SUPERO SUPERSERVER 5018A-MLTN4 (01) PDF MANUAL

Report any errors on this page in the comment box below.

PDF OCR Transcript: SUPER SUPERSERVER ® ® 5018A-MLTN4 Revision 1.0b The information in this User’s Manual has been carefully reviewed and is believed to be accurate. The vendor assumes no responsibility for any inaccuracies that may be contained in this document, makes no commitment to update or to keep current the information in this manual, or to notify any person or organization of the updates. Please Note: For the most up-to-date version of this manual, please see our web site at www.supermicro.com. Super Micro Computer, Inc. ("Supermicro") reserves the right to make changes to the product described in this manual at any time and without notice. This product, including software and docu- mentation, is the property of Supermicro and/or its licensors, and is supplied only under a license. Any use or reproduction of this product is not allowed, except as expressly permitted by the terms of said license. IN NO EVENT WILL SUPERMICRO BE LIABLE FOR DIRECT, INDIRECT, SPECIAL, INCIDENTAL, SPECULATIVE OR CONSEQUENTIAL DAMAGES ARISING FROM THE USE OR INABILITY TO USE THIS PRODUCT OR DOCUMENTATION, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. IN PARTICULAR, SUPERMICRO SHALL NOT HAVE LIABILITY FOR ANY HARDWARE, SOFTWARE, OR DATA STORED OR USED WITH THE PRODUCT, INCLUDING THE COSTS OF REPAIRING, REPLACING, INTEGRATING, INSTALLING OR RECOVERING SUCH HARDWARE, SOFTWARE, OR DATA. Any disputes arising between manufacturer and customer shall be governed by the laws of Santa Clara County in the State of California, USA. The State of California, County of Santa Clara shall be the exclusive venue for the resolution of any such disputes. Super Micro's total liability for all claims will not exceed the price paid for the hardware product. FCC Statement: This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environ- ment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the manufacturer’s instruction manual, may cause harmful interference with radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case you will be required to correct the interference at your own expense. California Best Management Practices Regulations for Perchlorate Materials: This Perchlorate warn- ing applies only to products containing CR (Manganese Dioxide) Lithium coin cells. “Perchlorate Material-special handling may apply. See www.dtsc.ca.gov/hazardouswaste/perchlorate” WARNING: Handling of lead solder materials used in this product may expose you to lead, a chemical known to the State of California to cause birth defects and other repro- ductive harm. Manual Revision 1.0a Release Date: October 14, 2014 Unless you request and receive written permission from Super Micro Computer, Inc., you may not copy any part of this document. Information in this document is subject to change without notice. Other products and companies referred to herein are trademarks or registered trademarks of their respective companies or mark holders. Copyright © 2014 by Super Micro Computer, Inc. All rights reserved. Printed in the United States of America Preface Preface About This Manual This manual is written for professional system integrators and PC technicians. It provides information for the installation and use of the SuperServer 5018A-MLTN4. Installation and maintenance should be performed by experienced technicians only. The SuperServer 5018A-MLTN4 is a 1U rackmount server based on the SC512L- 200B server chassis and the Super A1SAM-2550F motherboard. Please refer to our web site for updates on supported processors. Manual Organization Chapter 1: Introduction The first chapter provides a checklist of the main components included with the server system and describes the main features of the A1SAM-2550F motherboard and the SC512L-200B chassis. Chapter 2: Server Installation This chapter describes the steps necessary to install the SuperServer 5018A-MLTN4 into a rack and check out the server configuration prior to powering up the system. If your server was ordered without memory, this chapter will refer you to the ap- propriate section of the manual for installation. Chapter 3: System Interface Refer to this chapter for details on the system interface, which includes the functions and information provided by the control panel on the chassis as well as other LEDs located throughout the system. Chapter 4: Standardized Warning Statements You should thoroughly familiarize yourself with this chapter for a general overview of safety precautions that should be followed when installing and servicing the SuperServer 5018A-MLTN4. iii SUPERSERVER 5018A-MLTN4 User's Manual Chapter 5: Advanced Motherboard Setup Chapter 5 provides detailed information on the A1SAM-2550F motherboard, in- cluding the locations and functions of connectors, headers and jumpers. Refer to this chapter when adding or removing main memory and when reconfiguring the motherboard. Chapter 6: Advanced Chassis Setup Refer to Chapter 6 for detailed information on the SC512L-200B chassis. You should follow the procedures given in this chapter when installing, removing or reconfigur- ing Serial ATA or peripheral drives and when replacing system power supply units and cooling fans. Chapter 7: BIOS The BIOS chapter includes an introduction to BIOS and provides detailed informa- tion on running the CMOS Setup Utility. Appendix A: BIOS POST Error Codes Appendix B: System Specifications iv Preface Notes v SUPERSERVER 5018A-MLTN4 User's Manual Table of Contents Chapter 1 Introduction 1-1 Overview ......................................................................................................... 1-1 1-2 Motherboard Features ..................................................................................... 1-2 Processors ...................................................................................................... 1-2 Memory ........................................................................................................... 1-2 SATA ..............................................................................................................1-2 PCI Expansion Slots ....................................................................................... 1-2 I/O Ports .......................................................................................................... 1-2 1-3 Server Chassis Features ................................................................................ 1-3 System Power ................................................................................................. 1-3 SATA Subsystem ............................................................................................. 1-3 Control Panel .................................................................................................. 1-3 Cooling System ............................................................................................... 1-3 1-4 Contacting Supermicro .................................................................................... 1-5 Chapter 2 Server Installation 2-1 Overview ......................................................................................................... 2-1 2-2 Unpacking the System .................................................................................... 2-1 2-3 Preparing for Setup ......................................................................................... 2-1 Choosing a Setup Location ............................................................................. 2-1 2-4 Warnings and Precautions .............................................................................. 2-2 Rack Precautions ............................................................................................ 2-2 Server Precautions .......................................................................................... 2-2 Rack Mounting Considerations ....................................................................... 2-3 Ambient Operating Temperature ................................................................ 2-3 Reduced Airflow ......................................................................................... 2-3 Mechanical Loading ................................................................................... 2-3 Circuit Overloading ..................................................................................... 2-3 Reliable Ground ......................................................................................... 2-3 2-5 Installing the System into a Rack ................................................................... 2-4 Identifying the Sections of the Rack Rails (Optional) ..................................... 2-4 Installing the Inner Rail Extension .................................................................. 2-5 Installing the Outer Rails to the Rack ............................................................. 2-6 Installing the Chassis into a Rack................................................................... 2-8 Mid-Mount Telco Rack..................................................................................... 2-9 Installing the Chassis into a Rack in Mid-Mount Position .............................. 2-9 vi Table of Contents Chapter 3 System Interface 3-1 Overview ......................................................................................................... 3-1 3-2 Control Panel Buttons ..................................................................................... 3-1 Reset ............................................................................................................... 3-1 Power .............................................................................................................. 3-1 3-3 Control Panel LEDs ........................................................................................ 3-2 Overheat/Fan Fail LED ................................................................................... 3-2 NIC2 ................................................................................................................ 3-2 NIC1 ................................................................................................................ 3-2 HDD ................................................................................................................. 3-3 Power .............................................................................................................. 3-3 Chapter 4 Standardized Warning Statements for AC Systems 4-1 About Standardized Warning Statements ....................................................... 4-1 Warning Definition ........................................................................................... 4-1 Installation Instructions .................................................................................... 4-4 Circuit Breaker ................................................................................................ 4-5 Power Disconnection Warning ........................................................................ 4-6 Equipment Installation ..................................................................................... 4-8 Restricted Area ................................................................................................ 4-9 Battery Handling ............................................................................................ 4-10 Redundant Power Supplies .......................................................................... 4-12 Backplane Voltage ........................................................................................ 4-13 Comply with Local and National Electrical Codes ........................................ 4-14 Product Disposal ........................................................................................... 4-15 Hot Swap Fan Warning ................................................................................. 4-16 Power Cable and AC Adapter ...................................................................... 