TOSHIBA 57HC85 (01) PDF MANUAL

Report any errors on this page in the comment box below.

PDF OCR Transcript: IntroductionConnecting your Monitor Using the remote control Projection Monitor OWNER’S MANUAL Setting up your Monitor Operating your Monitor AppendixIndex 51HC85 57HC85 65HC85 Owner's Record The model number and serial number are on the back of your monitor. Record these numbers in the spaces below. Refer to these numbers whenever you communicate with your Toshiba dealer about this monitor. Model: Serial No.: Owner's Record The model number and serial number are on the back of your monitor. Record these numbers in the spaces below. Refer to these numbers whenever you communicate with your Toshiba dealer about this monitor. Model: Serial No.: #01E_01_51HC85 05.4.28, 6:16 PM 1 Black (E) 51HC85, 57HC85, 65HC85 2500 Wilson Blvd. Arlington, VA 22201 U.S.A. Tel. 703-907-7600 Fax 703-907-7690 www.CE.org CEA is the Sponsor, Producer and Manager of the International CES® #01E_02-05_51HC85 05.4.28, 6:16 PM 2 Black NOTE: NEVER CONNECT THIS MONITOR TO A PERSONAL COMPUTER (PC). THIS MONITOR IS NOT INTENDED FOR USE WITH A PC. Dear Customer, Thank you for purchasing this Toshiba monitor. This manual will help you use the many exciting features of your new monitor. Before operating the monitor, please read this manual completely, and keep it nearby for future reference. Safety Precautions WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. NOTICE OF POSSIBLE ADVERSE EFFECTS ON MONITOR PICTURE DISPLAY If a fixed (non-moving) pattern or image remains on the monitor screen for extended periods of time, the image can become permanently ingrained in the cathode ray tube(s) of the monitor and cause subtle but permanent ghost images. This type of damage is NOT COVERED BY YOUR WARRANTY. See item 33 on page 4 for details. 2 NOTE: THIS MONITOR DOES NOT CONTAIN A TUNER. A set-top box (i.e., cable box or analog/digital receiver) is required to receive: (1) analog and/or digital broadcast signals from an antenna; and (2) analog and/or digital cable. For more information, refer to the applicable connection and setup instructions in this owner's manual. (E) 51HC85, 57HC85, 65HC85 WARNING RISK OF ELECTRIC SHOCK DO NOT OPEN The lightning symbol in the triangle tells you that the voltage inside this product may be strong enough to cause an electric shock. DO NOT TRY TO SERVICE THIS PRODUCT YOURSELF. The exclamation mark in the triangle tells you that important operating and maintenance instructions follow this symbol. ENERGY STAR® qualified monitor. Products that earn the ENERGY STAR prevent green house gas emissions by meeting strict energy efficiency guidelines set by the U.S. Environmental Protection Agency and the U.S. Department of Energy. ENERGY STAR and the ENERGY STAR mark are registered U.S. marks. Child Safety It Makes A Difference Where Your TV/monitor Stands Congratulations on your purchase! As you enjoy your new TV/monitor, keep these safety tips in mind: The Issue If you are like most consumers, you have a TV/monitor in your home. Many homes, in fact, have more than one TV/monitor. The home theater entertainment experience is a growing trend, and larger TVs/monitors are popular purchases; however, they are not always supported on the proper TV/monitor stands. Sometimes TVs/monitors are improperly secured or inappropriately situated on dressers, bookcases, shelves, desks, If you are like most consumers, you have a TV/monitor in your home. Many homes, in fact, have more than one TV/monitor. The home theater entertainment experience is a growing trend, and larger TVs/monitors are popular purchases; however, they are not always supported on the proper TV/monitor stands. Sometimes TVs/monitors are improperly secured or inappropriately situated on dressers, bookcases, shelves, desks, audio speakers, chests, or carts. As a result, TVs/monitors may fall over, causing unnecessary injury. Toshiba Cares! The consumer electronics industry is committed to making home The consumer electronics industry is committed to making home entertainment enjoyable and safe. The Consumer Electronics Association formed the Home Entertainment Support Safety Committee, comprised of TV/monitor and consumer electronics furniture manufacturers, to advocate children’s safety and educate consumers and their families about TV/monitor safety. Tune Into Safety One size does NOT fit all! Use appropriate furniture large enough to support the weight of your TV/ monitor (and other electronic components). Use appropriate angle braces, straps, and anchors to secure your furniture to the wall (but never screw anything directly into the TV/monitor). Carefully read and understand the other enclosed instructions for proper use of this product. Do not allow children to climb on or play with furniture and TVs/monitors. Avoid placing any item on top of your TV/monitor (such as a VCR, remote control, or toy) that a curious child may reach for. Remember that children can become excited while watching a program and can potentially push or pull a TV/monitor over. Share our safety message about this hidden hazard of the home with your family and friends. Thank you! #01E_02-05_51HC85 05.4.28, 6:16 PM 3 Black Important Safety Instructions 1) Read these instructions. 2) Keep these instructions. 3) Heed all warnings. 4) Follow all instructions. 5) Do not use this apparatus near water. 6) Clean only with a dry cloth. 7) Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. 8) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. 9) Do not defeat the safety purpose of the polarized or grounding type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet. 10) Protect the power cord from being walked on or pinched, particularly at plugs, convenience receptacles, and the point where it exits the apparatus. 11) Only use attachments/accessories specified by the manufacturer. 12) Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over. 13) Unplug this apparatus during lightning storms or when unused for long periods of time. 14) Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. 15) CAUTION: To reduce the risk of electric shock, do not use the polarized plug with an extension cord, receptacle, or other outlet unless the blades can be inserted completely to prevent blade exposure. (E) 51HC85, 57HC85, 65HC85 Wide plug QUALIFIED SERVICE TECHNICIAN Installation, Care, and Service Installation Follow these recommendations and precautions and heed all warnings when installing your monitor: 16) Never modify this equipment. Changes or modifications may void: a) the warranty, and b) the user’s authority to operate this equipment under the rules of the Federal Communications Commission. 17) DANGER: RISK OF SERIOUS PERSONAL INJURY, DEATH, OR EQUIPMENT DAMAGE! Never place the monitor on an unstable cart, stand, or table. The monitor may fall, causing serious personal injury, death, or serious damage to the monitor. 18) Never place or store the monitor in direct sunlight; hot, humid areas; areas subject to excessive dust or vibration; or locations with temperatures at or below 41°F (5°C). 19) Always place the monitor on the floor or a sturdy, level, stable surface that can support the weight of the unit. 20) Never place items such as vases, aquariums, or candles on top of the monitor. 21) Never block or cover the slots or openings in the monitor cabinet back, bottom, and sides. Never place the monitor: • on a bed, sofa, rug, or similar surface; • too close to drapes, curtains, or walls; or • in a confined space such as a bookcase, built-in cabinet, or any other place with poor ventilation. The slots and openings are provided to protect the monitor from overheating and to help maintain reliable operation of the monitor. 22) Never allow anything to rest on or roll over the power cord, and never place the monitor where the power cord is subject to wear or abuse. 23) Never overload wall outlets and extension cords. 3 30) [This item applies to projection monitors only.] If the air temperature rises suddenly (for example, when the 24) Always operate this equipment from monitor is first delivered), condensation may form on the a 120 VAC, 60 Hz power source only. lenses. This can make the picture appear distorted or the color appear faded. If this happens, turn off the monitor for 6 to 7 hours to allow the condensation to evaporate. 25) Always make sure the antenna system is properly 31) For added protection of your monitor from lightning and grounded to provide adequate protection against voltage power surges, always unplug the power cord if you leave surges and built-up static charges (see Section 810 of the the monitor unattended or unused for long periods of time. National Electric Code). Antenna lead-in wire 32) During normal use, the monitor may make occasional snapping or popping Antenna discharge unit (NEC Section 810-20) sounds. This is normal, especially when the unit is being turned on or off. If these sounds become frequent or continuous, unplug the power cord Electric service equipment Grounding conductors (NEC Section 810-21) and contact a Toshiba Authorized Service Center. 33) Possible Adverse Effects on Monitor Picture Display: If a Ground clamps Power service grounding electrode system (NEC Art 250 Part H) fixed (non-moving) pattern or image remains on the monitor screen for extended periods of time, the image can become permanently ingrained in the cathode ray tube(s) of the monitor 26) DANGER: RISK OF SERIOUS PERSONAL INJURY OR DEATH! • Use extreme care to make sure you are never in a position where your body (or any item you are in contact and cause subtle but permanent ghost images. This type of damage is NOT COVERED BY YOUR WARRANTY. Never leave the monitor on for extended periods of time while it is displaying the following images or formats: with, such as a ladder or screwdriver) can accidentally • Fixed Images, including but not limited to PIP/POP touch overhead power lines. Never locate the antenna windows, closed captions, video game patterns, TV station near overhead power lines or other electrical circuits. logos, stock tickers, and websites. • Never attempt to install any of the following during lightning activity: a) an antenna system; or b) cables, wires, or any home theater component connected to an antenna or phone system. • Special Formats that do not use the entire screen, including but not limited to widescreen or letterbox format media viewed on a 4:3 aspect ratio display (with gray or black bars at the top and bottom of the screen); or 4:3 aspect ratio format media viewed on a widescreen/16:9 aspect ratio display (with gray or black bars on the left and right sides of the screen). Care For better performance and safer operation of your TOSHIBA Service monitor, follow these recommendations and precautions: 34) WARNING: RISK OF ELECTRIC SHOCK! Never attempt to service the 27) Always sit approximately 10–25 feet away from the monitor and as directly in front of it as possible. The picture can appear dull if you sit too far to the left or right of the monitor, or if sunlight or room lights reflect on the screen. Turn the monitor off to check for reflections on the screen, and then monitor yourself. Opening and removing the covers may expose you to dangerous voltage or other hazards. Refer all servicing to a Toshiba Authorized Service Center. remove the source of reflections while viewing the monitor. 35) If you have the monitor serviced: • Ask the service technician to use only replacement parts specified by the manufacturer. 28) Always unplug the monitor before • Upon completion of service, ask cleaning. Never use liquid or the service technician to perform aerosol cleaners. routine safety checks to determine that the monitor is in safe operating condition. 29) WARNING: RISK OF ELECTRIC SHOCK! Never spill liquids or push objects of any kind into the monitor cabinet slots. 36) When the monitor reaches the end of its useful life, ask a qualified service technician to properly dispose of the monitor. Improper disposal may result in a picture tube implosion and possible personal injury. 4 #01E_02-05_51HC85 4 05.4.28, 6:16 PM Black (E) 51HC85, 57HC85, 65HC85 Ground clamp QUALIFIED SERVICE TECHNICIAN FCC compliance information Federal Communications Commission (FCC) This equipment complies with Part 15 of the FCC rules. NOTE: This equipment has been tested and found to comply with the limits for a Class B device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by removing and applying power to the equipment, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and the receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. Changes or modifications to this equipment not expressly approved by Toshiba could void the user’s authority to operate this equipment. #01E_02-05_51HC85 5 05.4.28, 6:16 PM Black Important Safety Precautions for Split Cabinet Feature (Models 57HC85 and 65HC85 only) Toshiba monitor models 57HC85 and 65HC85 have a split cabinet feature that allows disassembly of the cabinet into two sections during installation. For details, please refer to the insert titled “Disassembly/ Reassembly Instructions for Split Cabinet Feature” included with this owner’s manual in the accessory pack. If you do not have the insert, you can download a copy of it from our Web site (www.toshiba.com/tacp in the U.S.A. or www.toshiba.ca in Canada). If you do not have access to the Internet, call 1-800-631-3811 in the U.S.A. WARNING: If you split the cabinet for any purpose, NEVER energize the bottom section until it is completely and properly installed. Energizing the disassembled bottom section and subjecting it to intentional misuse (for example, exposing it to a foreign object) creates the potential for an electrical shock hazard that could result in death or serious injury. CAUTION: If you use the split cabinet feature, ALWAYS handle and treat the top section of the monitor cabinet, which contains a glass mirror, with great care. If subjected to excessive mechanical abuse (for example, if bumped or dropped), the mirror may break, creating exposed glass fragments with sharp edges. Contact with these glass fragments may result in injury. Installation, Care, and Service CAUTION: The split cabinet feature allows disassembly of the cabinet into two sections during installation. If you use the split cabinet feature, follow these precautions while the two sections of the monitor cabinet are disassembled: 1) Always handle and treat the top section of the monitor cabinet (with the viewing screen), which contains a glass mirror, with great care. If subjected to excessive mechanical abuse (for example, if bumped or dropped), the mirror may break, creating exposed glass fragments with sharp edges. Contact with these glass fragments may result in injury. 