projector that the lens-side is cool adequately, is facing up. Please be careful for a projector not to fall. While the projector is placed lens-side up, hold the projector. 3. Unhook screwdriver the claw or similar, of the and filter remove cover using the filter a minus cover. 4. Holding the air filter’s knob, pull the air filter off. 5. Apply air filter. a vacuum And then cleaner slowly WARNING ►Before caring, make sure the power switch is off and the power cable is not plugged in, then allow the projector to cool sufficiently. The care in a high temperature state of the projector could cause a burn and/or malfunction to the projector. ►Use only the air filter of the specified type. Do not use the projector with the air filter and filter cover removed. ►Avoid wetting the projector or inserting liquids in the projector. It could result in a fire, an electric shock, and and/or malfunction to the projector. CAUTION ►Please replace the air filter when it is damaged or too soiled, and also when you replace the lamp. to the vent of the projector for the turn the projector bottom up. 6. Apply a vacuum cleaner to the air filter and filter cover. Please replace the air filter when it is damaged or too soiled. To prepare a new air filter, contact your dealer and tell the air filter type number = 78-8118-9376-3. An air filter of specified type will come even with the replacement lamp for this projector. 7. Position of "PUSH" the word cleaned with air claws filter to or fix a the new air air filter. filter into place, and push the points 8. Replace the filter cover and snap it back into place. 9. Slowly turn the projector so that the top is facing up. 10. Turn function the of projector OPTION on, menu and reset (ffl38). the filter time using the FILTER TIME NOTE • Incorrectly resetting of the filter timer (resetting without replacement, or neglect of resetting after replacement) will result in incorrect message functions. Filter cover Filter cover’s claw Air filter Air filter’s knob 41 42Maintenance Other care WARNING ►Before caring, make sure the power switch is off and the power cable is not plugged in, and then allow the projector to cool sufficiently. The care in a high temperature state of the projector could cause a burn and/or malfunction to the projector. ►Never try to care for the inside of the projector personally. Doing is so dangerous. ►Avoid wetting the projector or inserting liquids in the projector. It could result in a fire, an electric shock, and and/or malfunction to the projector. • Don’t put a container containing water, cleaner or chemicals near the projector. • Don’t use aerosols or sprays. CAUTION ►Please take right care of the projector according to the following. Incorrect care could cause not only an injury but adverse influence such as discoloration, peeling paint, etc. • Do not use cleaner or chemicals other than those listed below. • Do not polish or wipe with hard objects. Inside of the projector In order to ensure the safe use of your projector, please have it cleaned and inspected by your dealer about once every 2 years. Caring for the lens If the lens is flawed, soiled or fogged, it could cause deterioration of display quality. Please take care of the lens, being cautious of the handling. 1. Turn sufficiently. the projector off, and unplug the power cord. Allow the projector to cool 2. After with a making commercially sure that available the projector lens-cleaning is cool adequately, wipe. Do not lightly touch wipe the the lens lens directly with your hand. Caring for the cabinet and remote control Incorrect care could have adverse influence such as discoloration, peeling paint, etc.1. Turn sufficiently. the projector off, and unplug the power cord. Allow the projector to cool 2. After or a soft making cloth. sure that the projector is cool adequately, lightly wipe with gauze If soiling is severe, dip soft cloth in water or a neutral cleaner dilute in water, and wipe lightly after wringing well. Then, wipe lightly with a soft, dry cloth. Troubleshooting Troubleshooting Related messages When the unit's power is on, messages such as those shown below may be displayed. When any such message is displayed on the screen, please respond as described below. If the same message is displayed after the treatment, or if a message other than the following appears, please contact your dealer or service company. Although these messages will be automatically disappeared around several minutes, it will be reappeared every time the power is turned on. Message Description CHANGE THE LAMP AFTER REPLACING LAMP, RESET THE LAMP TIMER. The time the lamp timer has counted is approaching 2000 hours. Preparation of a new lamp, and an early lamp change is recommended. After you have change the lamp, please be sure to reset the lamp timer (ffl37). CHANGE THE LAMP AFTER REPLACING LAMP, RESET THE LAMP TIMER. THE POWER WILL TURN OFF AFTER hr. The time the lamp timer has counted is approaching 2000 hours, so a lamp change within hours is recommended. When lamp usage reaches 2000 hours, the power will automatically be turned off. Please change the lamp by referring to the section “Lamp”. After you have changed the lamp, please be sure to reset the lamp timer (ffl37). CHANGE THE LAMP AFTER REPLACING LAMP, RESET THE LAMP TIMER. THE POWER WILL TURN OFF AFTER 0 hr. As the time the lamp timer has counted has reached 2000 hours, the power will soon be automatically turned