4-18 Chapter 5 Advanced Motherboard Setup 5-1 Handling the Motherboard .............................................................................. 5-1 Precautions ..................................................................................................... 5-1 Unpacking ....................................................................................................... 5-2 5-2 Motherboard Installation .................................................................................. 5-2 5-3 Connecting Cables .......................................................................................... 5-3 Connecting Data Cables ................................................................................. 5-3 Connecting Power Cables .............................................................................. 5-3 Connecting the Control Panel ......................................................................... 5-3 5-4 Rear I/O Ports ................................................................................................. 5-4 5-5 Onboard Processor and Heatsink ................................................................... 5-5 5-6 Installing Memory Modules ............................................................................. 5-5 Installing & Removing DIMMs ......................................................................... 5-5 vii SUPERSERVER 5018A-MLTN4 User's Manual Memory Support ......................................................................................... 5-6 Memory Population Guidelines ....................................................................... 5-6 5-7 Adding PCI Cards ........................................................................................... 5-7 5-8 Motherboard Details ........................................................................................ 5-8 Motherboard Layout ........................................................................................ 5-8 A1SAM-2550F Quick Reference Table ........................................................... 5-8 5-9 Connector Definitions ................................................................................... 5-10 ATX Power Connector .............................................................................. 5-10 Power Button ........................................................................................... 5-10 Reset Button ............................................................................................. 5-10 Power Fail LED ........................................................................................ 5-10 Overheat (OH)/Fan Fail/PWR Fail/UID LED .............................................5-11 NIC2 (LAN2) LED ......................................................................................5-11 HDD LED ...................................................................................................5-11 Power On LED ..........................................................................................5-11 NMI Button ............................................................................................... 5-12 Fan Headers ............................................................................................. 5-12 Chassis Intrusion ...................................................................................... 5-12 Universal Serial Bus (USB) ...................................................................... 5-12 Serial Ports ............................................................................................... 5-13 Power SMB (I2C) Connector .................................................................... 5-13 Onboard Speaker (SP1) ........................................................................... 5-13 Power LED/Speaker ................................................................................. 5-13 DOM Power Connector ............................................................................ 5-14 TPM/Port 80 Header ................................................................................ 5-14 Overheat LED/Fan Fail ............................................................................ 5-14 LAN3/LAN4 LED Indication Header ......................................................... 5-14 LAN (Ethernet) Ports ................................................................................ 5-15 Unit Identifier Switch/UID LED Indicators ................................................ 5-15 System Management Bus Header ........................................................... 5-16 Standby Power ......................................................................................... 5-16 Overheat LED Header .............................................................................. 5-16 5-10 Jumper Settings ............................................................................................ 5-17 Explanation of Jumpers ................................................................................ 5-17 CMOS Clear ............................................................................................. 5-17 LAN1/LAN2 Enable/Disable ..................................................................... 5-17 VGA Enable/Disable ................................................................................. 5-18 Watch Dog ................................................................................................ 5-18 BMC Enable ............................................................................................5-18 viii Table of Contents PCI-E Slot SMB Enable ........................................................................... 5-18 BIOS Recovery Enable ............................................................................ 5-19 USB Wake-Up Enable .............................................................................. 5-19 5-11 Onboard Indicators ........................................................................................ 5-19 LAN Port LEDs ......................................................................................... 5-19 IPMI Dedicated LAN LEDs ....................................................................... 5-19 Onboard Power LED ............................................................................... 5-20 Overheat/PWR Fail/Fan Fail LED ............................................................ 5-20 Unit Identification LED .............................................................................. 5-20 5-12 SATA Ports .................................................................................................... 5-21 SATA Ports ............................................................................................... 5-21 5-13 Installing Software ......................................................................................... 5-22 SuperDoctor® 5 ............................................................................................ 5-23 5-14 Onboard Battery ............................................................................................ 5-24 Chapter 6 Advanced Chassis Setup 6-1 Static-Sensitive Devices .................................................................................. 6-1 Precautions ..................................................................................................... 6-1 Unpacking ....................................................................................................... 6-1 6-2 Control Panel .................................................................................................. 6-2 6-3 Removing the Chassis Cover ......................................................................... 6-2 6-4 System Fan ..................................................................................................... 6-3 6-5 Installing Hard Drives ...................................................................................... 6-5 6-6 PCI Slot Setup ................................................................................................ 6-7 6-7 Power Supply .................................................................................................. 6-8 Power Supply Failure ...................................................................................... 6-8 Chapter 7 BIOS 7-1 Introduction ...................................................................................................... 7-1 7-2 Main Setup ...................................................................................................... 7-2 7-3 Advanced Setup Configurations...................................................................... 7-4 7-4 IPMI Configuration ........................................................................................ 7-20 7-4 Event Logs .................................................................................................... 7-22 7-5 Security Settings ........................................................................................... 7-24 7-6 Boot Settings ................................................................................................. 7-27 7-7 Save & Exit ................................................................................................... 7-29 Appendix A BIOS Post Error Codes Appendix B System Specifications ix SUPERSERVER 5018A-MLTN4 User's Manual Notes x Chapter 1: Introduction Chapter 1 Introduction 1-1 Overview The SuperServer 5018A-MLTN4 is comprised of two main subsystems: the SC512L- 200B 1U chassis and the A1SAM-2550F motherboard. Please refer to our web site for information on operating systems that have been certified for use with the SuperServer 5018A-MLTN4 (www.supermicro.com). In addition to the motherboard and chassis, various hardware components have been included with the system, as listed below: • One 10-cm PWM blower fan (FAN-0038L4) Note: For your system to work properly, please follow the links below to download all necessary drivers/utilities and the user’s manual for your server. • Supermicro product manuals: http://www.supermicro.com/support/manuals/ • Product drivers and utilities: ftp://ftp.supermicro.com • Product safety info: http://super-dev/about/policies/safety_information.cfm • If you have any questions, please contact our support team at: support@supermicro.com 1-1 SUPERSERVER 5018A-MLTN4 User's Manual 1-2 Motherboard Features At the heart of the SuperServer 5018A-MLTN4 lies the A1SAM-2550F, an embed- ded processor motherboard. Below are the main features of the A1SAM-2550F. See Figure 1-1 for a block diagram of the motherboard. Processors The A1SAM-2550F supports a single Intel® C2000 Tri-Gate 22nm SoC (System-on- a Chip) Series 4-core processor in an FCBGA 1283 package (embedded processor). Memory The A1SAM-2550F has four DIMM slots that can support up to 64GB of DDR3- 1600/1333 Unbuffered (UDIMM) ECC/Non-ECC memory. DIMMs of the same size and speed should be used. See Chapter 5 for details. SATA A SATA controller is integrated into the chipset to provide a six-port Serial ATA sub- system (4x SATA 2.0 and 2x SATA 3.0 ports). The SATA drives are hot-swappable units.PCI Expansion Slots The motherboard includes one PCI-Express 2.0 x8 and one PCI-Express 2.0 x4 slot. The system supports one PCI-Express 2.0 x8 card with the use of an optional installed riser card. I/O Ports The I/O ports include a COM port, a VGA port, four USB 2.0 ports, four Gb LAN (NIC) ports and a dedicated IPMI LAN port. 1-2 Chapter 1: Introduction 1-3 Server Chassis Features The following is a general outline of the main features of the SC512L-200B chassis. System Power The SC512L-200B chassis includes a single 200W power supply. SATA Subsystem The SC512L-200B chassis was designed to support two internal 3.5" SATA hard drives. Control Panel The SC512L-200B's control panel provides important system monitoring and control information. LEDs indicate power on, network activity, hard disk drive activity and system overheat conditions. The