2) Never temporarily locate the disassembled bottom section in an area where it may be exposed to foreign objects or abuse (for example, areas where children may be playing, where items may fall on top of the unit, or where liquids may spill into the unit). Failure to follow this instruction may result in damage to the optic components of the monitor. SUCH DAMAGE IS NOT COVERED UNDER THE TOSHIBA LIMITED WARRANTY. 3) Always keep the top and bottom sections of the monitor cabinet in an upright position while disassembled. Failure to follow this instruction may result in damage to the monitor, including but not limited to the optic components, cabinet, bezel, and glass mirror. SUCH DAMAGE IS NOT COVERED UNDER THE TOSHIBA LIMITED WARRANTY. 4) Never energize the bottom section of the monitor cabinet while disassembled. Failure to follow this instruction could result in death or serious injury. 5) Never place anything on top of the disassembled bottom section of the monitor cabinet. Failure to follow this instruction may result in damage to the optic components. SUCH DAMAGE IS NOT COVERED UNDER THE TOSHIBA LIMITED WARRANTY. 6) Never store or transport the unit while it is disassembled. Failure to follow this instruction may result in damage to the monitor, including but not limited to the optic components, cabinet, bezel, and glass mirror. SUCH DAMAGE IS NOT COVERED UNDER THE TOSHIBA LIMITED WARRANTY. (E) 51HC85, 57HC85, 65HC85 5 Important Safety Information ............................. 2-5 Introduction................................................................ 7 Welcome to Toshiba ......................................................... 7 Exploring your new monitor ............................................ 7 Connecting your Monitor ........................................ 8 Connecting a VCR .......................................................... 9 Connecting a cable converter box and VCR ................... 10 Connecting a DVD player or satellite receiver and a VCR ............................................................................ 11 Connecting a DVD player with ColorStream® (component video) and a VCR ...................................... 12 Connecting a DTV receiver/set-top box with ColorStream® (component video) and a VCR ................ 13 Connecting two VCRs ................................................... 14 Connecting a camcorder ................................................ 14 Connecting an HDMITM or a DVI device to the HDMI input ........................................................... 15 Controlling infrared remote-controlled devices through the monitor (IR pass-through) .......................... 16 Connecting an audio system .......................................... 17 Using the remote control ...................................... 18 Preparing the remote control for use .............................. 18 Installing the remote control batteries ............................ 18 Remote control effective range ....................................... 18 Learning about the remote control ................................. 19 Using the remote control to operate your other devices .. 20 Remote control function key chart .......................... 21 Programming the remote control to operate your other devices ........................................................................... 22 Remote control codes .................................................... 22 Setting up your Monitor ........................................ 24 Turning on the Monitor ................................................. 24 Learning about the menu system ................................... 24 Changing the on-screen display language ....................... 25 Adjusting the color convergence..................................... 25 Operating your Monitor ......................................... 27 Viewing the wide-screen picture formats (480i, 480p, and 1080i signals only) ........................... 27 Selecting the picture size ......................................... 27 Scrolling the TheaterWide® picture (TheaterWide 2 and 3 only) ................................... 29 Using the AUTO ASPECT feature ......................... 30 Using the POP double-window feature .......................... 31 Swapping the main and POP pictures ..................... 32 Switching the speaker sound (main or POP program) .......................................... 32 Double-Window aspect ratio .................................. 32 Using the LOCKS menu ............................................... 33 Entering the PIN code ............................................ 33 If you cannot remember your PIN code .................. 33 Using the V-CHIP menu ............................................... 33 ENABLE BLOCKING .......................................... 34 TV RATING (Independent rating system for broadcasters) ........................................................... 34 MPAA RATING (Independent rating system for movies) ................................................................... 35 BLOCKING OPTION .......................................... 35 Changing the PIN code ................................................. 36 Adjusting the picture ..................................................... 36 Selecting the picture mode ...................................... 36 Adjusting the picture quality ................................... 37 Saving your new preferences ................................... 37 Selecting the color temperature ............................... 38 Using the CableClear® DNR feature ....................... 38 Resetting your picture setting adjustments .............. 39 Selecting the display format (for 480p signals only) ............................................ 39 Selecting the cinema mode ...................................... 39 Selecting the video input source ..................................... 40 Labeling the video input sources .................................... 40 Using the closed caption feature ..................................... 41 Setting the sleep timer .................................................... 42 Setting the clock ............................................................ 42 Adjusting the sound ....................................................... 43 Muting the sound ................................................... 43 Using the WOW® surround sound feature .............. 43 Adjusting the sound quality .................................... 44 Resetting your audio adjustments ........................... 44 Using the StableSound® feature .............................. 45 Turning off the built-in speakers ............................. 45 Selecting the Audio OUT sound ............................. 46 Selecting the background of the menu display ............... 46 Displaying monitor status information on-screen ........... 47 Understanding the last mode memory feature ................ 47 Appendix ................................................................... 48 Specifications ................................................................. 48 Troubleshooting ............................................................. 49 Limited United States Warranty ..................................... 50 Index .......................................................................... 51 6 #01E_06_51HC85 6 05.4.28, 6:16 PM Black (E) 51HC85, 57HC85, 65HC85 Introduction NOTE: THIS MONITOR DOES Welcome to Toshiba NOT CONTAIN A TUNER. A set-top box (i.e., cable box or Thank you for purchasing this Toshiba Monitor, one of the innovative projection monitors on the market. The goal of this manual is to guide you through setting up and operating your Toshiba monitor as quickly as possible. This manual applies to models 51HC85, 57HC85, and 65HC85. Before you start reading, check the model and serial numbers on the back of your monitor. Write these numbers in the space provided on analog/digital receiver) is required to receive: (1) analog and/or digital broadcast signals from an antenna; and (2) analog and/or digital cable. For more information, refer to the applicable connection and setup instructions in this owner’s manual. the front cover of this manual for your records. Instructions in this manual are based on using the remote control. You also can use the controls on the monitor’s front panel if they have the same name as those on the remote control. Please read all the safety and operating instructions carefully, and keep the manual for future reference. THIS MONITOR REQUIRES COLOR CONVERGENCE ADJUSTMENT AFTER SETTING UP. Convergence may drift as a result of relocating or adjusting the position of Exploring your new monitor the MONITOR. After setting up your MONITOR, it is recommended that You can operate your monitor using the buttons on the front panel or the remote control. The back panel and front panel (behind the door) provide all the terminal connections you will need to connect other you set the convergence. For instructions on adjusting the color convergence, see page 25. equipment to your monitor. See “Connecting your Monitor” on page 8. Illustrations represent 57HC85. 1 2 3 4 5 6 7 8 9100 0 ENT #01E_07_51HC85 7 05.4.28, 6:16 PM Black Remote control Front Remote sensor (behind the screen) POWERVideo 3 Power indicator Video/audio inputs (behind the door) IR OUT INPUTRECALL POWER Volume x • INFO+10 PIC SIZE EXIT STOP Variable Audio OUT VIDEO 3 IN OUT 1IR VOLUME MENU EXIT INPUT S-VIDEO VIDEO L/MONO R AUDIO MENU EXIT TOP MENU INPUTENTER CLEAR CT-90232 HDMI IN MENU DVDMENU ENTER TVCBL/SAT VCR DVD CH VOL MUTE SLEEP Back TV/VCR PAUSE PLAY FREEZE SOURCE SPLIT OUT 2 REW FF SKIP / SEARCH SWAP REC LIGHT VIDEO 1/2 ColorStream HD1/HD2 Audio OUT noitcudortnIr g otniitncoeMnr nuooCyl orte nhtocg e nitsoUmerr op tiung oniMttr euSoyr uor yog tinintoarMepOxidneppAx ednI7 (E) 51HC85, 57HC85, 65HC85 Connecting your Monitor Note: Cables except for Dual-wand IR blaster cable are not supplied with your monitor. ● Standard A/V (audio/video) cables usually come in sets of three, and are typically color-coded according to use: yellow for video, red for stereo right audio, and white for stereo left (or mono) audio. On your monitors back panel, the standard A/V inputs are color-coded in the same manner as the cables. ● S-video cable is for use with video equipment that has an S-video input. ● Component video cables come in sets of three, and are for use with video equipment that has component video inputs. (ColorStream® is Toshiba’s brand of component video.) ● HDMI cable is for use with video equipment that has an HDMI type A connector (see page 15). ● Dual-wand IR blaster cable is for use with video devices with IR (infrared) remote control. This can be used with the monitor’s IR pass- through feature (see page 16). Note: The IR blaster cable included with your monitor has specific characteristics that allows them to work properly with this monitor’s IR OUT ports. Never use other aftermarket IR blaster cable with this monitor. Other cables may not function properly and can cause damage. THIS TYPE OF DAMAGE IS NOT COVERED BY YOUR TOSHIBA WARRANTY. NOTE REGARDING PICTURE QUALITY When connecting video equipment to your Toshiba monitor: ● For GOOD picture quality: Use a standard yellow video cable. ● For BETTER picture quality: If your equipment has an S-video input, use an S-video cable instead of a standard yellow video cable. (You still must connect the standard red and white audio cables for full system connection, but do not connect the standard yellow video cable at the same time, or the picture performance will be unacceptable.) ● For BEST picture quality: If your equipment has component video (or HDMI) inputs, use either component video cables (or an HDMI cable) instead of a standard video or S-video cable. (A component video connection requires separate audio cables. An HDMI connection does not require separate audio cables.) noitcudortnIr g otniitnStandard A/V cables (red/white/yellow) coeMnr nuoS-video cable oCyl oComponent video cables rte nhotCg e ntiHDMI cable soUmeRDual-wand IR blaster cable p NOTICE: uV Tg RISK OF EQUIPMENT DAMAGE! r niuDo not plug in any power cords ttoeuntil you have finished connecting all equipment. ySs ’Vs Tere uhttag enFisUxidneppAx ednI8 #01E_08-17_51HC85 8 05.4.28, 6:16 PM Black (E) 51HC85, 57HC85, 65HC85 Connecting a VCR This connection allows you to watch video tapes. You will need: • one set of standard A/V cables IN from ANT OUT to TV CH 3 CH 4 VIDEO AUDIO Note: If you have a mono VCR, connect L/Mono to VCR Audio OUT using only one audio cable. If you have a VCR with S-video, use an From Cable Box or AntennaS-video cable (in the S-video terminals) instead of the standard video cable. Stereo VCR Do not connect a standard video cable and an S-video cable to Video-1 (or Video-2) at the same time, or the picture performance will be unacceptable. The unauthorized recording, use, Monitor distribution, or revision of television programs, videotapes, DVDs, and other materials