off. Please immediately turn the power off, and change the lamp by referring to the section “Lamp”. After changing the lamp, please be sure to reset the lamp timer (ffl37). NO INPUT IS DETECTED ON ** There is no input signal. Please confirm the signal input connection, and the status of the signal source. SYNC IS OUT OF RANGE ON fH **kHz fV *Hz The horizontal or vertical wavelength of the inputted signal is outside of the response parameters of this unit. Please confirm the specs for this unit or the signal source specs. CHECK THE AIR FLOW The internal portion temperature is rising. Please turn the power OFF, and allow the unit to cool down at least 20 minutes. After having confirmed the following items, please turn the power ON again. • Is there blockage of the air passage aperture? • Is the air filter dirty? • Does the peripheral temperature exceed 35°C? • If the same indication is displayed after the treatment, please set the HIGH at the FAN SPEED of the item SERVICE of the OPTION menu. 43 44Troubleshooting Related messages (continued) Message Description CLEAN THE AIR FILTER POWER OFF FIRST, THEN CLEAN THE AIR FILTER. AFTER CLEANING THE AIR FILTER, RESET THE FILTER TIMER. A note of precaution when cleaning the air filter. Please immediately turn the power OFF, and clean or change the air filter by referring to the “Air Filter” section of this manual. After you have cleaned or changed the air filter, please be sure to reset the filter timer (ffl38). NOTE • A lamp has a finite product life. Lamps are characterized by the fact that, after long hours of usage, a lamp will no longer light up, or the lamp will break or burst, etc. This projector is equipped with an automatic shut-down function, such that the power will automatically be turned off when lamp usage time has reached 2000 hours. Please be aware, however, that among lamp types, there are major differences in product lifetimes; a lamp may thus fail to light even prior to the functioning of the automatic shut-down function of this projector. Troubleshooting Regarding the indicator lamps Lighting and flashing of the POWER indicator, the LAMP indicator, and the TEMP indicator have the meanings as described in the table below. Please respond in accordance with the instructions within the table. If the same indication is displayed after the treatment, or if an indication other than the following is displayed, please contact your dealer or service company. POWER indicator LAMP indicator TEMP indicator Description Lighting In Orange Turned off The projector is in a standby state. Please refer to the section “Power On/Off”. Blinking In Green Turned off Turned off Turned off The projector is warming up. Please wait. Lighting In Green Turned off Turned off The projector is in an on state. Ordinary operations may be performed. Blinking In Orange Turned off Turned off The projector is cooling down. Please wait. Blinking In Red The projector is cooling down. A certain error has been detected. Please wait until the POWER indicator finishes blink, and then perform the proper response measure using the item descriptions below as reference. Blinking In Red or Lighting In Red (discre- tionary) (discre- tionary) The lamp does not light, and there is a possibility that interior portion has become heated. Please turn the power off, and allow the unit to cool down at least 20 minutes. After the projector has sufficiently cooled down, please make confirmation of the following items, and then turn the power on again. • Is there blockage of the air passage aperture? • Is the air filter dirty? • Does the peripheral temperature exceed 35°C? If the same indication is displayed after the treatment, please change the lamp by referring to the section “Lamp”. Blinking In Red or Lighting In Red Lighting In Red Turned off The lamp door has not been properly fixed (attached). Please turn the power off, and allow the unit to cool Blinking In Red down at least 45 minutes. After the projector has sufficiently cooled down, please make confirmation of the attachment state of the lamp door. After performing any needed maintenance, turn the power on again. If the same indication is displayed after the treatment, please contact your dealer or service company. Turned off 45 46Troubleshooting Regarding the indicator lamps (continued) POWER indicator LAMP indicator TEMP indicator Description Blinking In Red or Lighting In Red The cooling fan is not operating. Please turn the power off, and allow the unit to cool down at least 20 minutes. After the projector has sufficiently cooled down, please make confirmation that no foreign matter has become caught in the fan, etc., and then turn the power on again. If the same indication is displayed after the treatment, please contact your dealer or service company. Blinking In Red or Lighting In Red Turned off Blinking In Red There is a possibility that the interior portion has become heated. Please turn the power off, and allow the unit to cool down at least 20 minutes. After the projector has sufficiently cooled down, please make confirmation of the following items, and then turn the power on again. • Is there blockage of the air passage aperture? • Is the air filter dirty? • Does the peripheral temperature exceed 35°C? If the same indication is displayed after the treatment, please set the HIGH at the FAN SPEED of the item SERVICE of the OPTION menu. Lighting In Green Turned off Lighting In Red