control panel also includes a main power button and a system reset button. Cooling System The SC512L-200B chassis features one 10-cm PWM blower fan, which connects to a chassis fan header on the motherboard. Fan speed is controlled by IPMI. 1-3 SUPERSERVER 5018A-MLTN4 User's Manual Figure 1-1. A1SAM-2550F Motherboard: System Block Diagram Note: This is a general block diagram. Please see Chapter 5 for details. FLASH 128Mb SPI Rangeley A2 A1 PCIE 2.0 x 8 SLOT PCIE x 8 PEG [8..15]PCIE 2.0 x 4 SLOT CHB CHB PCIE 2.0 x 4 SLOT PCIE x 4 USB 2.0 USB Hub PD720114 USB 2.0 USB 1 USB 2.0 LPC NI AVOTON SOC VGA FAN x 3 TPM HDR CHA CHA DIMMA1 DIMMB2 DJPCIE1 JPCIE2 IMMA2 (Optional) JPCIE3 B2 B1 DPEG [4..7] IMMB1HEADER USB + TYPE-A REAR REAR + PD720114 USB Hub SATA GEN3 RJ45 SATA 3.0 SATA GEN2 SATA 3.0 SATA 2.0 SATA 2.0 RTL8211E REAR REAR USB 2.0 SATA 2.0 SATA 2.0 REAR REAR USB 0 GbE LAN PCIE x 1 PEG [0] AST2400USB [2:3] 0Ohm TX/RX (debug) LPC UART1 UART2 COM1 10BASE-T/100BASE-T/1000BASE-T SGMII x 4 88E1543 LAN3 LAN1 + LAN4 LAN2 COM2 1-4 Chapter 1: Introduction 1-4 Contacting Supermicro Headquarters Address: Super Micro Computer, Inc. 980 Rock Ave. San Jose, CA 95131 U.S.A. Tel: +1 (408) 503-8000 Fax: +1 (408) 503-8008 Email: marketing@supermicro.com (General Information) support@supermicro.com (Technical Support) Website: www.supermicro.com Europe Address: Super Micro Computer B.V. Het Sterrenbeeld 28, 5215 ML 's-Hertogenbosch, The Netherlands Tel: +31 (0) 73-6400390 Fax: +31 (0) 73-6416525 Email: sales@supermicro.nl (General Information) support@supermicro.nl (Technical Support) rma@supermicro.nl (Customer Support) Website: www.supermicro.nl Asia-Pacific Address: Super Micro Computer, Inc. 3F, No. 150, Jian 1st Rd. Zhonghe Dist., New Taipei City 235 Taiwan (R.O.C) Tel: +886-(2) 8226-3990 Fax: +886-(2) 8226-3992 Email: support@supermicro.com.tw Website: www.supermicro.com.tw 1-5 SUPERSERVER 5018A-MLTN4 User's Manual Notes 1-6 Chapter 2: Server Installation Chapter 2 Server Installation 2-1 Overview This chapter provides a quick setup checklist to get your SuperServer 5018A-MLTN4 up and running. Following the steps in the order given should enable you to have the system operational within a minimal amount of time. This quick setup assumes that your system has come to you with the processor and memory preinstalled. If your system is not already fully integrated with a motherboard, processor, system memory etc., please turn to the chapter or section noted in each step for details on installing specific components. 2-2 Unpacking the System You should inspect the box the server was shipped in and note if it was damaged in any way. If the server itself shows damage, you should file a damage claim with the carrier who delivered it. Decide on a suitable location for the rack unit that will hold the server. It should be situated in a clean, dust-free area that is well ventilated. Avoid areas where heat, electrical noise and electromagnetic fields are generated. You will also need it placed near a grounded power outlet. Read the Rack and Server Precautions in the next section. 2-3 Preparing for Setup The 5018A-MLTN4 may have shipped with an optional rack mount kit to install the system into the rack. Follow the steps in the order given to complete the installation process in a minimal amount of time. Please read this section in its entirety before you begin the installation procedure outlined in the sections that follow. Choosing a Setup Location • Leave enough clearance in front of the rack to enable you to open the front door completely (~25 inches) and approximately 30 inches of clearance in the back of the rack to allow for sufficient airflow and ease in servicing.This product is for installation only in a Restricted Access Location (dedicated equipment rooms, service closets and the like). 2-1 SUPERSERVER 5018A-MLTN4 User's Manual • This product is not suitable for use with visual display work place devices acccording to §2 of the the German Ordinance for Work with Visual Display Units. 2-4 Warnings and Precautions Rack Precautions • Ensure that the leveling jacks on the bottom of the rack are fully extended to the floor with the full weight of the rack resting on them. • In single rack installation, stabilizers should be attached to the rack. In multiple rack installations, the racks should be coupled together. • Always make sure the rack is stable before extending a component from the rack. • You should extend only one component at a time - extending two or more si- multaneously may cause the rack to become unstable. Server Precautions • Review the electrical and general safety precautions in Chapter 4. • Determine the placement of each component in the rack before you install the rails. • Install the heaviest server components on the bottom of the rack first, and then work up. • Use a regulating uninterruptible power supply (UPS) to protect the server from power surges, voltage spikes and to keep your system operating in case of a power failure. • Allow the hot plug SATA drives and power supply modules to cool before touch- ing them. • Always keep the rack's front door and all panels and components on the servers closed when not servicing to maintain proper cooling. 2-2 Chapter 2: Server Installation Rack Mounting Considerations Ambient Operating Temperature If installed in a closed or multi-unit rack assembly, the ambient operating tempera- ture of the rack environment may be greater than the ambient temperature of the room. Therefore, consideration should be given to installing the equipment in an environment compatible with the manufacturer’s maximum rated ambient tempera- ture (Tmra). Reduced Airflow Equipment should be mounted into a rack so that the amount of airflow required for safe operation is not compromised. Mechanical Loading Equipment should be mounted into a rack so that a hazardous condition does not arise due to uneven mechanical loading. Circuit Overloading Consideration should be given to the connection of the equipment to the power supply circuitry and the effect that any possible overloading of circuits might have on overcurrent protection and power supply wiring. Appropriate consideration of equipment nameplate ratings should be used when addressing this concern. Reliable Ground A reliable ground must be maintained at all times. To ensure this, the rack itself should be grounded. Particular attention should be given to power supply connec- tions other than the direct connections to the branch circuit (i.e. the use of power strips, etc.).Warning! To prevent bodily injury when mounting or servicing this unit in a rack, you must take special precautions to ensure that the system remains stable. The following guidelines are provided to ensure your safety: • This unit should be mounted at the bottom of the rack if it is the only unit in the rack. • When mounting this unit in a partially filled rack, load the rack from the bottom to the top with the heaviest component at the bottom of the rack. • If the rack is provided with stabilizing devices, install the stabilizers before mounting or servicing the unit in the rack. 2-3 SUPERSERVER 5018A-MLTN4 User's Manual 2-5 Installing the System into a Rack This section provides information on installing the SuperServer 5018A-MLTN4 into a rack unit with the optional rack rails. There are a variety of rack units on the market, which may mean the assembly procedure will differ slightly. You should also refer to the installation instructions that came with the rack unit you are using. Identifying the Sections of the Rack Rails (Optional) The chassis package includes two rack rail assemblies in the rack mounting kit. Each assembly consists of two sections: an inner fixed chassis rail that secures directly to the server chassis, and an outer fixed rack rail that secures directly to the rack itself. The SC512F comes with "chassis ears" that allow the chassis to use generic rails. Figure 2-1. Identifying the Sections of the Rack Rails (Right side rail shown) Inner Rails Chassis Ears Outer Rails 2-4 Chapter 2: Server Installation Installing the Inner Rail Extension The SC512F includes chassis ears that you must remove before installing the rails. Removing the Chassis Ears 1. Locate and remove the three screws holding the chassis ear in place. 2. Repeat step on with the other chassis ear. Figure 2-2. Installing Rear Inner Chassis Rails Installing the Inner Rails 1. Place the inner rail on the side of the chassis aligning the hooks of the chas- sis with the rail holes. 2. Slide the rail toward the front of the chassis to secure the rail in place. 3. Secure the chassis with four screws. 4. Repeat steps 1-3 for the other inner rail extension. 2-5 SUPERSERVER 5018A-MLTN4 User's Manual Warning: do not pick up the server with the front handles. They are de- signed to pull the system from a rack only. Secure to the Rear of the Rack Attach Outer Rack Rails Together Secure to the Front of the Rack Figure 2-3. Assembling the Outer Rails Installing the Outer Rails to the Rack Installing the Outer Rails 1. Attach the short bracket to the outside of the long bracket. You must align the pins with the slides. Also, both bracket ends must face the same direction. 2. Adjust both the short and long brackets to the proper distance so that the rail fits snugly into the rack. 3. Secure the long bracket to the front side of the outer rail with two M5 screws and the short bracket to the rear side of the outer rail with three M5 screws. Use a washer with each screw. 4. Repeat steps 1-4 for the left outer rail. 2-6 Chapter 2: Server Installation Stability hazard. The rack stabilizing mechanism must be in place, or the rack must be bolted to the floor before you slide the unit out for servicing. Failure to stabilize the rack can cause the rack to tip over. 2-7 13 12 13 SCALE 0.380 Figure 2-4. Installing the Outer Rails to the Server Rack Note: this figure is for illustrative purposes only. Always install servers to the bot- tom of a rack first. SUPERSERVER 5018A-MLTN4 User's Manual Figure 2-5. Installing the Chassis into a Rack Installing the Chassis into a Rack Installing the Chassis 1. Confirm that the inner rails are attached to the chassis. Also, confirm that the outer rails are installed on the rack. 2. Align chassis rails with the front of the rack rails. 3. Slide the chassis rails into the rack rails, keeping the pressure even on both sides (It may be necessary to depress the locking tabs when inserting). When the server has been pushed completely into the rack, you should hear the locking tabs "click" into the locked position. 4. (Optional) Insert and tightening the thumbscrews that hold the front of the server to the rack. Note: this figure is for illustrative purposes only. Always install servers to the bot- tom of a rack first. 2-8 Chapter 2: Server Installation Mid-Mount Telco Rack The SC512.supports Telco rack installation. The SC512 chassis compact design allows the chassis to be installed into a Telco rack without the use of rails. Installing the Chassis into a Rack in Mid-Mount Position Instaling into a Mid-Mount Position Rack 1. If it is necessary to install the chassis in a mid-mount Telco rack, remove the chassis rails and the chassis ears (if the ears are installed at the front of the chassis). 2. Locate the three screw holes in the middle of the chassis and secure the ears to the chassis with three flat head screws. Make sure the screws are secure, but do not over tighten the screws. 2-9 Place Chassis Ears Here Figure 2-6. Placing the Chassis Ears for Telco Rack Installation SUPERSERVER 5018A-MLTN4 User's Manual Figure 2-7. Installing the Server into a Telco RackSCALE 1 1. Hold the chassis in the telco rack and screw the chassis to the rack using the three screw holes located in the chassis ears. 2. The chassis is held in place by the chassis ears and does not slide in and out of place. Note: this figure is for illustrative purposes only. Always install servers to the bot- tom of a rack first. 