is prohibited under Copyright Law of the United States and other countries, and may subject you to civil and criminal liability. #01E_08-17_51HC85 9 05.4.28, 6:16 PM Black INOUT OUT 1IR L R OUT 2 noitcudortnIr g otniitncoeMnr nuooCyl orte nhtocg e nitsoUmerr op tiung oniMttr euSoyr uor yog tinintoarMepOxidneppAx ednI9 (E) 51HC85, 57HC85, 65HC85 Connecting a cable converter box and VCR This connection allows you to watch basic and premium cable channels and watch video tapes. To watch basic and premium cable channels, put the monitor in VIDEO 1 mode and set the VCR to channel 3 or 4 (whichever channel is vacant in your area), and use the converter box to change channels. You will need: • two coaxial cables • one set of standard A/V cables IN from ANT OUT to TV CH 3 CH 4 VIDEO AUDIO Note: If you have a mono VCR, connect L/Mono to VCR Audio OUT using only one audio cable. If you have a VCR with S-video, use an S- video cable (in the S-video terminals) instead of a standard video cable. Do not connect a standard video cable and an S-video cable to Video-1 (or Video-2) at the same time, or the picture performance will be unacceptable. Monitor The unauthorized recording, use, distribution, or revision of television programs, videotapes, DVDs, and other materials is prohibited under Copyright Law of the United States and other countries, and may subject you to civil OUT 1and criminal liability. OUT 2 IR Stereo VCR From cable OUT IN Cable converter box #01E_08-17_51HC85 10 05.4.28, 6:16 PM Black noitcudortnIr g otniitncoeMnr nuooCyl orte nhotCg e ntisoUmeRp uV TINg r niutOUT toeyL R Ss ’Vs Tere uhttag enFisUxidneppAx ednI10 (E) 51HC85, 57HC85, 65HC85 Connecting a DVD player or satellite receiver and a VCR This connection allows you to watch DVD/satellite and VCR. You will need: • one (or two, if satellite receiver is used) coaxial cable • one set of standard A/V cables (between the monitor and VCR) • one S-video cable (between the monitor and DVD player/satellite receiver) • one pair of standard audio cables (between the monitor and DVD player/satellite receiver) IN from ANT OUT to TV CH 3 CH 4 VIDEO AUDIO Note: For the highest possible picture quality from a DVD player or satellite receiver without component video or HDMI, use an S-video cable. (If your DVD player has component video, see page 12. If your DVD player or satellite receiver has HDMI or DVI, see page 15.) Do not connect both an S-video cable and a standard video cable between the monitor and DVD player/satellite receiver at the same time or the picture performance will be unacceptable. Do not connect the DVD player/satellite receiver and VCR to the same set of Video inputs on the monitor. (See the illustrations, which show the DVD player/satellite receiver connected to Video-1 on the monitor, and the VCR connected to Video-2 on the monitor.) The unauthorized recording, use, distribution, or revision of television programs, videotapes, DVDs, and other materials is prohibited under Copyright Law of the United States and other countries, and may subject you to civil and criminal liability. Stereo VCR INOUT From L R Antenna From S-VIDEO VIDEO OUT OUT Satellite Dish Monitor DVD player Satellite receiver #01E_08-17_51HC85 11 05.4.28, 6:16 PM Black OUT 1OUT 2 IR AUDIO OUT LR IN from ANT S-VIDEO VIDEO OUT OUT AUDIO LOUT R noitcudortnIr g otniitncoeMnr nuooCyl orte nhtocg e nitsoUmerr op tiung oniMttr euSoyr uor yog tinintoarMepOxidneppAx ednI11 (E) 51HC85, 57HC85, 65HC85 Connecting a DVD player with ColorStream® (component video) and a VCR This connection allows you to watch DVDs and video tapes. Your monitor has ColorStream (component video) inputs. Connecting your monitor to a DVD player with component video output (such as a Toshiba DVD player with ColorStream) can greatly enhance picture quality and realism. You will need: • one coaxial cable • one set of standard A/V cables • one pair of audio cables • one set of component video cables (one S-video cable for a DVD player without component video inputs; see notes at right) IN from ANT OUT to TV CH 3 CH 4 VIDEO AUDIO Note: For the highest possible picture quality, use component video cables (or an HDMI cable) between the monitor and DVD player. You can connect component video cables to either set of ColorStream terminals on the monitor (HD1 or HD2). For HDMI or DVI connection, see page 15. The ColorStream HD1/HD2 and HDMI terminals can be used with Progressive (480p, 720p) and Interlaced (480i,1080i) scan systems; however, a 1080i signal will provide the best picture performance. From Antenna If your DVD player is not compatible with component video, HDMI, or DVI, use the Stereo VCR S-video connections (plus the standard audio connections) instead (see page 11). The unauthorized recording, use, Monitor distribution, or revision of television programs, videotapes, DVDs, and other materials is prohibited under Copyright Law of the United States and other countries, and may subject you to civil and criminal liability. #01E_08-17_51HC85 12 05.4.28, 6:16 PM Black INOUT L R OUT 1OUT 2 IR S-VIDEO VIDEO OUT DVD player with component video AUDIO COMPONENT VIDEO noitcudortnIr g otniitncoeMnr nuooCyl orte nhotCg e ntisoUmeRp uV Tg r niuttoeySs ’Vs Tere uhttag enFOUT iLLsY PB PR UR R xidneppAx ednI12 (E) 51HC85, 57HC85, 65HC85 Connecting a DTV receiver/set-top box with ColorStream® (component video) and a VCR This connection allows you to watch DTV (digital TV), VCR, and TV programs, and record DTV (composite video only) and TV programs. Your monitor has ColorStream (component video) inputs. Connecting your monitor to a DTV receiver with component video inputs can greatly enhance picture quality and realism. – To watch a DTV program, select ColorStream HD2 on the monitor. – To record and watch the same TV program, tune the VCR to the channel to record, and select VIDEO 1 on the monitor. – To record one program while watching another, tune the VCR to the channel to record, tune the DTV receiver to the channel to watch, and select ColorStream HD2 on the monitor. You will need: • two coaxial cables • two sets of standard A/V cables • one pair of audio cables • one set of component video cables (one S-video cable for a DTV receiver without component video; see notes at right) IN from ANT OUT to TV CH 3 CH 4 VIDEO AUDIO Note: For the highest possible picture quality, use component video cables (or an HDMI cable) between the monitor and DTV receiver/set- top box. You can connect component video cables to either set of ColorStream terminals on the monitor (HD1 or HD2). For HDMI or DVI connection, see page 15. The ColorStream HD1/HD2 and HDMI terminals can be used with Progressive (480p, 720p) and Interlaced (480i, 1080i) scan systems; however, a 1080i signal will provide the best picture performance. If your DTV receiver or set-top box is not compatible with component video, HDMI, or DVI, use the S-video connections (plus the standard audio connections) instead (see page 11). The unauthorized recording, use, distribution, or revision of television From Antenna programs, videotapes, DVDs, and other materials is prohibited under Copyright Law of the United States and other Stereo VCR countries, and may subject you to civil and criminal liability. From DTV Antenna DTV Receiver with component video #01E_08-17_51HC85 13 05.4.28, 6:16 PM Black INOUTL R Monitor OUT 1OUT 2 IR S-VIDEO VIDEO OUT AUDIO COMPONENT VIDEO OUT Y PB PR LLSatellite IN R R noitcudortnIr g otniitncoeMnr nuooCyl orte nhtocg e nitsoUmerr op tiung oniMttr euSoyr uor yog tinintoarMepOxidneppAx ednI13 (E) 51HC85, 57HC85, 65HC85 Connecting two VCRs This connection allows you to record (dub/edit) from one VCR to another VCR while watching a videotape. – To record one program while watching another, tune VCR1 to the channel to record, tune VCR2 to the channel to watch, and select VIDEO 2 on the monitor. You will need: • one signal splitter • three coaxial cables • three sets of standard A/V cables IN from ANT OUT to TV CH 3 CH 4 VIDEO AUDIO Note: If you have VCR (VCR1) with S-video, use S-video cables instead of standard video cables for better picture performance. Do not connect both a standard video cable and an S-video cable to Video-1 (or Video-2) at the same time or the picture performance will be unacceptable. Do not connect the same VCR to the output and input terminals is on the monitor at the From Antennasame time. To dub or edit, VCR 2 must select Line IN, and the monitor must select VIDEO 1.IN Splitter VCR1 OUT OUT The Video OUT terminal does not output the POP picture. ** The Audio OUT terminals can output the sound of either the Main or POP picture (see “Selecting the Audio OUT sound” on page 46). Monitor VCR2 Connecting a camcorder This connection allows you to watch video materials recorded on a camcorder. Note: You will need: • one set of standard A/V cables If you have a camcorder with S-video, use an S-video cable instead of a standard video cable for better picture performance. Do not connect both a standard video cable and an S-video cable at the same time or the picture performance will be unacceptable. VIDEO AUDIO OUT LR S-VIDEO VIDEO AUDIO INOUT IN from ANT OUT to TV L R The unauthorized recording, use, distribution, or revision of television programs, videotapes, DVDs, and other materials is prohibited under Copyright Law of the United States and other countries, and may subject you to civil and criminal liability. Camcorder Video-3 (front panel) #01E_08-17_51HC85 14 05.4.28, 6:16 PM Black OUT 1OUT 2 IR * VIDEO AUDIO CH 3 L R CH 4 noitcudortnIr g otniitncoeMnr nuooCyl orte nhotCg e ntisoUmeRp uV Tg r niuttoeySINs ’OUT Vs Tere uhttag enFisUxidneppAx ednIVIDEO 3 IN 14 L/MONO R (E) 51HC85, 57HC85, 65HC85 Connecting an HDMITM or a DVI device to the HDMI input The HDMI[1] input on your monitor receives digital [1] HDMI = High-Definition Multimedia Interface. audio and uncompressed digital video from an HDMI [2] DVI = Digital Video Interface. device or uncompressed digital video from a DVI[2] [3] HDCP = High-bandwidth Digital Content Protection. device. [4] EIA/CEA-861/861B compliance covers the transmission of This input is designed to accept HDCP[3] program material in digital form from EIA/CEA-861/861B– compliant[4] consumer electronic devices (such as a set- top box or DVD player with HDMI or DVI output). Monitor uncompressed digital video with high-bandwidth digital content protection, which is being standardized for reception of high-definition video signals. Because this is an evolving technology, it is possible that some devices may not operate properly with the monitor. The HDMI input is designed for best performance with 1080i high-definition video signals, but will also accept and display 480i, 480p, and 720p signals. VIDEO L AUDIO R INOUT To ensure that the HDMI or DVI device is reset properly, it is recommended that you follow these procedures: NOTE: NEVER CONNECT THIS MONITOR TO A PERSONAL COMPUTER (PC). THIS MONITOR IS NOT INTENDED FOR USE WITH A PC. • When turning on your electronic components, turn on the monitor first, and then the HDMI or DVI device. • When turning off your electronic components, turn off the HDMI or DVI device first, and then the monitor. To connect an HDMI device, you will need: • one HDMI cable (type A connector) For proper operation, it is recommended that you use a short HDMI cable. You should not encounter To connect a DVI device, you will need: • one HDMI-to-DVI adapter cable (HDMI type A connector) difficulty if you use an HDMI cable shorter than For proper operation, the length of the HDMI-to-DVI 16.4 ft (5m). adapter cable should not exceed 9.8 ft (3m). The HDMI cable transfers both video and audio. Separate analog audio cables are not required (see recommended length is 6.6 ft (2m). • one pair of standard analog audio cables illustration below). Some CDVs (video CDs) may not output digital audio signals. In that case, you may hear sound by connecting analog audio cables. However, if you connect analog audio cables with An HDMI-to-DVI adapter cable transfers video only. Separate analog audio cables are required (see illustration below). this connection, the HDMI terminal on the monitor will not receive the HDMI digital audio signal and DVI device you will hear analog audio only. Monitor OUT 1IR #01E_08-17_51HC85 15 05.4.28, 6:16 PM Black VIDEO L AUDIO R DVI OUT INOUT HDMI device HDMI OUT OUT 1IR HDMI, the HDMI logo, and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing, LLC. OUT 2 OUT 2 noitcudortnIr g otniitncoeMnr nuooCyl orte nhtocg e nitsoUmerr op tiung oniMttr euSoyr uor yog tinintoarMepOxidneppAx ednI15 (E) 51HC85, 57HC85, 65HC85 Controlling infrared remote-controlled devices through the monitor (IR pass-through) You can use the monitor’s IR OUT terminal (infrared pass-through) to remotely operate (through the monitor) many infrared remote- controlled devices (such as a Toshiba infrared remote-controlled VCR or DVD player) enclosed within an entertainment center or similar cabinet. Without the IR OUT connection, the device typically would need to be visible to operate it remotely. You will need: • one dual-wand IR blaster cable (included with your monitor) • other audio/video cables as required to connect the device(s) to the monitor (see pages 8-15). To connect the IR blaster cable: 1. Locate the infrared sensor on the front of your device. This sensor is marked on some devices. 2. Align one of the IR blaster cable’s wands about 1 inch away from the infrared sensor on the front of the device and attach it using the enclosed mounting tape. If you have a second device, attach the second wand in a similar manner (see illustration below). Note: If you do not have a second device, coil the second wand with a rubber band and leave it behind the monitor. 