There is a possibility that the interior portion has become overcooled. Please use the unit within the usage temperature parameters (5°C to 35°C). After the treatment, resent the power to ON. Lighting In Green Alternative blinking in Red It is time to clean the air filter. Please immediately turn the power OFF, and clean Simultaneous or change the air filter by referring to the section “Air blinking in Red Filter”. After cleaning or changed the air filter, please be sure to reset the filter timer. After the treatment, resent the power to ON. NOTE • When the interior portion has become overheated, for safety purposes, the power source is automatically turned off, and the indicator lamps may also be turned off. In such a case, press the “○” (OFF) side of the power switch, and wait at least 45 minutes. After the projector has sufficiently cooled down, please make confirmation of the attachment state of the lamp and lamp door, and then turn the power on again. Troubleshooting Phenomena that may easily be mistaken for machine defects WARNING ►Never use the projector if abnormal operations such as smoke, strange odor, excessive sound, damaged casing or elements or cables, penetration of liquids or foreign matter, etc. should occur. In such cases, immediately turn off the power switch and then disconnect the power plug from the power outlet After making sure that the smoke or odor has stopped, contact your dealer or service company. 1. Before This operation requesting sometimes repair, please resolves check your in problem. accordance with the following chart. If the situation cannot be corrected, 2. The Restart projector’s switch by microprocessor using a cocktail may stick need or similar to be reset. and the Please projector push will the restart. 3. Some SERVICE setting menu may in be the wrong. OPTION Please menu use (ffl38) the to FACTORY reset all settings RESET function to factory of default. Then, if the problem is not removed after maintenance, please contact your dealer or service company. Phenomenon Cases not involving a machine defect Reference page Power does not come on. The electrical power cord is not plugged in. Correctly connect the power cord. 14 The power switch is not set to the on position. Set the power switch to [ | ] (On). 17 The main power source has been interrupted during operation such as by a power outage (blackout), etc. Please turn the power off, and allow the unit to cool down at least 20 minutes. After the projector has sufficiently cooled down, please turn the power on again. 17 Either there is no lamp and/or lamp door, or either of these has not been properly fixed. Please turn the power off, and allow the unit to cool down at least 45 minutes. After the projector has sufficiently cooled down, please make confirmation of the attachment state of the lamp and lamp door, and then turn the power on again. 39, 40 47 Troubleshooting Phenomena that may easily be mistaken for machine defects (continued) Phenomenon Cases not involving a machine defect Reference page No pictures are displayed. NOTE • Although bright spots or dark spots may appear on the screen, this is a unique characteristic of liquid crystal displays, and such do not constitute or imply a machine defect. The signal cables are not correctly connected. Correctly connect the connection cables. 11 The brightness is adjusted to an extremely low level. Adjust the BRIGHT to a higher level using the menu function or the remote control. 24, 26 The computer cannot detect the projector as a plug and play monitor. Make sure that the computer’s can detect a plug and play monitor using other plug and play monitor. 11 Colors have a faded- out appearance, or Color tone is poor. Color settings are not correctly adjusted. Perform picture adjustments by changing the COLOR TEMP, COLOR, TINT and/or COLOR SPACE settings, using the menu functions. 24, 26, 31 COLOR SPACE setting is not suitable. Change the COLOR SPACE setting to AUTO, RGB, SMPTE240 , REC709 or REC601. 31 Pictures appear dark. The brightness and/or contrast are adjusted to an extremely low level. Adjust the BRIGHT and/or CONTRAST settings to a higher level using the menu function. 25, 26 The WHISPER function is working. Select the NORMAL to the item WHISPER in the SETUP menu. 25, 33 The lamp is approaching the end of its product lifetime. Replace the lamp. 39, 40 Pictures appear blurry. Either the focus and/or horizontal phase settings are not properly. Adjust the focus using the focus ring, and/or H PHASE using the menu function. 19, 29 The lens is dirty or misty. Clean the lens by referring to the section “Caring for the lens”. 42 48 Specifications Specifications NOTE • This specifications are subject to change without notice. Item Specification Product name Liquid crystal projector Liquid Crystal panel Panel size 1.8 cm (0.7 type) Drive system TFT active matrix Pixels S55: 480,000 pixels (800 horizontal x 600 vertical) X45/X55: 786,432 pixels (1024 horizontal x 768 vertical) Lens Zoom lens F=1.7 ~ 1.9 f=21.8 ~ 26.2 mm Lamp 165W UHB Power Supply AC100-120V/2.7A, AC220-240V/1.5A Power Consumption 240W Temperature range 5 ~ 35°C (Operating) Size 308 (W) x 86 (H) x 252 (D) mm (Not including protruding parts) • Please refer to the following figure. Weight (mass) 2.6 kg Ports RGB input: RGB IN1 ..D-sub 15pin mini x1 RGB IN2 ..D-sub 15pin mini x1 RGB output: RGB OUT D-sub 15pin mini x1 Communication port: CONTROL ............D-sub 9pin x1 USB ....................... USB(B) x1 Video input: COMPONENT VIDEO Y ............................... RCA x1 CB/PB ....................... RCA x 1 CR/PR ...................... RCA x 1 S-Video ................................ 