2-10 Chapter 3: System Interface Chapter 3 System Interface 3-1 Overview There are several LEDs on the control panel as well as others on the SATA drive carriers to keep you constantly informed of the overall status of the system as well as the activity and health of specific components. There are also two buttons on the chassis control panel and an on/off switch on the power supply. This chapter explains the meanings of all LED indicators and the appropriate response you may need to take. 3-2 Control Panel Buttons There are two push-buttons located on the front of the chassis: a reset button and a power on/off button. Reset The reset button reboots the system. Power This is the main power button, which is used to apply or turn off the main system power. Turning off system power with this button removes the main power but keeps standby power supplied to the system. 3-1 SUPERSERVER 5018A-MLTN4 User's Manual 3-3 Control Panel LEDs The control panel located on the front of the SC512L-200B chassis has five LEDs. These LEDs provide you with critical information related to different parts of the system. This section explains what each LED indicates when illuminated and any corrective action you may need to take. Overheat/Fan Fail LED When this LED flashes it indicates a fan failure. When continuously on (not flashing) it indicates an overheat condition, which may be caused by cables obstructing the airflow in the system or the ambient room temperature being too warm. Check the routing of the cables and make sure all fans are present and operating normally. You should also check to make sure that the chassis covers are installed. Finally, verify that the heatsinks are installed properly. This LED will remain flashing or on as long as the overheat condition exists. NIC2 Indicates network activity on LAN2 when flashing. NIC1 Indicates network activity on LAN1 when flashing. 2 1 3-2 Power Indicates power is being supplied to the system's power supply units. This LED should normally be illuminated when the system is operating. HDD Channel activity for all HDDs. This light indicates SATA drive activity on the 5018A- MLTN4 when flashing. Chapter 3: System Interface 3-3 SUPERSERVER 5018A-MLTN4 User's Manual Notes 3-4 Chapter 4: Warning Statements for AC Systems Chapter 4 Standardized Warning Statements for AC Systems 4-1 About Standardized Warning Statements The following statements are industry standard warnings, provided to warn the user of situations which have the potential for bodily injury. Should you have questions or experience difficulty, contact Supermicro's Technical Support department for assistance. Only certified technicians should attempt to install or configure components. Read this appendix in its entirety before installing or configuring components in the Supermicro chassis. These warnings may also be found on our web site at http://www.supermicro.com/ about/policies/safety_information.cfm. Warning! This warning symbol means danger. You are in a situation that could cause bodily injury. Before you work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar with standard practices for preventing accidents. Warning Definition 警告の定義 この警告サインは危険を意味します。 人身事故につながる可能性がありますので、いずれの機器でも動作させる前に、 電気回路に含まれる危険性に注意して、標準的な事故防止策に精通して下さい。 此警告符号代表危险。 您正处于可能受到严重伤害的工作环境中。在您使用设备开始工作之前,必须充分 意识到触电的危险,并熟练掌握防止事故发生的标准工作程序。请根据每项警告结 尾的声明号码找到此设备的安全性警告说明的翻译文本。 此警告符號代表危險。 您正處於可能身體可能會受損傷的工作環境中。在您使用任何設備之前,請注意觸 電的危險,並且要熟悉預防事故發生的標準工作程序。請依照每一注意事項後的號 碼找到相關的翻譯說明內容。 4-1 SUPERSERVER 5018A-MLTN4 User's Manual Warnung WICHTIGE SICHERHEITSHINWEISE Dieses Warnsymbol bedeutet Gefahr. Sie befinden sich in einer Situation, die zu Verletzungen führen kann. Machen Sie sich vor der Arbeit mit Geräten mit den Gefahren elektrischer Schaltungen und den üblichen Verfahren zur Vorbeugung vor Unfällen vertraut. Suchen Sie mit der am Ende jeder Warnung angegebenen Anweisungsnummer nach der jeweiligen Übersetzung in den übersetzten Sicherheitshinweisen, die zusammen mit diesem Gerät ausgeliefert wurden. BEWAHREN SIE DIESE HINWEISE GUT AUF. INSTRUCCIONES IMPORTANTES DE SEGURIDAD Este símbolo de aviso indica peligro. Existe riesgo para su integridad física. Antes de manipular cualquier equipo, considere los riesgos de la corriente eléctrica y familiarícese con los procedimientos estándar de prevención de accidentes. Al final de cada advertencia encontrará el número que le ayudará a encontrar el texto traducido en el apartado de traducciones que acompaña a este dispositivo. GUARDE ESTAS INSTRUCCIONES. IMPORTANTES INFORMATIONS DE SÉCURITÉ Ce symbole d'avertissement indique un danger. Vous vous trouvez dans une situation pouvant entraîner des blessures ou des dommages corporels. Avant de travailler sur un équipement, soyez conscient des dangers liés aux circuits électriques et familiarisez-vous avec les procédures couramment utilisées pour éviter les accidents. Pour prendre connaissance des traductions des avertissements figurant dans les consignes de sécurité traduites qui accompagnent cet appareil, référez-vous au numéro de l'instruction situé à la fin de chaque avertissement. CONSERVEZ CES INFORMATIONS. ןונקת תורהצה א הרהז ןה תואבה תורהצה א ינפמ שמתשמה תא ריהזהל תנמ לע ,היישעתה ינקת יפ לע תורהז הלבח ה וא תולאש שיו הדימב .תירשפא תיזיפ י ,יהשלכ היעבב תולקת רוציל שי הכימת תקלחמ םע רשק רידגהל וא ןיקתהל םיאשר דבלב םיכמסומ םיאנכט .ורקימרפוס לש תינכט תא ה .םיביכר אורקל שי .ורקימרפוס יזראמב םיביכרה תרדגה וא תנקתה ינפל ואולמב חפסנה תא 4-2 Warning Statements for AC Systems . ةیدسج ةباصا يف ببستت نأ نکمی ةلاح يف كنا رطخ ينعی زمرلا اذھ !ریذحت رئاودلا نع ةمجانلا رطاخملاب ملع یلع ن ،ک تادعم يأ یلع لمعت نأ لبق ةیئابرھکلا ثداوح يأ عوقو عنم ل ةیئاقولا تاس رامملاب ةیارد یلع ن کو اھتمجرت روثعلل ریذحت لک ةیاھن يف صوصنملا نایبلا مقر مدختسا 안전을 위한 주의사항 경고! 이 경고 기호는 위험이 있음을 알려 줍니다. 작업자의 신체에 부상을 야기 할 수 있는 상태에 있게 됩니다. 모든 장비에 대한 작업을 수행하기 전에 전기회로와 관련된 위험요소들을 확인하시고 사전에 사고를 방지할 수 있도록 표준 작업절차를 준수해 주시기 바랍니다. 해당 번역문을 찾기 위해 각 경고의 마지막 부분에 제공된 경고문 번호를 참조하십시오 BELANGRIJKE VEILIGHEIDSINSTRUCTIES Dit waarschuwings symbool betekent gevaar. U verkeert in een situatie die lichamelijk letsel kan veroorzaken. Voordat u aan enige apparatuur gaat werken, dient u zich bewust te zijn van de bij een elektrische installatie betrokken risico's en dient u op de hoogte te zijn van de standaard procedures om ongelukken te voorkomen. Gebruik de nummers aan het eind van elke waarschuwing om deze te herleiden naar de desbetreffende locatie. BEWAAR DEZE INSTRUCTIES 4-3 SUPERSERVER 5018A-MLTN4 User's Manual Installation Instructions Warning! Read the installation instructions before connecting the system to the power source. 設置手順書 システムを電源に接続する前に、設置手順書をお読み下さい。 警告将此系统连接电源前,请先阅读安装说明。 警告將系統與電源連接前,請先閱讀安裝說明。 Warnung Vor dem Anschließen des Systems an die Stromquelle die Installationsanweisungen lesen. ¡Advertencia! Lea las instrucciones de instalación antes de conectar el sistema a la red de alimentación. Attention Avant de brancher le système sur la source d'alimentation, consulter les directives d'installation. . חתמ רוקמל תכרעמה רוביח ינפל הנקתה תוארוה תא אורקל שי ةقاطلل ردصم ىلإ ماظنلا ليصوت لبق بيكرت لا تاداشرإ رقا 시스템을 전원에 연결하기 전에 설치 안내를 읽어주십시오. Waarschuwing Raadpleeg de installatie-instructies voordat u het systeem op de voedingsbron aansluit. 4-4 サーキット・ブレーカー この製品は、短絡(過電流)保護装置がある建物での設置を前提としています。 保護装置の定格が250 V、20 Aを超えないことを確認下さい。 警告此产品的短路(过载电流)保护由建筑物的供电系统提供,确保短路保护设备的额定电 流不大于250V,20A。 警告此產品的短路(過載電流)保護由建築物的供電系統提供,確保短路保護設備的額定電 流不大於250V,20A。 Warnung Dieses Produkt ist darauf angewiesen, dass im Gebäude ein Kurzschluss- bzw. Überstromschutz installiert ist. Stellen Sie sicher, dass der Nennwert der Schutzvorrichtung nicht mehr als: 250 V, 20 A beträgt. ¡Advertencia! Este equipo utiliza el sistema de protección contra cortocircuitos (o sobrecorrientes) del edificio. Asegúrese de que el dispositivo de protección no sea superior a: 250 V, 20 A. Attention Pour ce qui est de la protection contre les courts-circuits (surtension), ce produit dépend de l'installation électrique du local. Vérifiez que le courant nominal du dispositif de protection n'est pas supérieur à :250 V, 20 A. יכ אדוול שי .ילמשח רצק תעינמל םינבמב תנקתומה הנגה לע ךמתסמ הז רצומ 60VDC, 20A-מ רתוי אל אוה ילמשחה רצקה ינפמ ןגמה רישכמה يف اهتيبثت مت يتلا ةريصقلارئاودلا هم تيامحلا ثادعم ىلع دمتعي جتنملا اذه ىنبملا 20A, 250VDC :نم رثكأ سيل يئاقولا زاهجلا مييقت نأ نم دكأت Chapter 4: Warning Statements for AC Systems Circuit Breaker Warning! This product relies on the building's installation for short-circuit (overcurrent) protection. Ensure that the protective device is rated not greater than: 250 V, 20 A. 4-5 SUPERSERVER 5018A-MLTN4 User's Manual 경고! 이 제품은 전원의 단락(과전류)방지에 대해서 전적으로 건물의 관련 설비에 의존합니다. 보호장치의 정격이 반드시 250V(볼트), 20A(암페어)를 초과하지 않도록 해야 합니다. Waarschuwing Dit product is afhankelijk van de kortsluitbeveiliging (overspanning) van uw electrische installatie. Controleer of het beveiligde aparaat niet groter gedimensioneerd is dan 220V, 20A. Power Disconnection Warning Warning! The system must be disconnected from all sources of power and the power cord removed from the power supply module(s) before accessing the chassis interior to install or remove system components. 電源切断の警告 システムコンポーネントの取り付けまたは取り外しのために、シャーシー内部にアクセス するには、 システムの電源はすべてのソースから切断され、電源コードは電源モジュールから取り 外す必要があります。 警告在你打开机箱并安装或移除内部器件前,必须将系统完全断电,并移除电源线。 警告在您打開機殼安裝或移除內部元件前,必須將系統完全斷電,並移除電源線。 Warnung Das System muss von allen Quellen der Energie und vom Netzanschlusskabel getrennt sein, das von den Spg.Versorgungsteilmodulen entfernt wird, bevor es auf den Chassisinnenraum zurückgreift, um Systemsbestandteile anzubringen oder zu entfernen. 4-6 Chapter 4: Warning Statements for AC Systems ¡Advertencia! El sistema debe ser disconnected de todas las fuentes de energía y del cable eléctrico quitado de los módulos de fuente de alimentación antes de tener acceso el interior del chasis para instalar o para quitar componentes de sistema. Attention Le système doit être débranché de toutes les sources de puissance ainsi que de son cordon d'alimentation secteur avant d'accéder à l'intérieur du chassis pour installer ou enlever des composants de systéme.ילמשח קותינ ינפמ הרהזא !הרהזא למשחה תורוקמ לכמ תכרעמה תא קתנל שי ריסהל שיו קפסהמ ילמשחה לבכ תא נקתה ךרוצל זראמה לש ימינפה קלחל השיג ינפל ת רסה וא ת .םיביכר لصف بجی ماظنلا عیمج نم رداصم ةقاطلا ةلازإو ءابرھکلا كلس نم ةدحو دادما ةقاطلا لبق یلإ لوصولا ةیلخادلا قطانملا ل لکیھل ةلازإ وأ تیبثتل تانوکم زاھجلا 경고! 시스템에 부품들을 장착하거나 제거하기 위해서는 섀시 내부에 접근하기 전에 반드시 전원 공급장치로부터 연결되어있는 모든 전원과 전기코드를 분리해주어야 합니다. Waarschuwing Voordat u toegang neemt tot het binnenwerk van de behuizing voor het installeren of verwijderen van systeem onderdelen, dient u alle spanningsbronnen en alle stroomkabels aangesloten op de voeding(en) van de behuizing te verwijderen 4-7 SUPERSERVER 5018A-MLTN4 User's Manual Equipment Installation Warning! Only trained and qualified personnel should be allowed to install, replace, or service this equipment. 機器の設置 トレーニングを受け認定された人だけがこの装置の設置、交換、またはサービスを許可 されています。 警告只有经过培训且具有资格的人员才能进行此设备的安装、更换和维修。 警告只有經過受訓且具資格人員才可安裝、更換與維修此設備。 Warnung Das Installieren, Ersetzen oder Bedienen dieser Ausrüstung sollte nur geschultem, qualifiziertem Personal gestattet werden. ¡Advertencia! Solamente el personal calificado debe instalar, reemplazar o utilizar este equipo. Attention Il est vivement recommandé de confier l'installation, le remplacement et la maintenance de ces équipements à des personnels qualifiés et expérimentés. !הרהזא שר דבלב ךמסומ תווצ תא ףילחהל ,ןיקתהל יא .דויצה רובע תוריש תתל וא דויצה نیبردملاو و بیکرتل لادبتسا وأ ةمدخ زاھجلا اذھ حمسی نأ بجی طقف نیلھؤملا نیفظوملل 경고! 훈련을 받고 공인된 기술자만이 이 장비의 설치, 교체 또는 서비스를 수행할 수 있습니다. 4-8 Chapter 4: Warning Statements for AC Systems Waarschuwing Deze apparatuur mag alleen worden geïnstalleerd, vervangen of hersteld door geschoold en gekwalificeerd personeel. Restricted Area Warning! This unit is intended for installation in restricted access areas. A restricted access area can be accessed only through the use of a special tool, lock and key, or other means of security. (This warning does not apply to workstations). アクセス制限区域 このユニットは、アクセス制限区域に設置されることを想定しています。 