3. Plug the IR blaster cable’s plug into the monitor’s IR OUT terminal. OUT 1IR To control the device(s): Point the monitor remote control (programmed to operate the device; see pages 22–23) or the device’s remote control at the front of the monitor and press the button for the desired function. The signal passes from the remote control through the monitor to the device via the IR blaster cable. Front of IR-controlled DVD player (for example) Front of IR-controlled audio device (for example) Infrared sensor IR blaster cable wand (approx. 1 inch from device) INPUT RECALL +10 PIC SIZE EXIT POWER INFO TV/VCR PAUSE STOPMUTE SLEEP FF 1 2 3 4 5 6 7 8 9 TOPMENU 100 0 ENT MENU DVDMENUENTER ENTER VCRDVD TVCBL/SAT CH CLEAR VOL REW FREEZE SOURCE PLAY REC SWAP noitcudortnIr g otniitncoeMnr nuooCyl orte nhotCg e ntisoUmeRp uV Tg SKIP / SEARCHSPLIT r nLIGHT iuttoeyIf you use the device’s remote control Sto operate the device, you also will Back of TV need to use the monitor’s remote control to operate the monitor. s ’Vs TIf you cannot locate the device’s infrared ere sensor: uhtt1. Turn OFF the device. ag enFOUT 2 i2. Starting at the lower left corner of the sdevice, place the end of the device’s Uremote control (with the infrared emitter) so it touches the front of the device and press POWER. (Do not use the monitor’s remote control for this step.) xi3. If the device turns on, the place that the dremote control touched the device is the nelocation of the sensor. pp4. If the device does not turn on, move the Aremote control slightly to the right and press POWER again. 5. Repeat step 4 until you locate the device’s infrared sensor. x ednI16 #01E_08-17_51HC85 16 05.4.28, 6:16 PM Black (E) 51HC85, 57HC85, 65HC85 Connecting an audio system This connection allows you to use an audio amplifier and external speakers and adjust the audio level using the monitor’s remote control. To control the audio, turn on the monitor and the stereo amplifier, and turn off the built-in speakers (see “Turning off the built-in speakers” on page 45). You will need: • one pair of standard audio cables LINE L IN R OUT 1IR Note: To hear sound when using an external audio amplifier, the volume of both the monitor and the amplifier must be set above 0 (zero). For example, if the volume of the monitor is set to 0, you will not be able to hear any sound even if the volume of the amplifier is at its highest level. Monitor Amplifier OUT 2 #01E_08-17_51HC85 17 05.4.28, 6:16 PM Black noitcudortnIr g otniitncoeMnr nuooCyl orte nhtocg e nitsoUmerr op tiung oniMttr euSoyr uor yog tinintoarMepOxidneppAx ednI17 (E) 51HC85, 57HC85, 65HC85 Using the remote control Preparing the remote control for use Your monitor remote control can operate your monitor and most cable converter boxes, satellite receivers, VCRs, DVD players, and HTIBs (home theater in a box), even if they are different brands. If you have a Toshiba device: Your monitor remote control is preprogrammed to operate most Toshiba devices. See pages 20–21. If you have a non-Toshiba device or a Toshiba device that the remote control is not preprogrammed to operate: You can program the monitor remote control so it will operate the other device. See pages 20–23. Installing the remote control batteries 1. Remove the battery cover from the back of the remote control. 2. Install two “AA” size batteries, making sure to match the + and – signs on the batteries to the signs on the battery compartment. 3. Reinsert the battery cover in the remote control until the tab snaps. Remote control effective range For optimum performance, aim the remote control directly at the monitor and make sure there is no obstruction between the remote control and the monitor. Note: Your monitor’s remote control may not operate certain features on your VCR or other electronic device. Refer to the owner’s manuals for your other devices to determine their available features. If your monitor’s remote control does not operate a specific feature on a device, use the remote control that came with the device. #01E_18-23_51HC85 18 05.4.28, 6:16 PM Black noitcudortnIg niV tTcr eunonyoCl orte nhtocg Caution: e nit• Never throw batteries into a fire. soUmeNote: r• Be sure to use AA size batteries. • Dispose of batteries in a designated Squeeze tab and disposal area. lift cover. • Batteries should always be disposed of with p uV the environment in mind. Always dispose of Tg batteries in accordance with applicable laws r niutand regulations. toey• If the remote control does not operate Scorrectly, or if the operating range becomes reduced, replace batteries with new ones. • When necessary to replace batteries in the remote control, always replace both s ’batteries with new ones. Never mix battery Vs Ttypes or use new and used batteries in ere combination. uhtta• Always remove the batteries from the g enFremote control if they are dead or if the isremote control is not to be used for an Uextended period of time. This will prevent battery acid from leaking into the battery compartment. xidneppAx ednI18 (E) 51HC85, 57HC85, 65HC85 Learning about the remote control The buttons used for operating the monitor only are described here. POWER turns the monitor on and off RECALL displays monitor status information on-screen (page 47) SLEEP sets the monitor to turn off at a specific time (page 42) INPUT selects the video input source (page 40) MUTE reduces or turns off the sound (page 43) Device Switch switches among TV, CBL/SAT, VCR, and DVD modes (pages 20-23) Set to “TV” to control the monitor. Numbers (0-9, 100) enters the numbers directly VOL (volume) y z adjusts the volume level MENU accesses the on-screen system (page 24) ENTER activates the function settings in the menu (page 24) y z x • (arrows) select or adjust items in the menus (page 24) PIC SIZE cycles through the five picture sizes: Natural, TheaterWide 1, 2, 3, and Full (page 27) EXIT closes on-screen menus (page 24) SPLIT turns the POP feature on and off (page 31) SOURCE selects the POP picture source (page 31) FREEZE freezes the picture. Press again to restore the moving picture. SWAP switches the main and POP pictures (page 32) LIGHT illuminates the keypad for five seconds INPUTRECALL POWER INFO1 2 3 4 5 6 7 8 9+10 100 0 ENT TOP MENU PIC SIZE ENTER EXICT LEAR STOP CT-90232 #01E_18-23_51HC85 19 05.4.28, 6:16 PM Black MENU DVDMENU ENTER TVCBL/SAT VCR DVD CH VOL MUTE SLEEP TV/VCR PAUSE PLAY FREEZE SOURCE SPLIT REW FF SKIP / SEARCH SWAP REC LIGHT Note: The error message “Not Available” will appear if you press a key for a function that is not available. noitcudortnIr g otniitncoeMnr nuooCyl orte nhtocg e nitsoUmerr op tiung oniMttr euSoyr uor yog tinintoarMepOxidneppAx ednI19 (E) 51HC85, 57HC85, 65HC85 Using the remote control to operate your other devices If you have a non-Toshiba device or a Toshiba device that the remote control is not preprogrammed to operate, you must first program the remote control to recognize the device (if you have not already done so). See pages 22 and 23. To use your monitor remote control to operate a: • Cable converter box or satellite receiver, set the Device Switch to “CBL/SAT”. • VCR, set the Device Switch to “VCR”. • DVD player or HTIB, set the Device Switch to “DVD”. Note: Even after the monitor remote control is programmed, it may not operate certain features on your other device. If this happens and you wish to use those features, you will need to use the device’s original remote control. Point the remote control directly at the device. 1 2 3 4 5 6 7 8 9+10 Press to directly access 100 0 ENT DVD chapters higher than 10. TOP MENU Accesses a DVD’s top menu. ENTER Required by cable converter boxes to change the channel. Device Switch Set to “TV” to control the monitor; “CBL/ SAT” to control a cable converter box or satellite receiver; “VCR” to control a VCR; “DVD” to control a DVD player or HTIB. TV/VCR REW Rewinds the tape or DVD. (Press during play mode to view the picture moving rapidly backward.) REC Starts tape recording. #01E_18-23_51HC85 20 05.4.28, 6:16 PM Black INPUTRECALL POWER +10 PIC SIZE EXIT POWER INFOTurns the selected device on and off. STOP RECALL/INFO Displays on-screen information. Channel Numbers (0-9) Press to directly access channels (as opposed to CH y z). DVD MENU TOP MENU Accesses DVD menus. ENTER CLEAR CT-90232 FF Fast-forwards the tape or DVD. (Press during play mode to view the picture moving rapidly forward.) MENU y z x • DVDMENU Press to navigate DVD menus (may not work on some DVD players). ENTER CLEAR Press to reset the DVD title and chapter number. TVCBL/SAT VCR DVD CH VOL CH y z y selects the next higher channel; MUTE SLEEP z selects the next lower channel. PAUSE Press during play or record mode to pause the picture; press again to restart. TV/VCR PAUSE PLAY REW FF SKIP / SEARCH PLAY FREEZE SOURCE SPLIT Begins playback of a tape or DVD. SWAP REC LIGHT noitcudortnIg niV tTcr eunonyoCl orte nhtocg e nitsoUmerp uV Tg r niuttoeySs ’Vs Tere uhttag enFisUxidneppSTOP AStops the tape or DVD. SKIP/SEARCH Skips forward to locate later DVD chapters. SKIP/SEARCH x eSkips back to beginning of current DVD dchapter or locates previous chapters. nI20 (E) 51HC85, 57HC85, 65HC85 Remote control function key chart Key Label Monitor Cable/Satellite VCR DVD POWER Power Power Power Power INPUT Input ← ← ← RECALL/INFO On-screen display INFO --- On-screen display 1 Digit 1 Digit 1 Digit 1 Digit 1 2 Digit 2 Digit 2 Digit 2 Digit 2 3 Digit 3 Digit 3 Digit 3 Digit 3 4 Digit 4 Digit 4 Digit 4 Digit 4 5 Digit 5 Digit 5 Digit 5 Digit 5 6 Digit 6 Digit 6 Digit 6 Digit 6 7 Digit 7 Digit 7 Digit 7 Digit 7 8 Digit 8 Digit 8 Digit 8 Digit 8 9 Digit 9 Digit 9 Digit 9 Digit 9 0 Digit 0 Digit 0 Digit 0 Digit 0 100/-/+10 100 100/- 100 +10 ENT --- --- --- --- TOP MENU --- --- --- Top Menu GUIDE/ PIC SIZE Selects the image shape. Guide --- --- ENTER/ENTER Enter Select --- Enter CLEAR/EXIT Exit Exit --- Clear x •/yz Menu select Menu select --- Menu select VOLyz Volume up/down ← ← ← CHyz --- Channel up/down Channel up/down --- SLEEP Sleep timer --- --- --- MUTE Sound mute ← ← ← PLAY/SPLIT POP Split --- Play Play STOP/SOURCE POP Source --- Stop Stop PAUSE/FREEZE Still picture --- Pause Pause TV/VCR --- --- TV/VCR --- SKIP/SEARCH up/down --- Search– + Skip FWD/REV FF/SWAP POP Swap --- Fast FWD Fast FWD REW --- --- Rewind Rewind REC --- --- Record --- LIGHT Lights the remote key. Note: • “---” will send nothing. • “←” same as left column. #01E_18-23_51HC85 21 05.4.28, 6:16 PM Black noitcudortnIr g otniitncoeMnr nuooCyl orte nhtocg e nitsoUmerr op tiung oniMttr euSoyr uor yog tinintoarMepOxidneppAx ednI21 (E) 51HC85, 57HC85, 65HC85 Programming the remote control to operate your other devices Your Toshiba monitor remote control is preprogrammed to operate most Toshiba devices. To program your monitor remote control to operate a non-Toshiba device (or a Toshiba device that it is not preprogrammed to operate), follow the steps below. For details on using the remote control to operate the device, see pages 20–21. 1. In the remote control code table (below and on the next page), find the code for your device. If more than one code is listed, try each one separately until you find one that works. 2. Set the Device Switch to the type of device you are programming the remote control to operate — CBL/SAT (for a cable converter box or satellite receiver), VCR (for a VCR or TV/VCR combo), or DVD (for a DVD player or HTIB [home theater in a box]). 3. While holding down RECALL, press the Channel Number buttons to enter the 3-digit code for your device. 4. To test the code, turn on the device, point the remote control at it, and press POWER. See notes at right. • If the correct code was entered, the device will turn off. • If the device does not respond, repeat steps 1 – 4 using another code. • If the device does not respond to another code, you will need to use the remote control that came with the device. 5. Remember to set the Device Switch back to “TV” to control the monitor. 