1 Video .................................... 1 Audio input: AUDIO IN1 ...... Stereo mini x1 AUDIO IN2 ...... Stereo mini x1 Audio output: AUDIO OUT ... Stereo mini x1 49 50Specifications Specifications (continued) [unit: mm] 89 219 308 Accessories Accessories Accessories ...............................................................Part Number UHB lamp, 165W ..................................................................78-6969-9790-3 Air Filter ................................................................................78-8118-9376-3 Power cord (US) ...................................................................78-8118-8102-4 Power cord (UK) ...................................................................78-8118-8101-6 Power cord (Europe) ............................................................78-8118-8103-2 VGA cable ............................................................................78-8118-8708-8 Remote control .....................................................................78-8118-9185-8 Soft case ..............................................................................78-8118-9194-0 Base .....................................................................................78-8118-9378-9 Filter cover bottom-up use ....................................................78-8118-9377-1 Not included with Basic Packet ................................Part Number Ceiling mount .......................................................................78-6969-9694-7 Adjustble height suspension .................................................78-6969-9698-8 Shipping case .......................................................................78-6969-9717-6 RCA Video cable ..................................................................78-8118-8482-0 S-Video cable .......................................................................78-8118-3238-1 RCA component cable ..........................................................78-8118-8843-3 RS-232C control cable .........................................................78-8118-9192-4 Stereo mini-cable .................................................................78-8118-8846-6 UHB cable ............................................................................78-8118-9057-9 Mac adapter .........................................................................78-8118-3308-2 Soft rolling luggage case ......................................................78-6969-9716-8 Soft side case with shoulder strup ........................................78-6969-9715-0 Ultra value warranty S55(US only) .......................................78-6969-9787-9 Ultra value warranty X45(US only) .......................................78-6969-9788-7 Ultra value warranty X55(US only) .......................................78-6969-9790-3 Deluxe Mouse Emulation Kit ................................................78-6969-9233-4 How to Order Please order these parts through your dealer, or contact 3M Customer Service at the following number : In U.S. or Canada : 1-800-328-1371 In other locations, contact your local 3M sales office. 51 Let us help you make the most of your next presentation. We offer everything from presentation supplies to tips for better meetings. And we're the only transparency manufacturer that offers a recycling program for your used transparencies. For late-breaking news, handy reference and free product samples, call us toll-free in the continental United States and Canada, 24 hours a day, or visit our Internet Website. 3M Austin Center Building A145-5N-01 6801 River Place Blvd. Austin, TX 78726-9000 3M Canada P.O. Box 5757 London, Ontario N6A 4T1 3M Mexico, S.A. de C.V. Apartado Postal 14-139 Mexico, D.F. 07000 Mexico 3M Mexico, S.A. de C.V. Apartado Postal 14-139 Mexico, D.F. 07000 Mexico 3M Europe Boulevard de l'Oise 95006 Cerge Pontoise Cedex France © 3M 2004 78-6970-9389-2 Rev. A 3M Europe Boulevard de l'Oise 95006 Cerge Pontoise Cedex France © 3M 2004 78-6970-9389-2 Rev. A 3M Europe Boulevard de l'Oise 95006 Cerge Pontoise Cedex France © 3M 2004 78-6970-9389-2 Rev. A (DN00741 - S55/X45/X55_OG_ENG) Intended Use Before operating this machine, please read this entire manual thoroughly. The 3MTM Multimedia Projectors are designed, built, and tested for use indoors, using 3M lamps, 3M ceiling mount hardware, and nominal local voltages. The use of other replacement lamps, outdoor operation, or different voltages has not been tested and could damage the projector peripheral equipment and/or create a potentially unsafe operating condition. 3M Multimedia projectors and Wall Display Systems are designed to operate in a normal office environment. • 16 ̊ to 29 ̊C (60 ̊ to 85 ̊ F) • 10- 80 %RH (without condensation) • 0- 1828 m (0-6000 feet) above sea level The ambient operating environment should be free of airborne smoke, grease, oil and other contaminates that can affect the operation or performance of the projector. Use of this product in adverse conditions will void the product warranty.

FREE ENGLISH PDF

OPERATING INSTRUCTIONS

USER GUIDE - USER MANUAL

OWNER GUIDE - OWNER MANUAL

REFERENCE GUIDE - REFERENCE MANUAL

INSTRUCTION GUIDE - INSTRUCTION MANUAL