アクセス制限区域は、特別なツール、鍵と錠前、その他のセキュリティの手段を用いての み出入りが可能です。 警告此部件应安装在限制进出的场所,限制进出的场所指只能通过使用特殊工具、锁和 钥匙或其它安全手段进出的场所。 警告此裝置僅限安裝於進出管制區域,進出管制區域係指僅能以特殊工具、鎖頭及鑰匙 或其他安全方式才能進入的區域。 Warnung Diese Einheit ist zur Installation in Bereichen mit beschränktem Zutritt vorgesehen. Der Zutritt zu derartigen Bereichen ist nur mit einem Spezialwerkzeug, Schloss und Schlüssel oder einer sonstigen Sicherheitsvorkehrung möglich. ¡Advertencia! Esta unidad ha sido diseñada para instalación en áreas de acceso restringido. Sólo puede obtenerse acceso a una de estas áreas mediante la utilización de una herramienta especial, cerradura con llave u otro medio de seguridad. Attention Cet appareil doit être installée dans des zones d'accès réservés. L'accès à une zone d'accès réservé n'est possible qu'en utilisant un outil spécial, un mécanisme de verrouillage et une clé, ou tout autre moyen de sécurité. 4-9 SUPERSERVER 5018A-MLTN4 User's Manual Battery Handling Warning! There is the danger of explosion if the battery is replaced incorrectly. Replace the battery only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufacturer's instructions תלבגומ השיג םע רוזא !הרהזא תרזעב תנתינ השיגה .השיג תלבגה םהב שיש םירוזאב הדיחיה תא ןיקתהל שי .)'דכו לוענמ ,חתפמ( דבלב החטבא ילכ . صيصخت ةدحولا هذھ يف اھبیکرتل قطانم ةروظحم مت صولا نکمی یلإ لو ةقطنم ةروظحم طقف مادختسا للاخ نم ،ةصاخ ةادأ وأ يأ لال ىرخأ ةلیسو ناملأ حاتفمو لفق 경고! 이 장치는 접근이 제한된 구역에 설치하도록 되어있습니다. 특수도구, 잠금 장치 및 키, 또는 기타 보안 수단을 통해서만 접근 제한 구역에 들어갈 수 있습니다. Waarschuwing Dit apparaat is bedoeld voor installatie in gebieden met een beperkte toegang. Toegang tot dergelijke gebieden kunnen alleen verkregen worden door gebruik te maken van speciaal gereedschap, slot en sleutel of andere veiligheidsmaatregelen. 電池の取り扱い 電池交換が正しく行われなかった場合、破裂の危険性があります。 交換する電池はメー カーが推奨する型、または同等のものを使用下さい。 使用済電池は製造元の指示に従 って処分して下さい。 警告电池更换不当会有爆炸危险。请只使用同类电池或制造商推荐的功能相当的电池更 换原有电池。请按制造商的说明处理废旧电池。 警告電池更換不當會有爆炸危險。請使用製造商建議之相同或功能相當的電池更換原有 電池。請按照製造商的說明指示處理廢棄舊電池。 4-10 Chapter 4: Warning Statements for AC Systems Warnung Bei Einsetzen einer falschen Batterie besteht Explosionsgefahr. Ersetzen Sie die Batterie nur durch den gleichen oder vom Hersteller empfohlenen Batterietyp. Entsorgen Sie die benutzten Batterien nach den Anweisungen des Herstellers. Attention Danger d'explosion si la pile n'est pas remplacée correctement. Ne la remplacer que par une pile de type semblable ou équivalent, recommandée par le fabricant. Jeter les piles usagées conformément aux instructions du fabricant. ¡Advertencia! Existe peligro de explosión si la batería se reemplaza de manera incorrecta. Reemplazar la batería exclusivamente con el mismo tipo o el equivalente recomendado por el fabricante. Desechar las baterías gastadas según las instrucciones del fabricante. !הרהזא תנכס תמייק ץוציפ .הניקת אל ךרדב הפלחוהו הדימב הללוסה לש ףילחהל שי גוסב הללוסה תא מ םאותה תרבח למומ ןרצי תצ . תוללוסה קוליס תושמושמה עצבל שי .ןרציה תוארוה יפל رطخ كانھ نم لادبتسا ةلاح يف راجفنا ةیراطبلا ةحیحص ریغ ةقیرطب كیلعف ةیراطبلا لادبتسا طقف عونلا سفنب اھلداعی ام وأ امک تصوأ ةعنصملا ةکرشلا ھب تایراطبلا نم صلخت ل اقفو ةلمعتسملا ةعناصلا ةکرشلا تامیلعت 경고! 배터리가 올바르게 교체되지 않으면 폭발의 위험이 있습니다. 기존 배터리와 동일하거나 제조사에서 권장하는 동등한 종류의 배터리로만 교체해야 합니다. 제조사의 안내에 따라 사용된 배터리를 처리하여 주십시오. Waarschuwing Er is ontploffingsgevaar indien de batterij verkeerd vervangen wordt. Vervang de batterij slechts met hetzelfde of een equivalent type die door de fabrikant aanbevolen wordt. Gebruikte batterijen dienen overeenkomstig fabrieksvoorschriften afgevoerd te worden. 4-11 SUPERSERVER 5018A-MLTN4 User's Manual Redundant Power Supplies Warnung Dieses Gerät kann mehr als eine Stromzufuhr haben. Um sicherzustellen, dass der Einheit kein trom zugeführt wird, müssen alle Verbindungen entfernt werden. ¡Advertencia! Puede que esta unidad tenga más de una conexión para fuentes de alimentación. Para cortar por completo el suministro de energía, deben desconectarse todas las conexiones. Attention Cette unité peut avoir plus d'une connexion d'alimentation. Pour supprimer toute tension et tout courant électrique de l'unité, toutes les connexions d'alimentation doivent être débranchées. Warning! This unit might have more than one power supply connection. All connections must be removed to de-energize the unit. 冗長電源装置 このユニットは複数の電源装置が接続されている場合があります。 ユニットの電源を切るためには、すべての接続を取り外さなければなりません。 警告此部件连接的电源可能不止一个,必须将所有电源断开才能停止给该部件供电。 警告此裝置連接的電源可能不只一個,必須切斷所有電源才能停止對該裝置的供電。 דחא קפסמ רתוי םייק םא !הרהזא ןקורל תנמ לע םירוביחה לכ תא ריסהל שי .קפס לש דחא רוביחמ רתוי שי הדחיל .הד י חיה תא 4-12 Chapter 4: Warning Statements for AC Systems . ةقاطلا دادما تادحوب تلااصتا ةدع زاهج لا اذهل نوكي دق ءابرهكلا نع ةدحو لا لسعل تلااصتلاا ةفاك ةلازإ بجي 경고! 이 장치에는 한 개 이상의 전원 공급 단자가 연결되어 있을 수 있습니다. 이 장치에 전원을 차단하기 위해서는 모든 연결 단자를 제거해야만 합니다. Waarschuwing Deze eenheid kan meer dan één stroomtoevoeraansluiting bevatten. Alle aansluitingen dienen verwijderd te worden om het apparaat stroomloos te maken. Backplane Voltage Warning! Hazardous voltage or energy is present on the backplane when the system is operating. Use caution when servicing. バックプレーンの電圧 システムの稼働中は危険な電圧または電力が、バックプレーン上にかかっています。 修理する際には注意ください。 警告当系统正在进行时,背板上有很危险的电压或能量,进行维修时务必小心。 警告當系統正在進行時,背板上有危險的電壓或能量,進行維修時務必小心。 Warnung Wenn das System in Betrieb ist, treten auf der Rückwandplatine gefährliche Spannungen oder Energien auf. Vorsicht bei der Wartung. ¡Advertencia! Cuando el sistema está en funcionamiento, el voltaje del plano trasero es peligroso. Tenga cuidado cuando lo revise. Attention Lorsque le système est en fonctionnement, des tensions électriques circulent sur le fond de panier. Prendre des précautions lors de la maintenance. 4-13 SUPERSERVER 5018A-MLTN4 User's Manual Comply with Local and National Electrical Codes ירוחאה לנפב חתמ !הרה זא ךלהמב רהזיהל שי .תכרעמה לועפת ןמזב ירוחאה לנפב חתמ תנכס תמייק .הדובעה ةحوللا یلع ةدوجوملا ةقاطلاوأ يئابرھکلا رایتلا نم رطخ كانھ زاھجلا اذھ ةمدخ دنع ارذح نک لمعی ماظنلا نوکی امدنع 경고! 시스템이 동작 중일 때 후면판 (Backplane)에는 위험한 전압이나 에너지가 발생 합니다. 서비스 작업 시 주의하십시오. Waarschuwing Een gevaarlijke spanning of energie is aanwezig op de backplane wanneer het systeem in gebruik is. Voorzichtigheid is geboden tijdens het onderhoud. Warning! Installation of the equipment must comply with local and national electrical codes. 地方および国の電気規格に準拠 機器の取り付けはその地方および国の電気規格に準拠する必要があります。 警告设备安装必须符合本地与本国电气法规。 警告設備安裝必須符合本地與本國電氣法規。 Warnung Die Installation der Geräte muss den Sicherheitsstandards entsprechen. ¡Advertencia! La instalacion del equipo debe cumplir con las normas de electricidad locales y nacionales. 4-14 Chapter 4: Warning Statements for AC Systems Attention L'équipement doit être installé conformément aux normes électriques nationales et locales. 경고! 현 지역 및 국가의 전기 규정에 따라 장비를 설치해야 합니다. Waarschuwing Bij installatie van de apparatuur moet worden voldaan aan de lokale en nationale elektriciteitsvoorschriften. Product Disposal 製品の廃棄 この製品を廃棄処分する場合、国の関係する全ての法律・条例に従い処理する必要が あります。 警告本产品的废弃处理应根据所有国家的法律和规章进行。 警告本產品的廢棄處理應根據所有國家的法律和規章進行。 Warnung Die Entsorgung dieses Produkts sollte gemäß allen Bestimmungen und Gesetzen des Landes erfolgen. יצראה למשחה יקוח םואית !הרהזא . םייצראהו םיימוקמה למשחה יקוחל תמאות תויהל תבייח דויצה תנקתה ةقلعتملا ةینطولاو ةیلحملا نیناوق لل لثتمی نأ بجی ةیئابرھکلا تادعملا بیکرت ءابرھکلاب Warning! Ultimate disposal of this product should be handled according to all national laws and regulations. 4-15 SUPERSERVER 5018A-MLTN4 User's Manual ¡Advertencia! Al deshacerse por completo de este producto debe seguir todas las leyes y reglamentos nacionales. Attention La mise au rebut ou le recyclage de ce produit sont généralement soumis à des lois et/ou directives de respect de l'environnement. Renseignez-vous auprès de l'organisme compétent. Waarschuwing De uiteindelijke verwijdering van dit product dient te geschieden in overeenstemming met alle nationale wetten en reglementen. Warning! The fans might still be turning when you remove the fan assembly from the chassis. Keep fingers, screwdrivers, and other objects away from the openings in the fan assembly's housing. רצומה קוליס !הרהזא .הנידמה יקוח ו תויחנהל םאתהב תויהל בייח הז רצומ לש יפוס קוליס ةینطولا حئاوللاو نیناوقلا عیمج ل اقفو ھعم لماعتلا يغبنی جتنملا اذھ نم يئاھنلا صلختلا دنع 경고! 이 제품은 해당 국가의 관련 법규 및 규정에 따라 폐기되어야 합니다. Hot Swap Fan Warning ファン・ホットスワップの警告 シャーシから冷却ファン装置を取り外した際、ファンがまだ回転している可能性がありま す。 ファンの開口部に、指、ドライバー、およびその他のものを近づけないで下さい。 警告当您从机架移除风扇装置,风扇可能仍在转动。小心不要将手指、螺丝起子和其他 物品太靠近风扇 4-16 Chapter 4: Warning Statements for AC Systems 警告當您從機架移除風扇裝置,風扇可能仍在轉動。小心不要將手指、螺絲起子和其他 物品太靠近風扇。 Warnung Die Lüfter drehen sich u. U. noch, wenn die Lüfterbaugruppe aus dem Chassis genommen wird. Halten Sie Finger, Schraubendreher und andere Gegenstände von den Öffnungen des Lüftergehäuses entfernt. ¡Advertencia! Los ventiladores podran dar vuelta cuando usted quite ell montaje del ventilador del chasis. Mandtenga los dedos, los destornilladores y todos los objetos lejos de las aberturas del ventilador Attention Il est possible que les ventilateurs soient toujours en rotation lorsque vous retirerez le bloc ventilateur du châssis. Prenez garde à ce que doigts, tournevis et autres objets soient éloignés du logement du bloc ventilateur. !הרהזא שי .םידבוע ןיידע םיררוואמהו ןכתי ,זראמהמ ררוואמה יקלח תא םיריסמ רשאכ ררוואמה ךותב םיחתפהמ םינוש הדובע ילכו תועבצאה תא חוטב קחרמ ל קיחרהל ءاقبإ بجی لکیھلا نم ةحورملا ةلتک ةلازإ دنعرودت لازت لا حوارملا نأ نکمملا نم يغاربلا تاکفم و عباصلأا . ةحورملا ةلتک يف تاحتفلا نع ادیعب ءایشلأا نم اھریغو 경고! 섀시로부터 팬 조립품을 제거할 때 팬은 여전히 회전하고 있을 수 있습니다. 팬 조림품 외관의 열려있는 부분들로부터 손가락 및 스크류드라이버, 다른 물체들이 가까이 하지 않도록 배치해 주십시오. Waarschuwing Het is mogelijk dat de ventilator nog draait tijdens het verwijderen van het ventilatorsamenstel uit het chassis. Houd uw vingers, schroevendraaiers en eventuele andere voorwerpen uit de buurt van de openingen in de ventilatorbehuizing. 4-17 SUPERSERVER 5018A-MLTN4 User's Manual Warning! When installing the product, use the provided or designated connection cables, power cables and AC adaptors. Using any other cables and adaptors could cause a malfunction or a fire. Electrical Appliance and Material Safety Law prohibits the use of UL or CSA -certified cables (that have UL/CSA shown on the code) for any other electrical devices than products designated by Supermicro only. Power Cable and AC Adapter 電源コードとACアダプター 製品を設置する場合、提供または指定された接続ケーブル、電源コードとACアダプター を使用下さい。 他のケーブルやアダプタを使用すると故障や火災の原因になることがあ ります。 電気用品安全法は、ULまたはCSA認定のケーブル(UL/CSEマークがコードに表 記)を Supermicroが指定する製品以外に使用することを禁止しています。 警告安装此产品时,请使用本身提供的或指定的连接线,电源线和电源适配器.使用其它线 材或适配器可能会引起故障或火灾。除了Supermicro所指定的产品,电气用品和材 料安全法律规定禁止使用未经UL或CSA认证的线材。(线材上会显示UL/CSA符号)。 警告安裝此產品時,請使用本身提供的或指定的連接線,電源線和電源適配器.使用其它線 材或適配器可能會引起故障或火災。除了Supermicro所指定的產品,電氣用品和材 料安全法律規定禁止使用未經UL或CSA認證的線材。(線材上會顯示UL/CSA符號)。 Warnung Bei der Installation des Produkts, die zur Verfügung gestellten oder benannt Anschlusskabel, Stromkabel und Netzteile. Verwendung anderer Kabel und Adapter kann zu einer Fehlfunktion oder ein Brand entstehen. Elektrische Geräte und Material Safety Law verbietet die Verwendung von UL-oder CSA-zertifizierte Kabel, UL oder CSA auf der Code für alle anderen elektrischen Geräte als Produkte von Supermicro nur bezeichnet gezeigt haben. ¡Advertencia! Al instalar el producto, utilice los cables de conexión previstos o designados, los cables y adaptadores de CA. La utilización de otros cables y adaptadores podría ocasionar un mal funcionamiento o un incendio. Aparatos Eléctricos y la Ley de Seguridad del Material prohíbe el uso de UL o CSA cables certificados que tienen UL o CSA se muestra en el código de otros dispositivos eléctricos que los productos designados por Supermicro solamente. 4-18 Chapter 4: Warning Statements for AC Systems Attention Lors de l'installation du produit, utilisez les bables de connection fournis ou désigné. L'utilisation d'autres cables et adaptateurs peut provoquer un dysfonctionnement ou un incendie. Appareils électroménagers et de loi sur la sécurité Matériel interdit l'utilisation de UL ou CSA câbles certifiés qui ont UL ou CSA indiqué sur le code pour tous les autres appareils électriques que les produits désignés par Supermicro seulement. אתמו םיילמשח מ י AC !