6. For future reference, write down the code(s) you used: Remote control codes In some cases you may not be able to operate your device with the monitor remote control. Your other device may use a code that is not recognized by the monitor remote control. If this happens, use the device’s remote control. RECALL Cable converter box ABC: 061, 062, 063, 082, 084, 087, 091, 092, 096, 098 Archer: 065, 092, 097, 099 Cableview: 064, 094 Century: 092 Citizen: 090, 092, 097 Contec: 083, 085, 086, 088, 093, 098 Diamond: 093 Eagle: 091 GE: 061, 062 Gemini: 069, 070, 094 General Instruments: 062, 089, 096 INPUTRECALL POWER INFOPOWER 1 2 3 4 5 6 Channel 7 8 9Number buttons +10 100 0 ENT TOPMENU PIC SIZE MENU DVDMENU ENTEENR TER EXICT LEAR TVCBL/SAT CH VOL Device Switch VCR DVD POP DIRECT CH MUTE SLEEP TV/VCR PAUSE STOP PLAY Note: REW FREEZE FF noitcudortnIg niV tTcr eunonyoCl orte nhtocg e nitsoUmerSOURCE SPLIT SKIP / SEARCH • In CH REC addition SCAN SWAP to POP POWER, CHLIGHT confirm that all necessary keys on the monitor remote control will operate your device. If some keys are not operational, repeat the device p uV code setup using another code (if other Tg codes are listed for your device). If, after r niutDEVICE CODE DEVICE CODE trying all listed codes, the necessary keys toeydo not operate your device, use the Sdevice’s original remote control. • Every time you change the batteries, you will need to reprogram the remote control. • Some newer VCRs respond to either of two s ’codes. These VCRs have a switch labeled Vs T“VCR1/VCR2.” If your VCR has this kind of ere switch and does not respond to the codes uhttfor your VCR brand, set the switch to the ag eother position (“VCR1” or “VCR2”) and nFisreprogram the remote control. UHamlin: 093 RCA: 064, 081 U. S. Electronics: 087, 010, 011, 012, 022, Hitachi: 062, 095, 096 Realistic: 065 096, 098 023, 031, 049 Jasco: 097 Recoton: 102 United Cable: 082 Hitachi: 033 xiJerrold: 062, 069, 071, Samsung: 077, 090 Universal: 065, 092, 097, Hughes: 033 dn082, 086, 089, 091, Scientific Atlanta: 063, 099, 102, 103 Hughes Network ep096 078, 079, 080, 088, Wards: 096 Systems: 019 pMagnavox: 072, 096 098, 101, 105 Intersat: 048 AMemorex: 091, 092, 104 Sears: 095 Satellite receiver Janeil: 027 Multi Canal: 090 Signature: 062 Alphastar: 038, 059 JVC: 017, 057 Novavision: 101 Signature 2000: 096 Chaparral: 034 Kenwood: 029 Panasonic: 081, 083, 085 Sprucer: 081, 085 DISH Network: 057 Magnavox: 060 Philco: 087 Starcom: 069, 082, 087, Drake: 020, 040, 044, Optimus: 058 Philips: 066, 067, 068, 096, 103, 104 046, 050, 053 Pansat: 036, 052 x 070, 072, 073, 074, Stargate: 069, 090 Echostar: 018, 041, 051 Primestar: 015, 042 ed075, 091, 092 Sylvania: 095, 100 Express Vu: 057 Proscan: 008, 009, 013 nIPioneer: 076, 077 TeleView: 090 Fujitsu: 027 Radio Shack: 022, 023, Proscan: 061, 062 Texscan: 100 GE: 008, 009, 013 030 Radio Shack: 092, 097, Tocom: 071, 084, 085 General Instruments: 099 22 #01E_18-23_51HC85 22 05.4.28, 6:16 PM Black (E) 51HC85, 57HC85, 65HC85 Remote control codes (cont.) Satellite receiver (cont.) RCA: 008, 009, 013, 016 Realistic: 030 Samsung: 059 Sony: 014, 055 Star Choice: 057 Star Trak: 025, 026, 037, 054 STS: 024 Toshiba: 000, 001, 002, 003, 004, 005, 006, 007, 020, 031, 056 Uniden: 021, 028, 030, 032, 035, 039, 043, 045, 047, 058 Zenith: 027 TV/VCR Combo Action: 078 GE: 059, 062 Goldstar: 065 Panasonic: 065 Precision: 078 Quasar: 065 Realistic: 079 Sony: 074 Toshiba: 057 Totevision: 009, 010, 065 Zenith: 065 DVD/VCR Combo Go Video: DVD=087, VCR=081 JVC:DVD=088, VCR=082 RCA:DVD=089, VCR=083 Samsung: DVD=090, VCR=084 Sanyo:DVD=091, VCR=085 Zenith:DVD=092, VCR=086 DVD player Aiwa: 006, 015 Apex: 016, 017 BOSE: 097 Broksonic: 018 Clarion: 019 Classic: 020 Daewoo: 021 Denon: 022, 023, 024, 025 Emerson: 026, 027 Fisher: 028 Funai: 027 GE: 001, 029, 030 Go Video: 087 GPX: 031 Hitachi: 005, 032, 033, 034, 035 JVC: 003, 007, 036, 042, 088 Kenwood: 037 Konka: 008, 009 Magnavox: 004, 038 Memorex: 039 Mintek: 040 NAD: 026 Nakamichi: 041 Norcent: 043 Onkyo: 044 Oritron: 058 Panasonic: 010, 045, 046, 047, 048, 049, 050 Philips: 004, 051 Pioneer: 052, 053, 054, 055 Proscan: 001, 056 Qwestar: 057, 058 RCA: 001, 002, 059, 089 Sampo: 060 Samsung: 061, 062, 086, 090 Sansui: 073 Sanyo: 063, 091 Sharp: 064, 067 Sherwood: 074 Sony: 011, 012, 065, 066, 068, 069, 070 Sylvania: 027 Teac: 071 Technics: 072 Techwood: 075 Toshiba: 000, 013, 076, 077, 078 Yamaha: 079, 080, 081 Zenith: 014, 082, 092 Portable DVD player Aiwa: 093 Audiovox: 094, 095 Panasonic: 024, 096, 099 RCA: 098 VCR Admiral: 049 Aiko: 019 Aiwa: 018 Akai: 003, 004, 037, 038, 039, 058, 069 Audiovox: 010 Bell & Howell: 007, 068 Broksonic: 008, 017 Calix: 010 Carver: 026 CCE: 019 Citizen: 009, 010, 011, 012, 013, 014, 015, 019, 057, 073 Colortyme: 005 Craig: 009, 010, 016, 061, 065, 079 Curtis Mathes: 001, 005, 009, 012, 014, 040, 048, 053, 056, 057 Daewoo: 011, 013, 015, 017, 018, 019, 057, 078 Daytron: 078 Denon: 063 Dimensia: 001, 048 Electrohome: 010, 020, 065 Emerson: 003, 008, 010, 011, 017, 018, 020, 028, 039, 054, 057, 062, 065, 068, 072 Fisher: 007, 016, 021, 022, 023, 057, 064, 068, 070, 071, 079 Fuji: 004, 041 Funai: 018, 073 Garrard: 018 GE: 001, 002, 009, 040, 042, 048, 056 Go Video: 056, 059, 061, 081 Goldstar: 005, 010, 014, 054, 056, 065, 067 Gradiente: 018, 065 Harman Kardon: 005 Hitachi: 024, 025, 035, 037, 042, 063, 070, 080 JBL: 076 JC Penney: 005, 006, 007, 008, 009, 010, 023, 024, 025, 026, 035, 056, 061, 063, 065 Jensen: 024, 025, 037, 050 JVC: 005, 006, 007, 014, 037, 043, 062, 063, 068, 082 Kenwood: 005, 006, 007, 012, 014, 037, 043, 053, 068, 071 Kodak: 010 LG: 010 Lloyds: 053, 073, 079 Logik: 061 LXI: 010 Magnasonic: 061, 065, 078 Magnavox: 026, 027, 034, 044, 057, 061, 072 Marantz: 005, 006, 007, 012, 014, 026, 053, 067 Memorex: 007, 009, 010, 016, 018, 034, 049, 063, 065, 066, 068, 075, 079 MGA: 020, 028, 039 MGN: 056 Minolta: 024, 025, 035, 063 Mitsubishi: 020, 024, 025, 028, 039, 043, 065 Montgomery Ward: 049 Motorola: 049 MTC: 009, 046, 061 Multitech: 009, 012, 018 NEC: 005, 006, 007, 012, 014, 037, 043, 053, 054, 067, 070 Nikko: 010 Noblex: 009 Optimus: 010, 049, 065 Optonica: 031 Orion: 054, 057, 062, 065, 068, 072 Panasonic: 036, 045, 046, 057, 061, 072, 079 Pentax: 012, 024, 025, 035, 042, 053, 063 Pentex Research: 014 Philco: 026, 027, 063 Philips: 026, 031, 044, 057 Pioneer: 006, 024, 043, 055 Portland: 012, 013, 015 Proscan: 001, 002, 048 Proton: 061 Quasar: 045 Radio Shack: 010, 031, 065 Radio Shack/Realistic: 007, 009, 010, 016, 018, 020, 021, 022, 031, 049 Radix: 010 RCA: 001, 002, 003, 009, 024, 025, 029, 035, 040, 042, 045, 048, 055, 056, 063, 071, 083 Realistic: 007, 009, 010, 011, 016, 018, 020, 021, 022, 031, 049, 051, 056, 060, 065, 075, 079 Ricoh: 047 Runco: 034 Samsung: 009, 011, 038, 056, 073, 084 Sansui: 006, 037, 043, 061 Sanyo: 007, 009, 016, 054, 064, 068, 071, 075, 079, 085 Scott: 008, 011, 017, 028, 030, 057, 065, 072 Sears: 007, 010, 016, 021, 022, 023, 024, 025, 035, 053, 057, 063, 064, 065, 068, 071, 075, 079 Sharp: 013, 020, 031, 049, 051, 060, 066 Shintom: 004, 025, 032, 061 Signature: 049 Signature 2000: 075 Singer: 047, 061 Sony: 004, 032, 033, 041, 052, 058, 070, 074, 076, 077, 080 STS: 035 Sylvania: 018, 026, 027, 028, 044, 072 Symphonic: 018, 051, 053, 073, 079 Tandy: 007 Tashiko: 010 Tatung: 037 Teac: 018, 029, 037 Technics: 036 Teknika: 010, 018, 065 Toshiba: 000, 011, 021, 023, 024, 028, 030, 039, 057, 074, 078, 079 Totevision: 009, 010, 065 Unitec: 073 Unitech: 009 Vector Research: 005, 006, 011, 012, 053 Video Concepts: 005, 006, 011, 012, 039, 053 Wards: 009, 010, 011, 016, 018, 020, 024, 025, 031, 035, 049, 051, 056, 057, 060, 065, 066, 079 White Westinghouse: 073 XR-1000: 018 Yamaha: 005, 006, 007, 014, 037, 053 Zenith: 004, 032, 034, 041, 047, 069, 086 HTIB Lasonic: 083 Panasonic: 084 Venturer: 085 #01E_18-23_51HC85 23 05.4.28, 6:16 PM Black noitcudortnIr g otniitncoeMnr nuooCyl orte nhtocg e nitsoUmerr op tiung oniMttr euSoyr uor yog tinintoarMepOxidneppAx ednI23 (E) 51HC85, 57HC85, 65HC85 Setting up your Monitor Turning on the Monitor Press POWER on the remote control or monitor. The Red LED indicator on the monitor will be illuminated. Press POWER again to turn off the Monitor. Learning about the menu system After you have installed the batteries and programmed the remote control, you will need to set some preferences on the monitor by using the menu system. You can access the menu system using the buttons on the monitor or remote control. 1. Press MENU to display the menu system. 2. Press x or • to select a menu. 3. Press y or z to select an item, then press ENTER. 4. Press y or z to select or adjust a setting. 5. Press ENTER to activate the settings or display the next menu. 6. To close the menu, press EXIT. If you do not make a selection for a few seconds, the menu display will disappear automatically. : SELECT EXT : END Monitor front panel POWER #01E_24-26_51HC85 24 05.4.28, 6:16 PM Black VOLUME MENU EXIT INPUT POWERPOWER indicator Monitor front panel VOLUME MENU EXIT INPUT x •zy MENU EXIT (ENTER) INPUTRECALL POWER INFOP I CTURE MODE SPORTS P I CTURE SETT I NGS D I SPLAY FORMAT 1080i 1 2 3 C I NEMA MODE V I DEO CONVERGENCE 4 5 6 RESET SAVE P I CTURE SETT I NGS VIDEO MODESPORTS 7 8 9CONTRAST 100 BR I GHTNESS 5 0 +10 COLOR 5 0T I NT 0 100 0 ENT SHARPNESS 5 0 RESET SAVE : MOVE ENTER :SELECT TOPMENU PIC SIZE AUDIO AUDIO SETTINGS WOW SRS 3D ON OFF H I GH yzx • : SELECT E X I T : END ENTER MENU MENU DVDMENU FOCUS TruBass ENTER EXICT LEAR EXIT AUD I O SETT I NGS BASS TREBLE 5 0 5 0 BALANCE0 RESET noitcudortnIg niV tTcr eunonyoCl orte nhtocg e nitsoUmerr op tiung oniMttr euSoys ’Vs Tere uhttag enTVFiCBL/SAT CH VOL VCR ENTER sDVD UAUD I O MENU MUTE SLEEP RESET SAVE : MOVE : ADJUST TV/VCR PAUSE STOP PLAY FREEZE SOURCE SPLIT REW FF SKIP / SEARCH SWAP REC xLIGHT idneSET UP pLANGUAGE ENGLISH CLOCK SET 0 0 : 0 0 CT-90232 pCABLE A: SELECT EX I T : SELECT END CUSTOM SLEEP T I MER 0h00m CC OFF V I DEO LABEL BACKGROUND SHADED Note: You can change the background of the : SELECT EX I T:END menu. See page 46 for details.x LOCKS V - CH I P eNEW P I N CODE dnI: SELECT EXIT :END 24 (E) 51HC85, 57HC85, 65HC85 Changing the on-screen display language You can choose from three different languages (English, French, and Spanish) for the on-screen display of adjustment menus and messages. To select a language: 1. Press MENU, and then press x or • until the SET UP menu appears. 2. Press y or z to highlight LANGUAGE, and then press ENTER to display the pull-down menu. : SELECT ENTER :SET Monitor front panel VOLUME MENU EXIT INPUT x •zy MENU (ENTER) SET UP LANGUAGE ENGLISH CLOCK SET FRANÇAIS ESPAÑOL 1 2 3 3. Press y or z to highlight your desired language. 4 5 6 Adjusting the color convergence 7 8 9100 0 ENT This projection monitor uses three separate picture tubes: red, green, and blue. The red, green, and blue images are projected onto the screen where they converge to form a full-color picture. You can see a clear picture only when the three images converge correctly. yzx • Convergence may drift over time or if you move the monitor. If you can see clear images on your monitor screen, skip this procedure. It is recommended that the adjustment is made only after the ENTER monitor has been on for at least 30 minutes. 1. Press MENU, and then press x or • until the PICTURE menu appears. 2. Press y or z to highlight CONVERGENCE, and then press ENTER to display the pull-down menu. 3. Press y or z to highlight ADJUST, and then press ENTER. The monitor will enter 56-point convergence mode. ADJUST RESET : START (continued on next page) INPUTRECALL POWER INFO+10 TOP MENU PIC SIZE ENTER MENU MENU DVDMENU ENTER EXICT LEAR TVCBL/SAT CH VOL VCR DVD POP DIRECT CH MUTE SLEEP TV/VCR PAUSE STOP PLAY FREEZE SOURCE SPLIT REW FF SKIP / SEARCH CH SCAN SWAP POP CHREC LIGHT cursor #01E_24-26_51HC85 25 05.4.28, 6:16 PM Black P I CTURE MODE P I CTURE SETT I NGS D I SPLAY FORMAT C I NEMA MODE CONVERGENCE RESET SAVE : SELECT ENTER : TO SELECT POS I T I ON If you see separate red, blue, or green crossed lines (or red or blue shadows next to white lines), you need to adjust the convergence. 4. Press yzx • to move the cursor to the position you want to adjust. 5. Press ENTER repeatedly to select RED or BLUE adjusting mode (red crossed lines or blue crossed lines), depending on which color needs adjusting. ENTER : TO ADJUST CONVERGENCE EX I T : TO F I N I SH ADJUSTMENT noitcudortnIr g otniitncoeMnr nuooCyl orte nhtocg e nitsoUmerr op tiung oniMttr euSoyr uor yog tinintoarMepOxidneppAx ednI25 (E) 51HC85, 57HC85, 65HC85 6. Press y (up), z (down), x (left), or • (right) on the remote control to converge the red or blue line into the white line. EX I T : TO F I N I SH ADJUSTMENT INPUTRECALL POWER INFO1 2 3 4 5 6 : TO ADJUST RED : TO ADJUST BLUE 7 8 9ENTER : TO CHANGE COLOR EX I T : TO F I N I SH ADJUSTMENT 100 +10 0 ENT 7. If both red and blue need adjusting, you will need to perform PIC SIZE steps 5 and 6 twice. 8. Press ENTER to display the cursor. 9. Repeat steps 4-8 to adjust another position. EXIT 10. Press EXIT to close the convergence screen. To reset your adjustments: 1. Select RESET in step 3 on page 25, and then press ENTER. The message “WARNING: RESETS USER ADJUSTMENT TO STOP FACTORY SETTINGS” will appear. 2. Press y or z to highlight START, and then press ENTER. Your convergence settings have been reset. : SELECT ENTER : START ENTER : TO SELECT POS I T I ON TOPMENU MENU yzx • ENTER CLEAR ENTER #01E_24-26_51HC85 26 05.4.28, 6:16 PM Black MENU DVDMENU ENTER TVCBL/SAT VCR DVD noitcudortnIg niV tTcr eunonyoCCH VOL l POP DIRECT CH MUTE SLEEP orte TV/VCR PAUSE PLAY nhtoFREEZE SOURCE SPLIT REW FF SKIP / SEARCH cg CH SCAN SWAP POP CHe nitREC LIGHT soUmerCONVERGENCE RESET ADJUSTMENT CANCEL START r oWARN I NG : RESETS USER ADJUSTMENT p tTO FACTORY SETT I NGS iunRESET SAVEg oniMttr euSoys ’Vs Tere uhttag enFisUxidneppAx ednI26 (E) 51HC85, 57HC85, 65HC85 Operating your Monitor Viewing the wide-screen picture formats (480i, 480p, and 1080i signals only) You can view 480i, 480p, and 1080i format programs in a variety of picture sizes—Natural, TheaterWide 1, TheaterWide 2, TheaterWide 3, and Full. (The Full picture size is not selectable for 1080i format programs.) The way the image displays in any of the picture sizes will vary depending on the format of the program you are viewing. Select the picture size that displays the current program the way that looks best to you. See “Notice of possible adverse effects on monitor picture display,” below right. Selecting the picture size 1. Press PIC SIZE on the remote control. 