הרהזא םימאתמו םיקפס ,םילבכב שמתשהל שי ,רצומה תא םיניקתמ רשאכ AC רשא וא הלקתל םורגל לוכי רחא םאתמ וא לבכ לכב שומיש .ךכ םשל וקפוסו ודעונ טב יקוחו למשח ירישכמב שומיש יקוח יפ לע .ילמשח רצק רוסיא םייק ,תוחי ב םיכמסומה םילבכב שמתשהל - UL ב וא - CSA לש דוק םהילע עיפומ ראשכ( UL/CSA ) רחא ילמשח רצומ לכ רובע .דבלב ורקימקרפוס ידי לע ןיוצ אלש بیکرت دنع مادختسا بجی زاھجلا و،لیصوتلا تلاباک ةیئابرھکلا تلاباکلا تلاوحمو ددرتملا رایتلا . نأ يأ مادختسا تلاباک تلاوحمو ىرخأ ببستی يف لطع ثودح قیرح وأ . يتلا كل اھریفوت مت جتنملا عم UL وأ CSA ةیئابرھکلا ةزھجلأا داومو نوناق ةملاسلا مادختسا رظحی تلاباکلا لبق نم ةدمتعم Supermicro ةزھجأ ىرخأ ةیئابرھک ریغ تاجتنملا ةنیعملا لبق نم يلأ (UL/CSA لمحت يتلا ةملاع ) 경고! 제품을 설치할 때에는 제공되거나 지정된 연결케이블과 전원케이블, AC어댑터를 사용해야 합니다. 그 밖의 다른 케이블들이나 어댑터들은 고장 또는 화재의 원인이 될 수 있습니다. 전기용품안전법 (Electrical Appliance and Material Safety Law)은 슈퍼마이크로에서 지정한 제품들 외에는 그 밖의 다른 전기 장치들을 위한 UL또는 CSA에서 인증한 케이블(전선 위에 UL/CSA가 표시)들의 사용을 금지합니다. Waarschuwing Bij het installeren van het product, gebruik de meegeleverde of aangewezen kabels, stroomkabels en adapters. Het gebruik van andere kabels en adapters kan leiden tot een storing of een brand. Elektrisch apparaat en veiligheidsinformatiebladen wet verbiedt het gebruik van UL of CSA gecertificeerde kabels die UL of CSA die op de code voor andere elektrische apparaten dan de producten die door Supermicro alleen. 4-19 SUPERSERVER 5018A-MLTN4 User's Manual Notes 4-20 Chapter 5: Advanced Motherboard Setup Chapter 5 Advanced Motherboard Setup This chapter covers the steps required to install the A1SAM-2550F motherboard into the SC813MFTQ-202CB chassis, connect the data and power cables and install add-on cards. All motherboard jumpers and connections are also described. A layout and quick reference chart are included in this chapter for your reference. Remember to completely close the chassis when you have finished working with the motherboard to better cool and protect the system. 5-1 Handling the Motherboard Electrostatic Discharge (ESD) can damage electronic com ponents. To prevent damage to any printed circuit boards (PCBs), it is important to handle them very carefully (see previous chapter). To prevent the A1SAM-2550F motherboard from bending, keep one hand under the center of the board to support it when handling. The following measures are generally sufficient to protect your equipment from electric static discharge. Precautions • Use a grounded wrist strap designed to prevent Electrostatic Discharge (ESD). • Touch a grounded metal object before removing any board from its antistatic bag. • Handle a board by its edges only; do not touch its components, peripheral chips, memory modules or gold contacts. • When handling chips or modules, avoid touching their pins. • Put the motherboard, add-on cards and peripherals back into their antistatic bags when not in use. • For grounding purposes, make sure your computer chassis provides excellent conductivity between the power supply, the case, the mounting fasteners and the motherboard. 5-1 SUPERSERVER 5018A-MLTN4 User's Manual Unpacking The motherboard is shipped in antistatic packaging to avoid electrical static dis- charge. When unpacking the board, make sure the person handling it is static protected. 5-2 Motherboard Installation This section explains the first step of physically mounting the A1SAM-2550F into the SC813MFTQ-202CB chassis. Following the steps in the order given will eliminate the most common problems encountered in such an installation. To remove the motherboard, follow the procedure in reverse order. Installing to the Chassis 1. Remove the screws from the rear lip of the chassis cover (see Figure 2-5). 2. Release the top cover by pushing it away from you until it stops. You can then lift the top cover from the chassis to gain full access to the inside of the server 3. Make sure that the I/O ports on the motherboard align properly with their respective holes in the I/O shield at the back of the chassis. 4. Carefully mount the motherboard to the motherboard tray by aligning the board holes with the raised metal standoffs that are visible in the chassis. 5. Insert screws into all the mounting holes on your motherboard that line up with the standoffs and tighten until snug (if you screw them in too tight, you might strip the threads). Note: Metal screws provide an electrical contact to the motherboard ground to provide a continuous ground for the system. Warning: To avoid damaging the motherboard and its components, do not apply any force greater than 8 lbs. per square inch when installing a screw into a mount- ing hole. 5-2 Chapter 5: Advanced Motherboard Setup 5-3 Connecting Cables Now that the motherboard is installed, the next step is to connect the cables to the board. These include the data cables for the peripherals and control panel and the power cables. Connecting Data Cables The cables used to transfer data from the peripheral devices have been carefully routed to prevent them from blocking the flow of cooling air that moves through the system from front to back. If you need to disconnect any of these cables, you should take care to keep them routed as they were originally after reconnecting them. The following data cables (with their locations noted) must remian connected. (See the layout on page 5-12 for connector locations.) • SATA drive cables (I-SATA0 ~ I-SATA3) • Control Panel cable (JF1) Connecting Power Cables The A1SAM-2550F has a 24-pin primary power supply connector (JPW1) for con- nection to the ATX power supply. See Section 5-9 for power connector pin defini- tions.Connecting the Control Panel JF1 contains header pins for various front control panel connectors. See Figure 5-1 for the pin locations of the various front control panel buttons and LED indicators. All JF1 wires have been bundled into a single ribbon cable to simplify this connec- tion. Make sure the red wire plugs into pin 1 as marked on the board. The other end connects to the Control Panel PCB board, located just behind the system status LEDs on the chassis. 5-3 SUPERSERVER 5018A-MLTN4 User's Manual Figure 5-1. Control Panel Header Pins 20 19 Ground NMI X X FP PWRLED 3.3 V HDD LED 3.3V Stby NIC1 Link LED 3.3V Stby NIC2 Link LED 3.3V Stby OH/Fan Fail/PWR Fail/ LED Cathode UID LED Cathode Power Fail LED 3.3V Ground Reset Reset Button Ground PWR2 1 5-4 Rear I/O Ports The I/O ports are located on the backplane of the motherboard. See Figure 5-2 below for the descriptions of the various I/O ports. Figure 5-2. Rear I/O Ports 4 1 25 Rear I/O Ports 1. COM1 Port 7. LAN1 Port 2. USB0 (USB 2.0) 8. LAN3 Port 3. USB1 (USB 2.0) 9. LAN2 Port 4. Dedicated IPMI LAN 10. LAN4 Port 5.USB2 (USB 2.0) 11. VGA Port 6. USB3 (USB 2.0) 12. UID Button Power Button 8 10 3 6 7911 112 1 5-4 Chapter 5: Advanced Motherboard Setup 5-5 Onboard Processor and Heatsink The A1SRi-2758F features an embedded Intel® C2000 Tri-Gate 22nm SoC (Sys- tem-on-a Chip) Series processor and attached heatsink. 5-6 Installing Memory Modules Note: Check the Supermicro web site for recommended memory modules. CAUTION Exercise extreme care when installing or removing DIMMs to prevent any possible damage. Installing & Removing DIMMs 1. Insert the desired number of DIMMs into the memory slots in the following order: DIMMA1, then DIMMB1, then DIMMA2, then DIMMB2. For best perfor- mance, please use DIMMs of the same type and same speed. See the DIMM installation charts on the following pages. 2. Push back the release tabs on the ends of a memory slot. Insert each DIMM vertically into its slot, paying attention to the notch along the bottom of the DIMM to prevent inserting it incorrectly. 3. Gently press down on the DIMM until it snaps into place in the slot. Repeat for all modules. 4. Reverse the steps above to remove a DIMM from the motherboard. Figure 5-3. DIMM Installation Notch Notch To Install: Insert module vertically and press down until it snaps into place. Pay attention Front View to the alignment notch at the bottom. To Remove: Use your thumbs to gently push the re- Release Tab Note: Notch should Release Tab align with the receptive lease tabs near both key point on the slot. ends of the module. This should release it from the slot. Top View of DDR3 Slot 5-5 SUPERSERVER 5018A-MLTN4 User's Manual Memory Support The A1SAM-2550F motherboard supports up to 64GB of DDR3-1600/1333 Unbuf- fered (UDIMM) ECC/Non-ECC memory. For the latest memory updates, please refer to the Supermicro website. Memory Population Guidelines Please follow the table below when populating the DIMM slots. Unbuffered (UDIMM) DDR3 Memory DIMM Slots per Channel DIMMs per Channel DIMM Type POR Speeds Memory Population Sequence 2 1 Unbuffered DDR3 DIMM 1600,1333 A1, B1 (2 DIMMs) 2 2 Unbuffered DDR3 DIMM 1600,1333 A1, B1, A2, B2 (4 DIMMs) Note: Use memory modules of the same type, speed, frequency and size. SoC Processor 5-6 Chapter 5: Advanced Motherboard Setup Note: Due to memory allocation to system devices, the amount of memory that remains available for operational use will be reduced when 4 GB of RAM is used. The reduction in memory availability is disproportional. See the following table for details. Possible System Memory Allocation & Availability System Device Size 5-7 Physical Memory Remaining (Available) (4 GB Total System Memory) Firmware Hub flash memory (System BIOS) 1 MB 3.99 Local APIC 4 KB 3.99 Area Reserved for the chipset 2 MB 3.99 I/O APIC (4 Kbytes) 4 KB 3.99 PCI Enumeration Area 1 256 MB 3.76 PCI Express (256 MB) 256 MB 3.51 PCI Enumeration Area 2 (if needed) -Aligned on 256-MB boundary- 512 MB 3.01 VGA Memory 16 MB 2.85 TSEG 1 MB 2.84 Memory available to OS and other applications 2.84 5-7 Adding PCI Cards With the optional RSC-RR1U-E8 riser card installed into a PCI-E slot, the 5018A- MLTN4 can support a full-height half-length PCI Express expansion card. Refer to Chapter 6 Section 7 for details. SUPERSERVER 5018A-MLTN4 User's Manual 5-8 Motherboard Details Motherboard Layout Figure 5-5. A1SAM-2550F Layout JPI2C1 JL1 USB0/1 BUZZER USB 2/3 LED3 FPCTRL LAN1/LAN3 DIMMA1 USB4/5 LED7 JPK1 SP1 JUIDB1 JVGA1 COM2 COM1 JPG1 A1SAM/A1SRM Series Rev. 1.01 JSD1 BMC PHY JBR1 JPUSB1 IPMI_LAN BATTERY JLAN2 JLAN1 JBT1 DCPU1 SLOT4 PCI-E 2.0 X4 CPU1 SLOT6 PCI-E 2.0 X8 JI2C1 JI2C2 JIPMB1 IMMB1 BIOS SoC Processor USB6 PWRI2C JBAT1 LED8 JTPM1 JF1 JD1 JPB1 JWD1A1SAM-2550F Quick Reference Table LED Description State/Status LED3 Power LED Green: System Power On LED7 UID Switch LED Blue: On Unit Identified LED8 Overheat/PWR/Fan Fail LED Solid On: Overheat Blinking: Power Fail or Fan Fail JPW1 I-SATA5 I-SATA1I-SATA4 I-SATA0 1 I-SATA3FAN3 JOH1 I-SATA2 FAN3 Note: Jumpers not noted are for test purposes only. 5-8 LAN2/LAN4 LAN3/4 LED DIMMB2 DIMMA2 JSTBY1 FAN1 Chapter 5: Advanced Motherboard Setup Jumper Description Default JBR1 BIOS Recovery Enable/Disable Pins 1-2 (Normal) JBT1 CMOS Clear Off (Normal) JI2C1/JI2C2 SMB to PCI-Exp. Slots Off (Disabled) JPB1 BMC Enable/Disable Pins 1-2 (Enabled) JPG1 VGA Enable/Disable Pins 1-2 (Enabled) JPL1 LAN Ports Enable/Disable Pins 1-2 (Enabled) JPUSB1 USB Wake Enable/Disable Pins 1-2 (Enabled) JWD1 Watch Dog Pins 1-2 (Reset) Connector Description Battery Onboard Battery (JBAT1) COM1/COM2 COM1/COM2 Port Headers FAN1-FAN3 System Cooling Fans JD1 Power LED/Speaker Header JF1 Front Panel Control Header JIPMB1 4-pin External SMbus I2C Header JL1 Chassis Intrusion Header JOH1 Overheat LED Header JPI2C1 Power Supply System Management Bus (SMBus) I2C Header JPK1 LAN3/LAN4 LED Indication Header JPW1 24-pin ATX Power Connector JSD1 SATA DOM (Device On Module) Power Connector JSTBY1 5V Standby Power Connector JTPM1 Trusted Platform Module (TPM)/Port 80 Connector JUIDB1 Unit Identifier (UID) Switch LAN1/3, LAN2/4 Gigabit Ethernet (RJ45) Ports 1/3, 2/4 IPMI-LAN Dedicated IPMI LAN for IPMI 2.0 Interface I-SATA0-I-SATA5 (Intel) Serial ATA Ports 0-5 (CPU1) Slot4 PCI-E 2.0 x4 slot (CPU1) Slot6 PCI-E 2.0 x8 slot SP1 Internal Speaker/Buzzer USB 0/1, 2/3 Backpanel USB 2.0 Ports 0/1, 2/3 USB 4/5 Front Panel Accessible USB 2.0 Headers 5-9 SUPERSERVER 5018A-MLTN4 User's Manual 5-9 Connector Definitions ATX Power Connector The 24-pin ATX power supply con- nector (JPW1) provides power to the motherboard. See the table on the right for pin definitions. Reset Button The Reset Button connection is located on pins 3 and 4 of JF1 and attaches to the reset switch on the computer chassis. See the table on the right for pin definitions. ATX Power 24-pin Connector Pin Definitions Pin# Definition Pin # Definition 13 +3.3V 1 +3.3V 14 -12V 2 +3.3V 15 COM 3 COM 16 PS_ON 4 +5V 17 COM 5 COM 18 COM 6 +5V 19 COM 7 COM 20 Res (NC) 8 PWR_OK 21 +5V 9 5VSB 22 +5V 10 +12V 23 +5V 11 +12V 24 COM 12 +3.3V Power Button The Power Button connection is on Power Button Pin Definitions pins 1 and 2 of JF1. This header Pin# Definition should be connected to the chassis 1 Signal power button. See the table on the 2 +3V Standby right for pin definitions. Reset Button Pin Definitions Pin# Definition 3 Reset 4 Ground Power Fail LED The Power Fail LED connection is located on pins 5 and 6 of JF1. Re- fer to the table on the right for pin definitions. PWR Fail LED Pin Definitions Pin# Definition 5 3.3V 6 Signal 5-10 Chapter 5: Advanced Motherboard Setup Overheat (OH)/Fan Fail/PWR Fail/ UID LED Connect an LED cable to pins 7 and 8 of Front Control Panel to use the Overheat/Fan Fail/Power Fail and UID LED connections. The Red LED on pin 7 provides warnings of over- heat, fan failure or power failure. The Blue LED on pin 8 works as the front panel UID LED indicator. The Red LED takes precedence over the Blue LED by default. Refer to the table on the right for pin definitions. 5-11 OH/Fan Fail/ PWR Fail/Blue_UID LED Pin Definitions Pin# Definition 7 Blue_UID LED 8 OH/Fan Fail/Power Fail Cathode NIC2 (LAN2) LED LAN1/LAN2 LED The LED connections for LAN2 are Pin Definitions on pins 9 and 10 of JF1. Attach LAN Pin# Definition LED cables to display network activ- 9/11 3.3V Standby ity. See the table on the right for pin 10/12 NIC Link LED definitions. HDD LED The HDD LED connection is located on pins 13 and 14 of JF1. Attach the Power On LED The Power On LED connector is lo- cated on pins 15 and 16 of JF1. This connection is used to provide LED indication of power being supplied to the system. See the table on the right for pin definitions. HDD LED Pin Definitions hard drive LED cable here to display Pin# Definition disk activity (for any hard drives on the 13 3.3V Standby system). See the table on the right for 14 HDD Active pin definitions Power LED Pin Definitions Pin# Definition 15 3.3V 16 Power LED SUPERSERVER 5018A-MLTN4 User's Manual NMI Button The non-maskable interrupt button header is located on pins 19 and 20 of JF1. Refer to the table on the right for pin definitions. Chassis Intrusion The Chassis Intrusion header is des- ignated JL1. See the board layout for the location of JL1 and the table on the right for pin definitions. NMI Button Pin Definitions Pin# Definition 19 Control 20 Ground Fan Headers There are three fan headers on the A1SAM-2550F. All are 4-pin fans but Fan Header are backward compatible with tradi- Pin Definitions tional 3-pin fans. Fan speed control, Pin# Definition however, is available for 4-pin fans 1 Ground (Black) only (via BMC). See the table on the 2 2.5A/+12V (Red) right for pin definitions. 3 Tachometer 4 PWM Control Note: the fans on the A1SAM-2550F are not hot-swappable. Chassis Intrusion Pin Definitions Pin# Definition 1 Intrusion Input 2 Ground Universal Serial Bus (USB) There are four Universal Serial Bus ports located on the I/O backpanel (USB01/, USB2/3) and an additional header located on the motherboard. The header, labeled USB4/5, as well as USB 6, a Type A port, can be used to provide front side USB access (cables not included). See the tables on the right for pin definitions. Back Panel USB0/1, 2/3 Pin Definitions Pin # Definition Pin # Definition 1 +5V 1 +5V 2 USB_PN1 2 USB_PN0 3 USB_PP1 3 USB_PP0 4 Ground 5 Ground USB Headers Pin Definitions (USB0/1, USB4) USB4/6 Pin # Definition USB5 Pin # Definition 1 +5V 1 +5V 2 PO- 2 PO- 3 PO+ 3 PO+ 4 Ground 4 Ground 5 No connection 5 Key 5-12 Chapter 5: Advanced Motherboard Setup Serial Ports Serial Port Pin Definitions Two serial ports are included on the Pin # Definition Pin # Definition motherboard: COM1 is located on the 1 DCD 6 DSR I/O backpanel and COM2 is a header 2 RXD 7 RTS (located near the onboard buzzer) for 3 TXD 8 CTS front access support. See the table on the right for pin definitions. 4 DTR 9 RI 5 Ground 10 NC Note: Pin 10 is included on the header but not on the port. NC indicates no connection. Power SMB (I2C) Connector Power System Management Bus (I2C) Connector (JPI2C1) monitors power supply, fan and system temperatures. See the table on the right for pin definitions. 5-13 PWR SMB Pin Definitions Pin# Definition 1 Clock 2 Data 3 PWR Fail 4 Ground 5 +3.3V Onboard Speaker (SP1) The onboard speaker provides au- dible indications for various beep codes. See the table on the right for pin definitions. Internal Buzzer Pin Definition Pin# Definitions Pin 1 Pos. (+) Beep In Pin 2 Neg. (-) Alarm Speaker Power LED/Speaker On JD1 header, pins 1-3 are used for power LED indication, and pins 4-7 are for the speaker. Connect pins (4-7) of JD1 with a cable to use the external speaker. If you wish to use the onboard speaker, close pins 6-7 with a jumper (Default). See the tables on the right for pin definitions. PWR LED Connector Pin Definitions Pin Setting Definition Pin 1 Anode (+) Pin2 Cathode (-) Pin3 NA Speaker Connector Pin Settings Pin Setting Definition Pins 4-7 External Speaker Pins 6-7 Internal Speaker (Default) SUPERSERVER 5018A-MLTN4 User's Manual DOM Power Connector A power connector for SATA DOM (Disk On Module) devices is located at JSD1. Connect an appropriate cable here to provide power support for your Serial Link DOM devices. DOM PWR Pin Definitions Pin# Definition 1 +5V 2 Ground 3 Ground TPM/Port 80 Header A Trusted Platform Module/Port 80 header is located at JTPM1 to provide TPM support and Port 80 connection. Use this header to enhance system performance and data security. See the table on the right for pin definitions. TPM/Port 80 Header Pin Definitions 1 LCLK 2 GND 3 LFRAME# 4 <(KEY) data-preserve-html-node="true"> 5 LRESET# 6 +5V (X) 7 LAD 3 8 LAD 2 9 +3.3V 10 LAD1 11 LAD0 12 GND 13 SMB_CLK4 14 SMB_DAT4 15 +3V_DUAL 16 SERIRQ Pin # Definition Pin # Definition 17 GND 18 CLKRUN# (X) 19 LPCPD# 20 LDRQ# (X) Overheat LED/Fan Fail Pin# Definition The JOH1 header is used to connect an LED indicator to provide warnings of chassis overheating and fan failure. This LED will blink when a fan failure occurs. Refer to the tables on right for pin definitions. Overheat LED Pin Definitions 1 5vDC 2 OH Active OH/Fan Fail/PWR Fail LED Status (Red LED) State Message Off Normal Solid Overheat Blinking Fan Fail LAN3/LAN4 LED Indication Header Connect an appropriate cable to the LAN3/4 LED indication header lo- cated at JPK1 to indicate activity on the LAN3/4 ports. (LAN1/LAN2 LED indicator connections are located on JF1.) 5-14 Chapter 5: Advanced Motherboard Setup 5-15 LAN Port Pin Definitions Pin# Definition Pin# Definition LAN (Ethernet) Ports 1 P2V5SB 10 SGND Four Gigabit Ethernet ports 2 TD0+ 11 Act LED (LAN1/2/3/4) are provided on the 3 TD0- 12 P3V3SB motherboard. These ports accept 4 TD1+ 13 Link 100 LED RJ45 type cables. The A1SAM-2550F (Yellow, +3V3SB) also includes a dedicated IPMI LAN 5 TD1- 14 Link 1000 LED (Yellow, +3V3SB) port above the rear USB ports to pro- 6 TD2+ 15 Ground vide KVM support for IPMI 2.0. 7 TD2- 16 Ground 8 TD3+ 17 Ground 9 TD3- 18 Ground Unit Identifier Switch/UID LED Indicators A Unit Identifier button (JUIDB), a backplane LED indicator and a front panel UID header are provided on the motherboard. The UID button is located next to the VGA port on the backplane. The rear UID LED indicator (LED1) is located next to the UID but- ton. The front panel UID LED header is located at pins 7/8 of JF1. Connect a cable to pin 8 on JF1 for the front panel UID LED connection. When you press the UID button, both the rear UID LED and the front panel UID LED will turn on. Press the UID button again to turn off both LEDs. These UID indicators provide easy identification of a system that may be in need of service. Note: UID can also be triggered via IPMI on the motherboard. For more information on IPMI, please refer to the IPMI User's Guide posted on our website: http://www.supermicro.com. UID Button Pin# Definition 1 Ground 2 Ground 3 Ground 4 Button In UID LED Status Color/State OS Status Blue: On Windows OS Unit Identified Blue: Blinking Linux OS Unit Identified SUPERSERVER 5018A-MLTN4 User's Manual System Management Bus Header A System Management Bus header for IPMI 2.0 is located at JIPMIB1. Connect the appropriate cable here to use the IPMI I2C connection on your system. SMBus Header Pin Definitions Pin# Definition 1 Data 2 Ground 3 Clock 4 No Connection Standby Power The 5V Standby Power header is lo- cated at JSTBY1 on the motherboard. Standby Power Pin Definitions Pin# Definition 1 +5V Standby 2 Ground 3 Wake-up Overheat LED Pin Definitions Overheat LED Header Pin Definition The JOH1 header is used to connect 1 5vDC an LED indicator to provide warnings 2 OH Active of chassis overheating and fan failure. This LED will blink when a fan failure occurs. Refer to the tables on right for pin definitions. OH/Fan Fail/PWR Fail LED Status (Red LED) State Definition Off Normal Solid Overheat Flashing Fan Fail 5-16 Chapter 5: Advanced Motherboard Setup 5-10 Jumper Settings Explanation of Jumpers To modify the operation of the mother- board, jumpers can be used to choose between optional settings. Jumpers create shorts between two pins to change the function of the connector. Pin 1 is identified with a square solder pad on the printed circuit board. See the motherboard layout pages for jumper locations. Note: On a two-pin jumper, "Closed" means the jumper is on both pins and "Open" means the jumper is either on only one pin or completely removed. CMOS Clear 3 2 1 3 2 1 Connector Pins Jumper Setting JBT1 is used to clear CMOS (which will also clear any passwords). Instead of pins, this jumper consists of contact pads to prevent accidentally clearing the contents of CMOS. To clear CMOS, 1. First power down the system and unplug the power cord(s). 2. With the power disconnected, short the CMOS pads with a metal object such as a small screwdriver. 3. Remove the screwdriver (or shorting device). 4. Reconnect the power cord(s) and power on the system Note: Do not use the PW_ON connector to clear CMOS. 5-17 LAN1/LAN2 Enable/Disable Change the setting of jumper JPL1 to enable or disable LAN ports on the motherboard. See the table on the right for jumper settings. The default setting is enabled. LAN1/2 Enable/Disable Jumper Settings Jumper Setting Definition Pins 1-2 Enabled Pins 2-3 Disabled SUPERSERVER 5018A-MLTN4 User's Manual VGA Enable/Disable JPG1 allows you to enable or disable the VGA port. The default position is on pins 1 and 2 to enable VGA. See the table on the right for jumper settings. VGA Enable/Disable Jumper Settings Jumper Setting Definition Pins 1-2 Enabled Pins 2-3 Disabled Watch Dog JWD1 enables the Watch Dog func- tion, a system monitor that takes action when a software application freezes the system. Jumping pins 1-2 will have WD reboot the system if a program freezes. Jumping pins 2-3 will gener- ate a non-maskable interrupt for the program that has frozen. See the table on the right for jumper settings. Watch Dog must also be enabled in BIOS. Watch Dog Jumper Settings Jumper Setting Definition Pins 1-2 Reset Pins 2-3 NMI Open Disabled BMC Enable Jumper JPB1 allows you to enable the embedded BMC (Baseboard Manage- ment Controller) to provide IPMI 2.0 support. See the table on the right for jumper settings. The default setting is enabled. Note: when Watch Dog is enabled, the user must write their own application software to disable the Watch Dog Timer. BMC Enable Jumper Settings Jumper Setting Definition Pins 1-2 BMC Enabled Pins 2-3 Disabled PCI-E Slot SMB Enable Use jumpers I2C1/I2C2 to enable PCI PCI Slot_SMB Enable SMB (System Management Bus) sup- Jumper Settings port to improve system management Jumper Setting Definition for the onboard PCI-E slots. The de- Closed Enabled fault setting is disabled. See the table Open (Default) Disabled on the right for jumper settings. 