2. Press the corresponding number button (0-4) or press y or z to select the desired picture size, as described below and on the next page. P I CTURE S I ZE 0 : NATURAL 1 : THEATERWIDE 1 2 : THEATERWIDE 2 3 : THEATERWIDE 3 4 : FULL 0 – 4 : TO SELECT Natural picture size (continued on next page) INPUTRECALL POWER INFO1 2 3 4 5 6 7 8 9+10 100 0 ENT PIC SIZE EXIT STOP Number Natural picture size example: The way the image displays will vary depending on the format of the program you are currently watching. TOP MENU MENU ENTER CLEAR PIC SIZE DVDMENU yzENTER TVCBL/SAT VCR DVD CH VOL POP DIRECT CH MUTE SLEEP TV/VCR PAUSE PLAY Note: REW FREEZE FF SOURCE SPLIT SKIP / SEARCH You selecting CH also REC SCAN can PICTURE SWAP change POP CHLIGHT SIZE the picture in the PICTURE size by menu. P I CTURE P I CTURE S I ZEAUTO ASPECT OFF P I CTURE SCROLL RESET SAVE : MOVE ENTER :START Conventional picture on a conventional monitor screen NOTICE OF POSSIBLE ADVERSE EFFECTS ON MONITOR PICTURE DISPLAY Avoid displaying stationary images on your monitor screen for extended periods of time. Fixed (non-moving) patterns or images (including but not limited to PIP/ POP windows, closed captions, video game patterns, TV station logos (from VCR, etc.), stock tickers, websites, and special formats that do not use the entire screen) can become permanently ingrained in the cathode ray tube(s) of the monitor and cause subtle but permanent ghost images. This type of damage is NOT COVERED BY YOUR WARRANTY. See item 33 on page 4 for details. #01E_27-33_51HC85 27 05.4.28, 6:16 PM Black Conventional picture in Natural size on your wide-screen monitor noitcudortnIr g otniitncoeMnr nuooCyl orte nhtocg e nitsoUmerr op tiung oniMttr euSoyr uor yog tinintoarMepOxidneppAx ednI27 (E) 51HC85, 57HC85, 65HC85 TheaterWide 1 picture size (For 4:3 format programs) • The picture is non-uniformly enlarged—the center of the picture remains close to its original proportion, but the left and right edges are stretched wider to fill the screen. • A small part of the picture at the top and bottom is hidden; however, this mode cannot be scrolled. TheaterWide 2 picture size (For letter box programs) • The entire picture is uniformly enlarged—it is stretched the same amount both wider and taller (retains its original proportion). • Part of the picture at the top and bottom is hidden. To view the hidden areas, see “Scrolling the TheaterWide® picture” on page 29. TheaterWide 3 picture size (For letter box programs with subtitles) • The picture is non-uniformly enlarged—it is stretched wider to fill the width of the screen, but only slightly stretched taller. • A small part of the picture at the top and bottom is hidden. To view the hidden areas (such as subtitles or captions), see “Scrolling the TheaterWide® picture” on page 29. Full picture size (For 16:9 format programs) • If you are receiving a 4:3 format program, the picture is stretched wider to fill the width of the screen, but not stretched taller. • None of the picture is hidden. Note: • To select the picture size, press PIC SIZE on the remote control or select PICTURE SIZE in the PICTURE menu. • The PICTURE SIZE feature is not available for some program formats (such as 720p). Such formats will display in Natural picture size (see page 27). • If you select TheaterWide 2 or 3, the top and bottom edges of the picture may be hidden. To see the hidden edges, either scroll the picture (see page 29) or try viewing the program in Full picture size. TheaterWide 1 picture size example TheaterWide 3 picture size example NOTICE OF POSSIBLE ADVERSE EFFECTS ON MONITOR PICTURE DISPLAY Avoid displaying stationary images on your monitor screen for extended periods of time. Fixed (non-moving) patterns or images (including but not limited to PIP/ POP windows, closed captions, video game patterns, TV station logos (from VCR, etc.), stock tickers, websites, and special formats that do not use the entire screen) can become permanently ingrained in the cathode ray tube(s) of the monitor and cause subtle but permanent ghost images. This type of damage is NOT COVERED BY YOUR WARRANTY. See item 33 on page 4 for details. #01E_27-33_51HC85 28 05.4.28, 6:16 PM Black noitcudortnIg niV tTcr eunonyoCl orte nhotCg e ntisoA B C D E F G - - - - - - - - - - - - - - - - UmeRp uV Tg r niutTheaterWide 2 picture size example toeySr uor yNote: og tiA B C D E F G - - - - - - - - - - - - - - - - Using these functions to change the nintopicture size (i.e., changing the height/ arMwidth ratio) for any purpose other than epyour private viewing may be prohibited Ounder Copyright Law of the United States and other countries, and may subject you to civil and criminal liability. xA B C D E F G - - - - - - - - - - - - - - - - - - - - - - - - - - idneppAx ednIFull picture size example 28 (E) 51HC85, 57HC85, 65HC85 Scrolling the TheaterWide® picture (TheaterWide 2 and 3 only) 1. Press PIC SIZE to select the TheaterWide 2 or TheaterWide 3 mode. 2. Press MENU, and then press x or • until the PICTURE menu appears. 3. Press y or z to highlight PICTURE SCROLL. : MOVE ENTER : START INPUTRECALL POWER INFO +10 PIC SIZE EXIT TVCBL/SAT VCR DVD 1 2 3 4 5 6 7 8 9100 0 ENT P I CTURE P I CTURE S I ZE AUTO ASPECT OFF TOPMENU PIC SIZE P I CTURE SCROLL MENU RESET SAVE 4. Press ENTER to display the Scroll Adjustment mode. ENTER CLEAR ENTER Note: SCROLL ADJUSTMENT 0 You can scroll the picture in TheaterWide 2 : TO ADJUST and TheaterWide 3 modes only. The scroll amounts are as follows: • 480i/480p/1080i signal source: 5. Press y or z to adjust the vertical position of the picture. • Normal (center) position TheaterWide 1 : Not adjustable TheaterWide 2 : -10 to +20 TheaterWide 3 : -10 to +20 NOTICE OF POSSIBLE ADVERSE SCROL L AD JUSTMENT 0 EFFECTS ON MONITOR PICTURE : TO ADJUST DISPLAY Avoid displaying stationary images on your monitor screen for extended periods • To raise the picture, press y . of time. Fixed (non-moving) patterns or images (including but not limited to PIP/ POP windows, closed captions, video game patterns, TV station logos (from VCR, etc.), stock tickers, websites, and special formats that do not use the entire SCROLL ADJUSTMENT +20 screen) can become permanently : TO ADJUST ingrained in the cathode ray tube(s) of the monitor and cause subtle but permanent ghost images. This type of damage is NOT COVERED BY YOUR • To lower the picture, press z. WARRANTY. See item 33 on page 4 for details. SCROLL ADJUSTMENT –10 : TO ADJUST #01E_27-33_51HC85 29 05.4.28, 6:16 PM Black MENU DVDMENU yzx • ENTER CH VOL noitcudortnIr g otniitncoeMnr nuooCyl orte nhtocg e nitsoUmerr op tiung oniMttr euSoyr uor yog tinintoarMepOxidneppAx ednI29 (E) 51HC85, 57HC85, 65HC85 Using the AUTO ASPECT feature When the AUTO ASPECT feature is set to ON and the monitor receives a 480i signal (other than an HDMI input source), the picture size is automatically selected (as described in the following table). If the signal does not include aspect information, the picture size you selected on pages 27–28 is displayed. To turn on the AUTO ASPECT feature: 1. Press MENU, and then press x or • until the PICTURE menu appears. : SELECT EX I T : END Note: The AUTO ASPECT feature is available for additional formats when viewing HDMI sources because AUTO ASPECT operates Automatic aspect size Aspect ratio of signal source (automatically selected based on information found in the digital HDMI signal (not ID-1 data). when AUTO ASPECT is ON) 4:3 Normal Natural 16:9 Full Full 4:3 Letter box TheaterWide 2 Not defined (no ID-1 data) User-set mode NOTICE OF POSSIBLE ADVERSE EFFECTS ON MONITOR PICTURE DISPLAY Avoid displaying stationary images on your monitor screen for extended periods of time. Fixed (non-moving) patterns or images (including but not limited to PIP/ POP windows, closed captions, video game patterns, TV station logos (from VCR, etc.), stock tickers, websites, and special formats that do not use the entire screen) can become permanently ingrained in the cathode ray tube(s) of the monitor and cause subtle but permanent ghost images. This type of damage is NOT COVERED BY YOUR WARRANTY. See item 33 on page 4 for details. #01E_27-33_51HC85 30 05.4.28, 6:16 PM Black INPUTRECALL POWER INFO1 2 3 4 5 6 7 8 9+10 100 0 ENT TOP MENU PIC SIZE ENTER MENU MENU DVDMENU EXICT LEAR STOP yzx • P I CTURE ENTER MODE SPORTS P I CTURE SETT I NGS ENTER D I SPLAY FORMAT 1080i C I NEMA MODE V I DEO CONVERGENCE RESET SAVE TVCBL/SAT VCR DVD 2. Press y or z to highlight AUTO ASPECT, and then press ENTER. ENTER : SET CH VOL POP DIRECT CH MUTE SLEEP TV/VCR PAUSE PLAY FREEZE SOURCE SPLIT REW FF SKIP / SEARCH CH SCAN SWAP POP CHREC LIGHT P I CTURE S I ZEnoitcudortnIg niV tTcr eunonyoCl orte nhotCg e ntisoUmeRp uV Tg r niuttoeySP I CTURE AUTO ASPECT OFF ON P I CTURE SCROLL r uor yRESET SAVE og ti: SELECT nintoar3. Press y or z to select ON, and then press ENTER. MepOxidneppAx ednI30 (E) 51HC85, 57HC85, 65HC85 Using the POP double-window feature The POP (picture-out-picture) feature splits the screen into a double window that allows you to watch two external input sources (for example, a VCR and DVD player) at the same time. To display a picture from an external source in the POP window: 1. Connect the external source equipment (see “Connecting your Monitor” on page 8). 2. Press INPUT to select the external input source you want to watch in the main window. 3. Press SPLIT to display the POP window. MAIN POP VIDEO 1 VIDEO 2 4. Repeatedly press SOURCE to select the input source for the POP window (VIDEO 1, VIDEO 2, VIDEO 3, ColorStream® HD1, ColorStream® HD2, or HDMI). The current source will display in purple. 5. You can play a tape as the POP picture, or select a channel for the POP window using the VCR’s remote control. POP SOURCE SELECT I ON V1 : 2 3 : : V I DEO 1 4 : ColorStream HD1 5 : ColorStream HD2 Note: • You can display only 480i format programs in the Main window. • You can choose to output the sound of either the main or POP program through the AUDIO OUT terminals (see “Selecting the Audio OUT sound” on page 46). • You can choose to hear the main or POP audio through the monitor speakers (See “Switching the speaker audio (main or POP program)” on page 32). • HDMI, 720p ColorStream, 480p ColorStream, and 1080i ColorStream signals will only display in the POP (right) window. These signals will not display in the Main window (480i only) main (left) window when the monitor is in double-window mode. • If an HDMI or ColorStream source is being viewed when you open the POP double- window feature, the HDMI or ColorStream source will default to the POP (right) window. INPUT NOTICE OF POSSIBLE ADVERSE EFFECTS ON MONITOR PICTURE DISPLAY Avoid displaying stationary images on your monitor screen for extended periods of time. Fixed (non-moving) patterns or images (including but not limited to PIP/ POP windows, closed captions, video game patterns, TV station logos (from VCR, etc.), stock tickers, websites, and special formats that do not use the entire screen) can become permanently ingrained in the cathode ray tube(s) of the monitor and cause subtle but permanent ghost images. This type of damage is NOT COVERED BY YOUR WARRANTY. See item 33 on page 4 for details. #01E_27-33_51HC85 31 05.4.28, 6:16 PM Black POP window INPUTRECALL POWER INFO1 2 3 4 5 6 7 8 9+10 100 0 ENT PIC SIZE EXIT EXIT STOP Number I DEO V I DEO 2 3 6 : HDM I 1 - 6 : TO SELECT While the above menu is on the screen, you can select the desired input source by pressing the corresponding number button (1-6). If the V-CHIP feature is active and you try to watch an input source that exceeds your set rating limits, the program will be blocked (see “Using the V-CHIP menu” on page 33). BLOCKED TOP MENU MENU DVDMENU ENTEER NTER CLEAR TVCBL/SAT VCR DVD CH VOL MUTE SLEEP TV/VCR PAUSE PLAY SPLIT FREEZE SOURCE SPLIT REW FF SKIP / SEARCH SOURCE SWAP REC LIGHT POP24 To close the POP window: Press SPLIT again or EXIT. noitcudortnIr g otniitncoeMnr nuooCyl orte nhtocg e nitsoUmerr op tiung oniMttr euSoyr uor yog tinintoarMepOxidneppAx ednI31 (E) 51HC85, 57HC85, 65HC85 Swapping the main and POP pictures Press SWAP while you are using the POP feature to swap the position of the main and POP pictures. Switching the speaker sound (main or POP program) Press x or • while you are using the POP feature to switch the sound (main or POP) from the speakers. The POP sound is monaural only. The selected input source indicator is displayed in purple. MAIN POP VIDEO 1 VIDEO 2 Note: • If the POP program is not 480i format, it will not display in the main window when you press SWAP. • The VARIABLE AUDIO OUT terminals will switch with the speaker sound. However, the source of the regular AUDIO OUT terminals is determined by the AUDIO OUT menu setting (page 46). The regular AUDIO OUT terminals do not switch with the speaker sound. Note: • The AUTO ASPECT feature (page 30) does not operate in double-window mode. • Aspect ratio is the ratio of width to height of the picture. NOTICE OF POSSIBLE ADVERSE EFFECTS ON MONITOR PICTURE DISPLAY Avoid displaying stationary images on your monitor screen for extended periods of time. Fixed (non-moving) patterns or images (including but not limited to PIP/ POP windows, closed captions, video game patterns, TV station logos (from VCR, etc.), stock tickers, websites, and special formats that do not use the entire screen) can become permanently ingrained in the cathode ray tube(s) of the monitor and cause subtle but permanent ghost images. This type of damage is NOT COVERED BY YOUR WARRANTY. See item 33 on page 4 for details. #01E_27-33_51HC85 32 05.4.28, 6:16 PM Black +10 CHRTN 100 0 ENT Example: Press x Example: Press • TOP MENU PIC SIZE ENTER EXICT LEAR STOP purple MENU DVDMENU x • ENTER MAIN POP TVCBL/SAT VIDEO 1 VIDEO 2 VCR DVD Double-Window aspect ratio The Double-Window feature displays each picture according to its input signal aspect ratio, as illustrated below. 480i 480i 480i 480p/720p/1081i noitcudortnIg niV tTcr eunonyoCl orte nhotCg e ntisoUmeRCH VOL MUTE SLEEP TV/VCR PAUSE PLAY purple FREEZE SOURCE SPLIT SWAP p REW FF SKIP / SEARCH uV SWAP Tg REC LIGHT r niuttoeySr uor yog tinintoarMepOxidneppAx ednI32 (E) 51HC85, 57HC85, 65HC85 Using the LOCKS menu The LOCKS menu includes the V-Chip and New PIN Code functions. You can use these functions after entering the correct PIN code. Entering the PIN code 1. Press MENU, and then press x or • until the LOCKS menu appears. : SELECT EXIT :END Note: The V-Chip function is available only for the U.S. V-Chip system. The Canadian V-Chip system is not supported. (continued on next page) #01E_27-33_51HC85 33 05.4.28, 6:16 PM Black INPUTRECALL POWER INFO+10 PIC SIZE EXIT STOP RECALL Number MENU • Blocking Reset status: Set your 4-digit code by pressing the Number buttons (0–9). 1 2 3 LOCKS V - CH I P NEW P I N CODE 4 5 6 7 8 9100 0 ENT TOP MENU 2. Press y or z to display the PIN code entering mode. MENU • When the PIN code is already stored: DVDMENU Press the Number buttons (0-9) to enter the 4-digit PIN code used for blocking ENTER channels. CLEAR BLOCK I NG RESET 0–9: SELECT ENTER : SET yzx • ENTER ENTER TVCBL/SAT VCR DVD CH VOL POP DIRECT CH MUTE SLEEP LOCKS LOCKS P I N CODE 1110 P I N CODE 1234 TV/VCR PAUSE REW FF SKIP / SEARCH 0–9 : SELECT ENTER : SET If the wrong PIN code is entered, the message “Incorrect” appears. Enter the code again, and then press ENTER. If you cannot remember your PIN code 1. While the PIN code entering screen is displayed, press RECALL four times within five seconds. The PIN code will be released (Blocking Reset status restored). 2. Enter a new 4-digit code, and then press ENTER. The LOCKS menu appears. V - CH I P BLOCK I NG ACT I VE PLAY FREEZE SOURCE SPLIT CH SCAN SWAP POP CHREC LIGHT LOCKS NEW P I N CODE : MOVE ENTER : START Using the V-CHIP menu Some movies and TV programs include signals that classify the content of the program (violence, sex, dialog, language). The V-CHIP control feature in this monitor detects the signals and blocks the programs according to your selections. To use this feature, perform the following setup. noitcudortnIr g otniitncoeMnr nuooCyl orte nhtocg e nitsoUmerr op tiung oniMttr euSoyr uor yog tinintoarMepOxidneppAx ednI33 (E) 51HC85, 57HC85, 65HC85 ENABLE BLOCKING 1. From the LOCKS menu (page 33), press z or y to highlight V- CHIP, and then press ENTER. The V-CHIP menu appears. 2. Press z or y to highlight ENABLE BLOCKING, and then press ENTER. 3. Press y or z to select ON or OFF. ON : To enable your setting (Lock) OFF: To release your setting (Unlock) TV RATING (Independent rating system for broadcasters) 1. From the V-CHIP menu, press z or y to highlight TV RATING, and then press ENTER. The TV RATING menu appears. 2. Press z or y to select an item. 3. Press • to lock (displays “X” ) Press x to unlock (displays “✓ ”) 4. Repeat steps 2 and 3 to set the next item. The TV age-based ratings and content themes you can lock are listed in the table below. Ratings Description and Content themes MA Mature Audience Only (This program is specifically designed to be viewed by adults and therefore may be unsuitable for children under 17.) L) Crude or indecent language S) Explicit sexual activity V) Graphic violence 14 Parents Strongly Cautioned (This program contains some material that many parents would find unsuitable for children under 14 years of age.) D) Intensely suggestive dialog L) Strong, coarse language S) Intense sexual situations V) Intense violence PG Parental Guidance Suggested (This program contains material that parents may find unsuitable for younger children.) D) Some suggestive dialog L) Infrequent coarse language S) Some sexual situations V) Moderate violence G General Audience (Most parents would find this program suitable for all ages.) Y7, Directed to Older Children (This program is designed for Y7FV children age 7 and above. Note: Programs in which fantasy violence may be more intense or more combative than other programs in this category are designated Y7FV.) Y All Children (This program is designed to be appropriate for all children.) LOCKS menu V-CHIP menu V - CH I P #01E_34-36_51HC85 34 05.4.28, 6:17 PM Black LOCKS NEW P I N CODE V – CH I P ENABLE BLOCK I NG ONTV RAT I NG OFF MPAA RAT I NG : MOVE ENTER : START BLOCK I NG OPT I ON LOCKS MENU : SELECT ENTER : SET RECALL TV RATING menu INPUTRECALL POWER INFO1 2 3 4 5 6 7 8 9TV RAT I NG MA14 GPG D I ALOG +10 LANGUAGE X X SEX X X 100 0 ENT V I OLENCE X X NO DLSV X X Y7FV Y7 Y YOUTH TV RAT I NG V – CH I P MENU TOP MENU PIC SIZE : MOVE :SELECT MENU ENTER noitcudortnIg niV tTcr eunonyoCl orte nhotCg e ntisoUmeRp uV Tg r niuttoeySDVDMENU yzx • ENTER EXICT LEAR ENTER TVCBL/SAT CH VOL r VCR uDVD or yPOP DIRECT CH MUTE SLEEP og tiTV/VCR PAUSE STOP PLAY nintoFREEZE SOURCE SPLIT aREW FF SKIP / SEARCH rMeCH SCAN SWAP POP CHREC LIGHT pOPress RECALL to display the rating of the TV program you are currently watching. xidnepPGTV PG– L V pLAV FULL VCR VIDEO 1 33 34 35 x ednI34 (E) 51HC85, 57HC85, 65HC85 MPAA RATING (Independent rating system for movies) 1. From the V-CHIP menu (page 34), press z or y to highlight MPAA RATING, and then press ENTER. The MPAA RATING menu appears. 2. Press y or z to highlight MPAA RATING. 3. Press • to lock (“X”) or press x to unlock (“✓”). The movie ratings you can lock are described as follows: X : X-rated (For adults only) NC17: Not intended for anyone 17 and under R : Restricted (Under 17 requires accompanying parent or adult guardian.) PG13 : Parents Strongly Cautioned (Some material may be inappropriate for children under 13) PG : Parental Guidance Suggested (Some material may not be suitable for children) G : General Audience (Appropriate for all ages) BLOCKING OPTION 1. From the V-CHIP menu (page 34), press z or y to highlight BLOCKING OPTION, and then press ENTER. The BLOCKING OPTION menu appears. 2. Press y or z to select an item, as discribed below: MPAA UNRATED: 1. Highlight MPAA UNRATED, and then press ENTER. 2. Press y or z to select ON (Lock) or OFF (Unlock) for unrated programs in the MPAA rating system, then press ENTER. ENABLE BLOCK I NG ON V-CHIP menu MPAA RATING menu ENABLE BLOCK I NG ON #01E_34-36_51HC85 35 05.4.28, 6:17 PM Black V – CH I P TV RAT I NG MPAA RAT I NG BLOCK I NG OPT I ON LOCKS MENU MPAA RAT I NG X NC17 R PG13 PG G MPAA RAT I NG X X X V – CH I P MENU : MOVE ENTER : START : MOVE :SELECT INPUTRECALL POWER INFO1 2 3 4 5 6 7 8 9+10 100 0 ENT TOP MENU PIC SIZE MENU DVDMENU yzx • V – CH I P BLOCK I NG OPT I ON ENTEER NTER EXICT LEAR TV RAT I NG TV NONE RAT I NG MPAA RAT I NG V – CH I P MENU BLOCK I NG OPT I ON LOCKS MENU : MOVE ENTER : START : SELECT ENTER : SET STOP TV NONE RATING: 1. Highlight TV NONE RATING, and then press ENTER. Caution: Be aware that setting the TV None Rating to ON may block the broadcast of emergency 2. Press y or z to select ON (Lock) or OFF (Unlock) for programs information.The menu will display the note, rated NONE in the TV PARENTAL GUIDELINES, then press “Enabling this option may block emergency ENTER. messages” to warn you of this possibility. MPAA UNRATED NOTE : ENABL I NG TH I S OPT I ON MAY BLOCK EMERGENCY MESSAGES MPAA UNRATED ONOFF TVENTER CBL/SAT VCR DVD CH VOL POP DIRECT CH MUTE SLEEP TV/VCR PAUSE PLAY FREEZE SOURCE SPLIT REW FF SKIP / SEARCH CH SCAN SWAP POP CHREC LIGHT BLOCK I NG OPT I ON ONTV NONE RAT I NG V – CH I P MENUOFF : SELECT ENTER : SET V-CHIP MENU: Highlight V-CHIP menu, then press ENTER to return to the V-CHIP menu. noitcudortnIr g otniitncoeMnr nuooCyl orte nhtocg e nitsoUmerr op tiung oniMttr euSoyr uor yog tinintoarMepOxidneppAx ednI35 (E) 51HC85, 57HC85, 65HC85 Changing the PIN code 1. From the LOCKS menu (page 33), press y or z to highlight NEW PIN CODE. 2. Press the Number buttons (0-9) to enter a new 4-digit code. The numbers you enter will replace the dashes in the display. V - CH I P 0–9: SELECT ENTER : SET Monitor front panel VOLUME MENU EXIT INPUT x •zy MENU (ENTER)#01E_34-36_51HC85 36 05.4.28, 6:17 PM Black LOCKS NEW P I N CODE 2562 3. Press ENTER. The new PIN code is now active. Adjusting the picture Selecting the picture mode You can select your desired picture type from four picture modes: Sports, Standard, Movie, and Preference. (see “Saving your new preferences” on page 37.) To select the picture mode: 1. Press MENU, and then press x or • until the PICTURE menu appears. 2. Press z or y to highlight MODE, and then press ENTER. 3. Press z or y to select the mode you prefer, then press ENTER. INPUTRECALL POWER INFO 1 2 3 4 5 6 7 8 9+10 100 0 ENT PIC SIZE EXIT POP DIRECT CH MUTE SLEEP Number Mode Picture Quality Sports Bright and dynamic picture (factory setting) Standard Standard picture setting (factory setting) Movie Movie-like picture setting (factory setting) Preference Your personal preference : SELECT ENTER :SET TOPMENU MENU DVDMENU yzx • ENTEENR TER CLEAR ENTER TVCBL/SAT VCR DVD noitcudortnIg niV tTcr eunonyoCl orte nhotCg e ntisoUmeRCH VOL p uV Tg r niuttoeyNote: SIf you select one of the factory-set picture modes (SPORTS, STANDARD, or MOVIE) and then change a picture quality setting (for example, increase the contrast), the picture r mode automatically changes to uP I CTURE oMODE SPORTS PREFERENCE in the Picture menu. r yP I CTURE SETT I NGS STANDARD oD I SPLAY FORMAT MOV I E To save your new picture quality settings, you g tC I NEMA MODE PREFERENCE inCONVERGENCE inmust select SAVE (see page 37) before toaRESET SAVE closing the Picture menu or the monitor will rMereturn to the previous picture mode. pOxidneppAx ednI36 (E) 51HC85, 57HC85, 65HC85 Adjusting the picture quality You can adjust the picture quality to your personal preferences, including the contrast, brightness, color, tint, sharpness, and color temperature. To adjust the picture quality: 1. Press MENU, and then press x or • until the PICTURE menu appears. 2. Press z or y to highlight PICTURE SETTINGS, then press ENTER. The PICTURE SETTINGS menu appears. 3. Press y or z until the item you want to adjust is highlighted, then press ENTER. 4. Press x or • to adjust the level. The PICTURE settings you adjusted can be saved in the PICTURE SETTINGS menu’s PREFERENCE mode. You can select your settings (PREFERENCE mode) or choose one of the factory-set modes, as described on page 36. Saving your new preferences You can save the PICTURE settings you adjusted (contrast, brightness, color, tint, sharpness, color temperature and CableClear DNR) in the PICTURE SETTINGS menu’s PREFERENCE mode. To save your new preferences: 1. Press MENU, and then press x or • until the PICTURE menu appears. 2. Press y or z to highlight PICTURE SETTINGS, and then press ENTER. The PICTURE SETTINGS menu appears. 3. Press yzx • to highlight SAVE, and then press ENTER. When complete, “SAVE” changes to “DONE” in the menu and the picture mode automatically changes to PREFERENCE (see “Selecting the picture mode” on page 36). : MOVE ENTER :START Monitor front panel Selection x Pressing • MENU VOLUME EXIT INPUT contrast lower higher brightness darker lighter color paler deeper tint reddish greenish sharpness softer sharper color temperature cool medium warm x •zy MENU (ENTER) 1 2 3 4 5 6 7 8 9100 0 ENT CONTRAST 7 5 ENTER #01E_37-41_51HC85 37 05.4.28, 6:17 PM Black INPUTRECALL POWER INFOP I CTURE SETT I NGS VIDEO MODEPREFERENCE +10 CONTRAST 1 0 0 BR I GHTNESS 5 0 COLOR 5 0T I NT 0 SHARPNESS 5 0 TOP MENU PIC SIZE RESET SAVE : MOVE ENTER :SELECT MENU MENU DVDMENU yzx • ENTEER NTER EXICT LEAR TVCBL/SAT CH VOL VCR DVD POP DIRECT CH MUTE SLEEP TV/VCR PAUSE STOP PLAY FREEZE SOURCE SPLIT REW FF SKIP / SEARCH CH SCAN SWAP POP CHREC LIGHT P I CTURE SETT I NGS MODECOLOR TEMPERATURE VIDEO PREFERENCE COOL P CableClear I CTURE MENU DNR OFF RESET DONE noitcudortnIr g otniitncoeMnr nuooCyl orte nhtocg e nitsoUmerr op tiung oniMttr euSoyr uor yog tinintoarMepOxidneppAx ednI37 (E) 51HC85, 57HC85, 65HC85 Selecting the color temperature You can change the quality of the picture by selecting from three preset color temperatures: cool, medium, and warm. To select the color temperature: 1. Press MENU, and then press x or • until the PICTURE menu appears. 2. Press y or z to highlight PICTURE SETTINGS, and then press ENTER. The PICTURE SETTINGS menu appears. 3. Press y or z to highlight COLOR TEMPERATURE, and then press ENTER. : MOVE ENTER : SELECT INPUTRECALL POWER INFO1 2 3 Mode Picture Quality 4 5 6 cool bluish medium neutral 7 8 9+10 warm reddish 100 0 ENT PIC SIZE EXIT STOP #01E_37-41_51HC85 38 05.4.28, 6:17 PM Black TOPMENU MENU MENU DVDMENU yzx • ENTEENR TER CLEAR ENTER TVCBL/SAT CH VOL VCR DVD POP DIRECT CH MUTE SLEEP TV/VCR PAUSE PLAY FREEZE SOURCE SPLIT P I CTURE SETT I NGS VIDEO REW FF SKIP / SEARCH MODEPREFERENCE COLOR TEMPERATURE COOL CableClear DNR OFF CH SCAN SWAP POP CHREC LIGHT P I CTURE MENU RESET SAVE 4. Press x or • to select the mode you prefer. Using the CableClear® DNR feature CableClear® DNR reduces visible interference in your monitor picture. This is useful when receiving a broadcast with a weak signal Note: (especially a Cable channel) or playing a video cassette or disc • When the monitor is in ColorStream or damaged by repeated use. To turn on CableClear® DNR: 1. Press MENU, and then press x or • until the PICTURE menu appears. noitcudortnIg niV tTcr eunonyoCl orte nhotCg e ntisoUmeRp uV Tg r niuttoeySHDMI mode, the words “CableClear DNR” will change to “DNR” in the menu. • DNR is not selectable when the monitor is r uin HDMI mode. or yog t2. Press y or z to highlight PICTURE SETTINGS, and then press inintENTER. oarMThe PICTURE SETTINGS menu appears. ep3. Press y or z to highlight CableClear DNR, and then press OENTER. xiP I CTURE SETT I NGS VIDEO dMODEPREFERENCE nCOLOR TEMPERATURE COOL CableClear DNR eOFF P I CTURE MENU pRESET SAVE pA: MOVE ENTER : SELECT 4. Press x or • to select AUTO. To turn off CableClear® DNR: Select OFF in step 4 above. x ednI38 (E) 51HC85, 57HC85, 65HC85 Resetting your picture setting adjustments The RESET function adjusts the picture settings to the following factory settings: Mode ........................... sports Contrast ................ max (100) Brightness ............ center (50) Color ................... center (50) To reset your picture setting adjustments: 1. Press MENU, and then press x or • until the PICTURE menu appears. 2. Press y or z to highlight PICTURE SETTINGS, and then press ENTER. The PICTURE SETTINGS menu appears. 3. Press y or z to highlight RESET. 4. Press ENTER. “RESET” changes to “DONE” in the menu. Selecting the display format (for 480p signals only) You can use this feature to convert 480p input signals to 540p or 1080i. To select the display format: 1. Press MENU, and then press x or • until the PICTURE menu appears. 2. Press y or z to highlight DISPLAY FORMAT, and then press ENTER. 3. Press y or z to select 540p or 1080i, whichever you prefer. INPUTRECALL POWER Tint ....................... center (0) INFOSharpness ............. center (50) Color temperature ........... cool CableClear DNR ........... auto +10 PIC SIZE EXIT STOP #01E_37-41_51HC85 39 05.4.28, 6:17 PM Black 1 2 3 4 5 6 7 8 9100 0 ENT TOP MENU ENTER CLEAR MENU yzx • ENTER Selecting the cinema mode When you view a DVD movie (3:2 pulldown processed or interlaced mode) from a DVD player connected to the ColorStream (component video) inputs on the monitor, smoother and more natural motion can be obtained by setting the CINEMA MODE to FILM. To set the CINEMA MODE to FILM: 1. Press MENU, and then press x or • until the PICTURE menu appears. 