5-18 Chapter 5: Advanced Motherboard Setup BIOS Recovery Enable Close pins 1 and 2 of jumper JBR1 for BIOS recovery. The default setting is on pins 1 and 2 for normal operation. See the table on the right for jumper settings. 5-19 BIOS Recovery Enable Jumper Settings Jumper Setting Definition Pins 1-2 Normal Pins 2-3 BIOS Recovery USB Wake-Up Enable Close pins 1/2 of jumper JPUSB1 to "wake-up" the system by pressing a key on the USB keyboard or by clicking the USB mouse connected front acces- sible USB 4/5 or USB6. JPUSB1 is in conjunction with the USB Wake-Up function in the BIOS. Enable both the jumper and the BIOS setting to enable this function. Default setting is Normal. 5-11 Onboard Indicators LAN Port LEDs The Ethernet ports each have two LEDs. The yellow LED indicates activ- ity when blinking while the other LED may be green, amber or off to indicate the speed of the connection. See the table on the right for the functions as- sociated with the connection speed LED. USB Wake_UP Enable Jumper Settings Jumper Setting Definition Pins 1-2 USB Wake_up Enable Pins 2-3 Normal Link LED Activity LED LAN LED (Connection Speed Indicator) LED Color Definition Off No Connection or 10 Mb/s Green 10 Gb/s Amber 1 Gb/s IPMI Dedicated LAN LEDs The IPMI LAN port has two LEDs as well. The amber LED on the right indicates activity, while the green LED on the left indicates the speed of the connection. See the table at right for more information. LAN 1/LAN 2 IPMI LAN Link LED Activity LED IPMI IPMI LAN Link LAN LED (Left) & (X8ST3-F) Activity LED (Right) LED Color/State Definition Link (Left) Green: Solid 100 Mbps Activity (Right) Amber: Blink- ing Active SUPERSERVER 5018A-MLTN4 User's Manual Onboard Power LED An Onboard Power LED is located at LED3 on the motherboard. When this LED is on, the system is on. Be sure to turn off the system and unplug the power cord before removing or install- ing components. See the table at right for more information. ACPI S1 State Overheat/PWR Fail/Fan Fail LED An onboard Overheat/Power Failure/ Fan Failure LED is located at LED8. See the table on the right for more information. Overheat/PWR Fail/Fan Fail LED Settings Color/State Definition Solid Overheat Blinking PWR Fail or Fan Fail Unit Identification LED A rear UID LED indicator (LED7) is located next to the Unit Identifier (UID) button on the I/O backplane. The front panel UID LED is located at pin 7 of the Front Control Panel at JF1. Connect a cable to pin 7 on JF1 for front panel UID LED indication. When you press the UID button, both the rear UID LED and the front panel UID LED indicators will be turned on. Press the UID button again to turn off both LED indicators. These LEDs provide easy identification of a system unit that may be in need of service. Note: UID can also be triggered via IPMI on the motherboard. For more information on IPMI, please refer to the IPMI User's Guide posted on our Web- site at http://www.supermicro.com. UID LED Status Color/State OS Status Blue: On Windows OS Unit Identified Blue: Blinking Onboard PWR LED Indicator LED States LED Color Definition Off System Off (PWR cable not connected) Green System On Green: Flashing Quickly Green: Flashing Quickly Linux OS Unit Identified Linux OS Unit Identified 5-20 Chapter 5: Advanced Motherboard Setup 5-12 SATA Ports SATA Port Pin Definitions SATA Ports Pin # Definition Six SATA ports are included on the 1 Ground motherboard. I-SATA 0/1 are SATA 3.0 2 TXP ports and I-SATA2-I-SATA5 are SATA 3 TXN 2.0 ports. See the table on the right for 4 Ground pin definitions. 5 RXN 6 RXP 7 Ground 5-21 SUPERSERVER 5018A-MLTN4 User's Manual 5-13 Installing Software The Supermicro ftp site contains drivers and utilities for your system at ftp://ftp. supermicro.com. Some of these must be installed, such as the chipset driver. After accessing the ftp site, go into the CDR_Images directory and locate the ISO file for your motherboard. Download this file to create a CD/DVD of the drivers and utilities it contains. (You may also use a utility to extract the ISO file if preferred.) Another option is to go to the Supermicro Website at http://www.supermicro.com/ products/. Find the product page for your motherboard here, where you may down- load individual drivers and utilities. After creating a CD/DVD with the ISO files, insert the disk into the CD/DVD drive on your system and the display shown in Figure 5-6 should appear. Figure 5-6. Driver/Tool Installation Display Screen Note: Click the icons showing a hand writing on paper to view the readme files for each item. Click the computer icons to the right of these items to install each item (from top to the bottom) one at a time. After installing each item, you must re-boot the system before moving on to the next item on the list. The bottom icon with a CD on it allows you to view the entire contents. 5-22 Chapter 5: Advanced Motherboard Setup SuperDoctor® 5 The Supermicro SuperDoctor 5 is a program that functions in a command-line or web-based interface in Windows and Linux operating systems. The program moni- tors system health information such as CPU temperature, system voltages, system power consumption, fan speed, and provides alerts via email or Simple Network Management Protocol (SNMP). SuperDoctor 5 comes in local and remote management versions and can be used with Nagios to maximize your system monitoring needs. With SuperDoctor 5 Man- agement Server (SSM Server), you can remotely control power on/off and reset chassis intrusion for multiple systems with SuperDoctor 5 or IPMI. SD5 Manage- ment Server monitors HTTP, FTP, and SMTP services to optimize the efficiency of your operation. Note: The default User Name and Password for SuperDoctor 5 is admin / admin. Figure 5-7. SuperDoctor 5 Interface Display Screen (Health Information) Note: The SuperDoctor 5 program and User’s Manual can be downloaded from the Supermicro web site at http://www.supermicro.com/products/nfo/sms_sd5.cfm. 5-23 SUPERSERVER 5018A-MLTN4 User's Manual 5-14 Onboard Battery Please handle used batteries carefully. Do not damage the battery in any way; a damaged battery may release hazardous materials into the environment. Do not discard a used battery in the garbage or a public landfill. Please comply with the regulations set up by your local hazardous waste management agency to dispose of your used battery properly. Figure 5-8. Installing the Onboard Battery OR 5-24 Chapter 6: Advanced Chassis Setup Chapter 6 Advanced Chassis Setup This chapter covers the steps required to install components and perform mainte- nance on the SC512L-200B chassis. For component installation, follow the steps in the order given to eliminate the most common problems encountered. If some steps are unnecessary, skip ahead to the step that follows. Tools Required: The only tool you will need to install components and perform maintainance is a Philips screwdriver. 6-1 Static-Sensitive Devices Electrostatic Discharge (ESD) can damage electronic com ponents. To prevent damage to any printed circuit boards (PCBs), it is important to handle them very carefully. The following measures are generally sufficient to protect your equipment from ESD discharge. Precautions • Use a grounded wrist strap designed to prevent static discharge. • Touch a grounded metal object before removing any board from its antistatic bag. • Handle a board by its edges only; do not touch its components, peripheral chips, memory modules or gold contacts. • When handling chips or modules, avoid touching their pins. • Put the motherboard, add-on cards and peripherals back into their antistatic bags when not in use. • For grounding purposes, make sure your computer chassis provides excellent conductivity between the power supply, the case, the mounting fasteners and the motherboard. Unpacking The motherboard is shipped in antistatic packaging to avoid static damage. When unpacking the board, make sure the person handling it is static protected. 6-1 SUPERSERVER 5018A-MLTN4 User's Manual Figure 6-1. Chassis Front View Figure 6-2. Chassis Rear View Power Supply I/O Ports 6-2 Control Panel The control panel (located on the front of the chassis) must be connected to the JF1 connector on the motherboard to provide you with system control buttons and status indicators. These wires have been bundled together in a ribbon cable to simplify the connection. The LEDs inform you of system status. See Chapter 3 for details on the LEDs and the control panel buttons. Details on JF1 can be found in Chapter 5. 6-3 Removing the Chassis Cover Removing the Chassis Cover 1. Power down the system and disconnect the power cord from the from the rear of the power supply. 2. Place the chassis on a stable hard surface. 3. Remove the screws holding the chassis cover in place. 4. Apply pressure to the middle front of the chassis cover. 5. Slide the cover toward the rear of the chassis. Control Panel 6-2 Chapter 6: Advanced Chassis Setup 6-3 Remove These Screws Remove These Screws Remove This Screw Figure 6-3. Removing the Chassis Cover Warning: Except for short periods of time, do NOT operate the server without the cover in place. The chassis cover must be in place to allow proper airflow and prevent overheating. 6-4 System Fan A single 10-cm blower fan provides sufficient cooling for the SuperServer 5018A- MLTN4. The fan can adjust its speed according to the heat level sensed in the system, which results in more efficient and quieter fan operation. Fan speed is controlled by IPMI. SUPERSERVER 5018A-MLTN4 User's Manual Replacing the Blower Fan 1. Power down the system and disconnect the power cord from the from the rear of the power supply. 2. Place the chassis on a stable hard surface and remove the chassis cover as described in the previous section. 3. Remove the two long screws at the front of the blower and the two long screws at the back of the blower and set them aside for later use. 4. Lift the blower up and out of the chassis and disconnect the wiring. 5. Replace the blower with another blower of the same model and reconnect the wiring. 6. Align the thru holes in the blower with the thru holes in the chassis. 7. Secure the blower to the chassis using the screws previously set aside. 8. Close the cover and reconnect the power cord to the power supply. Long Screws Figure 6-4. Installing the Blower Fan 6-4 Chapter 6: Advanced Chassis Setup 6-5 Installing Hard Drives Remove these screws DVD-ROM/CD-ROM Drive Figure 6-5. Removing the CD-ROM Drive to Access the Hard Drive Installing a Hard Drive Before adding a hard drive, you must remove the DVD-ROM/CD-ROM drive as described in Section 6-6. 1. Power down the system and disconnect the power cord from the from the rear of the power supply. Place the chassis on a stable hard surface and remove the chassis cover as described in the Section 6-3. 2. If you have not already done so, remove the fan tray. For more information, see the Maintenance section located at the end of this chapter. 3. Remove the DVD-ROM/CD-ROM drive. To do this, remove the two screws holding the drive in place. One screw is external and the other is internal. 6-5 SUPERSERVER 5018A-MLTN4 User's Manual Hard Drive Figure 6-6. Adding the Hard Drive 4. Place the hard drive in the chassis as illustrated. Make sure the hard drive connectors face the inside of the chassis. 5. Secure the hard drive to the chassis using the four screws. 6. The chassis can support a second hard drive, which may be installed at this time. Hard Drive Second Hard Drive Figure 6-7. Adding a Second Hard Drive 6-6

FREE ENGLISH PDF

OPERATING INSTRUCTIONS

USER GUIDE - USER MANUAL

OWNER GUIDE - OWNER MANUAL

REFERENCE GUIDE - REFERENCE MANUAL

INSTRUCTION GUIDE - INSTRUCTION MANUAL