2. Press y or z to highlight CINEMA MODE, and then press ENTER. 3. Press y or z to select FILM. To turn off the CINEMA MODE: Press y or z to select VIDEO in step 3 above. MENU DVDMENU ENTER TVP I CTURE SETT I NGS MODECOLOR TEMPERATURE VIDEO CBL/SAT CH VOL VCR DVD : SELECT ENTER :SET SPORTS COOL CableClear DNR P I CTURE MENU AUTO DONE SAVE POP DIRECT CH MUTE SLEEP TV/VCR PAUSE PLAY FREEZE SOURCE SPLIT : MOVE ENTER :START REW FF SKIP / SEARCH CH SCAN SWAP POP CHREC LIGHT P I CTURE MODE P I CTURE SETT I NGS 1080 i 540p D I SPLAY FORMAT C I NEMA MODE CONVERGENCE RESET SAVE MODE P I CTURE F I LM P I CTURE SETT I NGS V I DEO D I SPLAY FORMAT C I NEMA MODE CONVERGENCE RESET SAVE : SELECT ENTER :SET noitcudortnIr g otniitncoeMnr nuooCyl orte nhtocg e nitsoUmerr op tiung oniMttr euSoyr uor yog tinintoarMepOxidneppAx ednI39 (E) 51HC85, 57HC85, 65HC85 Selecting the video input source Press INPUT on the remote control or the monitor front panel to view a signal from another device connected to your monitor, such as a VCR or DVD player (see illustrations below). You can select VIDEO 1, VIDEO 2, VIDEO 3, ColorStream HD1, ColorStream HD2 or HDMI depending on which input terminals are used for connecting the devices (see “Connecting your Monitor” on page 8). SOURCE 1 2 : : 3 4 : : HDM I Note: • When HDMI is selected the VIDEO OUT terminal does not output a signal. • When ColorStream HD 1 or HD 2 is selected, the VIDEO OUT terminal does not output a signal. To receive a VIDEO OUT signal, use a standard video or S- video IN connection instead of the SELECT ION SOURCESELECT ION ColorStream connection. • In POP double-window mode, the main 5 6 : : V V VColorStream ColorStream I I I DEO DEO DEO 1 2 3 HD1 HD2 HDM I window will display 480i signals only. If you select ColorStream HD1, ColorStream HD2, or HDMI while the POP picture is 1- 6 : TO SELECT I NPUT : TO SELECT active, the message “Not Available” will display. Labeling the video input sources The video label feature allows you to label each input source for your monitor from the following preset list of labels: – – – : Uses the default label name VCR : Video cassette recorder DVD : DVD video DTV : Digital TV set-top box SAT : Satellite box CBL : Cable box For example, if you have a DVD player connected to the monitor’s ColorStream HD1 inputs, you would label the ColorStream HD1 input source as “DVD.” Then, when you pressed INPUT, you would see the label “DVD” (instead of ColorStream HD1”) in the SOURCE SELECTION list. To label the video input sources: 1. Press MENU, and then press x or • until the CUSTOM menu appears. 2. Press y or z to highlight VIDEO LABEL. 1 2 3 4 5 6 3. Press ENTER to display the VIDEO LABEL menu. 7 8 94. Press y or z to highlight the video source you want to label and 100 0 ENT then press ENTER. 5. Press y or z to select the desired label for that input source. 6. Finish labeling the other video sources as desired. To return to the previous menu, press y or z to highlight CUSTOM MENU, and then press ENTER. 7. To exit the menu, press EXIT. V V VColorStream ColorStream I I I DEO DEO DEO 1 2 3 HD1 HD2 Pressing INPUT on the remote control displays the current signal source (press INPUT again or 1-6 to change) Pressing INPUT on the monitor changes the current signal source Number #01E_37-41_51HC85 40 05.4.28, 6:17 PM Black Note the following regarding the HDMI source selection: • Never connect this monitor to a personal computer (PC). This monitor is not intended for use with a PC. • See page 15 for details on connecting a device to the HDMI input. Monitor front panel VOLUME MENU EXIT INPUT INPUT CUSTOM SLEEP T I MER 0h00m CC OFF V I DEO LABEL INPUTRECALL POWER BACKGROUND SHADED INFO INPUT : MOVE ENTER:START +10 TOPMENU PIC SIZE MENU MENU yzx • V I DEO1 ENTER EXICT LEAR EXIT ENTER TVCBL/SAT VCR DVD DVDMENU V I DEO LABEL – – – V I DEO2 V I DEO3 VCR DVD C o l o r S t r e a m HD1 DTV SAT CBL ENTER C o l o r S t r e a m HD2 HDM I CUSTOM MENU : SELECT ENTER :SET noitcudortnIg niV tTcr eunonyoCl orte nhotCg e ntisoUmeRp uV Tg r niuttoeySr uor yog tinintoarMepOxidneppACH VOL x ednI40 (E) 51HC85, 57HC85, 65HC85 Using the closed caption feature The closed caption feature has two options: • Captions—An on-screen display of the dialogue, narration, and sound effects of TV programs and videos that are closed captioned (usually designated “CC” in program listings). • Text—An on-screen display of information not related to the current program, such as weather or stock data (when provided by individual stations). To view captions or text: 1. Tune the monitor to the desired program. 2. Press MENU, and then press x or • to display the CUSTOM menu. 3. Press y or z to highlight CC, and then press ENTER. CUSTOM SLEEP T I MER CAPT I ON TEXT INPUTRECALL POWER INFO1 2 3 4 5 6 7 8 9+10 100 0 ENT OFF CCV I DEO LABEL BACKGROUND TOP MENU PIC SIZE : SELECT ENTER :SET ENTER 4. Press y or z to highlight CAPTION or TEXT, and then press EXICT LEAR ENTER. STOP CUSTOM SLEEP T I MER C 1 CCC2V I DEO LABEL C3BACKGROUND C4: SELECT ENTER :SET • To view captions, highlight CAPTION in step 4 above, and then highlight C1, C2, C3, or C4 (C1 displays translation of the primary language in your area). Note: If the program or video you selected is not closed captioned, captions will not display on the screen. Giant pandas eat leaves. • To view text, highlight TEXT in step 4 above, and then highlight T1, T2, T3, or T4. Note: If text is not available in your area, a black rectangle may appear on your screen. If this happens, turn the Closed Caption feature OFF. WORLD WEATHER Temps Current F C Weather LONDON 51 11 MOSCOW PARIS ROME TOKYO MENU MENU DVDMENU yzx • ENTER ENTER TVCBL/SAT VCR DVD Note: A closed caption signal may not display in the following situations: • when a videotape has been dubbed • when the signal reception is weak • when the signal reception is nonstandard NOTICE OF POSSIBLE ADVERSE EFFECTS ON MONITOR PICTURE DISPLAY Avoid displaying stationary images on your monitor screen for extended periods of time. Fixed (non-moving) patterns or images (including but not limited to PIP/ POP windows, closed captions, video game patterns, TV station logos (from VCR, etc.), stock tickers, websites, and special formats that do not use the entire screen) can become permanently ingrained in the cathode ray tube(s) of the monitor and cause subtle but permanent ghost images. This type of damage is NOT COVERED BY YOUR WARRANTY. See item 33 on page 4 for details. CH VOL POP DIRECT CH MUTE SLEEP TV/VCR PAUSE PLAY FREEZE SOURCE SPLIT REW FF SKIP / SEARCH CH SCAN SWAP POP CHREC LIGHT This pull-down menu appears when CAPTION is selected. #01E_37-41_51HC85 41 05.4.28, 6:17 PM Black Clear 57 14 53 12 66 19 65 18 To turn off the Closed Caption feature: Highlight OFF in step 4. Cloudy Clear Cloudy Rain noitcudortnIr g otniitncoeMnr nuooCyl orte nhtocg e nitsoUmerr op tiung oniMttr euSoyr uor yog tinintoarMepOxidneppAx ednI41 (E) 51HC85, 57HC85, 65HC85 Setting the sleep timer To set the sleep timer to turn off the monitor automatically: 1. Press SLEEP to set the length of time until the monitor turns off. T I MER 0 h 00m Every time you press the SLEEP, the time display will increase by 10 minutes, up to 3 hours. 0h00m → 0h10m → 0h20m 2h50m → 3h00m → 0h00m To cancel the sleep timer: Press SLEEP until it is set to 0h00m. The sleep timer can also be set using the on-screen menus: 1. Press MENU, and then press x or • until the CUSTOM menu appears. 2. Press y or z to highlight SLEEP TIMER, and then press ENTER. 3. Press the Number buttons to enter the length of time until the monitor turns off automatically. 4. Press ENTER to start the timer. CUSTOM SLEEP T I MER CCV I DEO LABEL BACKGROUND Note : • When an instant power failure occurs, the sleep timer settings may be cleared. • To display the amount of time left until the monitor turns on or off automatically, press RECALL. INPUTRECALL POWER INFO+10 PIC SIZE EXIT ENTER MUTE SLEEP RECALL #01E_42-47_51HC85 42 05.4.28, 6:17 PM Black 1 2 3 4 5 6 7 8 9100 0 ENT Number TOPMENU MENU MENU DVDMENU yzx • ENTEENR TER CLEAR TVCBL/SAT CH VOL VCR DVD 2h00m SLEEP 0–9 : SELECT ENTER : SET Setting the clock To set the clock: 1. Press MENU, and then press x or • until the SET UP menu appears. 2. Press y or z to highlight CLOCK SET, and then press ENTER. 3. Press the Number buttons (0-9) to enter the correct time. The clock operates on a 24-hour cycle. (e.g. 1:00 p.m. equals 13:00, 5:00 p.m. equals 17:00.) 4. Press ENTER to start the clock. LANGUAGE noitcudortnIg niV tTcr eunonyoCl orte nhotCg e ntisoUmeRp uV Tg r niuttoeySr uor yog tinintoarMepNote : OIf the monitor’s power source is interrupted (the power cord is unplugged or a power failure occurs), the clock must be reset. xidneppASET UP CLOCK SET 0 9 : 2 5 0–9 : SELECT ENTER : SET x edTo display the time on-screen: nIPress RECALL. 42 (E) 51HC85, 57HC85, 65HC85 Adjusting the sound Muting the sound Press MUTE to temporarily reduce (1/2 MUTE) or turn off (MUTE) the sound. While the sound is off, the screen will display “1/2 MUTE” or “MUTE” in the lower right corner. Every time you press MUTE, the mute mode will change in the following order. → Normal → 1/2 MUTE → MUTE When you select “MUTE” mode, the closed caption feature is automatically activated. To deactivate this feature, deactivate MUTE. This feature works only when the closed caption mode is set to OFF. See “Using the closed caption feature” on page 41 for more information. Using the WOW® surround sound feature WOW® is a special combination of SRS Labs audio technologies that creates a thrilling surround sound experience with deep, rich bass from stereo sound sources. Your monitor’s audio will sound fuller, richer, and wider. To adjust the WOW feature: 1. Press MENU, and then press x or • until the AUDIO menu appears. 2. Press y or z to highlight the desired WOW feature you want to adjust, then press ENTER. • SRS 3D — To turn on or off the surround sound effect. • FOCUS — To turn on or off the vocal emphasis effect. • TruBass — To select your desired bass expansion level (HIGH, LOW, or OFF). AUDIO AUDIO SETTINGS WOW SRS 3D FOCUS TruBass INPUTRECALL POWER INFO1 2 3 4 5 6 7 8 9+10 100 0 ENT TOP MENU PIC SIZE MENU MENU ENTER DVDMENU yzx • ENTER EXICT LEAR MUTE SLEEP MUTE Monitor front panel VOLUME MENU EXIT INPUT x •zy ENTER MENU (ENTER) Note: If the broadcast is monaural, the WOW SRS 3D surround sound effect will not work. SRS WOW, SRS and symbol are trademarks of SRS Labs, Inc. SRS WOW technology is incorporated under license from SRS Labs, Inc. #01E_42-47_51HC85 43 05.4.28, 6:17 PM Black TVCBL/SAT VCR DVD CH VOL ON OFF : SELECT ENTER : SET 3. Press y or z to select the item, then press ENTER. noitcudortnIr g otniitncoeMnr nuooCyl orte nhtocg e nitsoUmerr op tiung oniMttr euSoyr uor yog tinintoarMepOxidneppAx ednI43 (E) 51HC85, 57HC85, 65HC85 Adjusting the sound quality You can change the quality of your monitor’s sound by adjusting the bass, treble, and balance. To adjust the sound quality: 1. Press MENU, and then press x or • until the AUDIO menu appears. 2. Press y or z to highlight AUDIO SETTINGS, and then press ENTER. The AUDIO SETTINGS menu appears. MOVE : : ADJUST POWER INPUTRECALL INFO1 2 3 4 5 6 7 8 9+10 100 0 ENT TOPMENU PIC SIZE MENU DVDMENU ENTER EXICT LEAR STOP AUD I O SETT I NGS BASS 7 0 TREBLE 5 0 BALANCERESET SAVE 3. Press y or z to highlight the item you want to adjust. 4. Press x or • to adjust the level. • x makes the sound quality weaker or increases the balance in the left channel, depending on the item selected. • • makes the sound quality stronger or increases the balance in the right channel, depending on the item selected. Resetting your audio adjustments The RESET function returns your audio adjustments to the following factory settings: Bass .................. center (50) Treble ............... center (50) Balance ............ center (0) To reset your audio adjustments: 1. Press MENU, and then press x or • until the AUDIO menu appears. 2. Press y or z to highlight AUDIO SETTINGS, and then press ENTER. The AUDIO SETTINGS menu appears. 3. Press y or z to highlight RESET, and then press ENTER. BASS ENTER 0 RESET AUD I O MENU TVCBL/SAT VCR DVD VOL CH POP DIRECT CH MUTE SLEEP TV/VCR PAUSE PLAY FREEZE SOURCE SPLIT REW FF SKIP / SEARCH CH SCAN SWAP POP CHREC LIGHT AUD I O SETT I NGS 5 0 TREBLE 5 0 BALANCERESET SAVE : MOVE : ADJUST #01E_42-47_51HC85 44 05.4.28, 6:17 PM Black noitcudortnIg niV tTcr eunonyoCl orte nhotCg e ntisoUmeRp uV Tg r niuttoeySr uor yog tinintoarMepOxidnep0 pRESET AUD I O MENU Ax ednI44 (E) 51HC85, 57HC85, 65HC85 MENU yzx • ENTER Using the StableSound® feature When the signal source is changed, the StableSound feature limits the highest volume level to prevent extreme changes in volume (for example, to prevent the sudden increase in volume that often happens when a TV program switches to a commercial). To turn on the StableSound feature: 1. Press MENU, and then press x or • until the AUDIO menu appears. 2. Press y or z to highlight STABLE SOUND, and then press ENTER. 3. Press y or z to select ON, and then press ENTER. : SELECT ENTER : SET INPUTRECALL POWER INFO +10 PIC SIZE EXIT TVCBL/SAT VCR DVD 1 2 3 4 5 6 7 8 9100 0 ENT TOPMENU ENTER CLEAR MENU ENTER Note: Make sure the volume control of your audio amplifier is set to a moderate listening level. #01E_42-47_51HC85 45 05.4.28, 6:17 PM Black MENU DVDMENU yzx • ENTER STABLE AUDIO SOUNDSPEAKERS ONOFF AUD I O OUT To turn off the StableSound feature: Select OFF in step 3 above. Turning off the built-in speakers Use this feature to turn off the monitor’s built-in speakers when you connect an audio system (See “Connecting an audio system” on page 17). To turn off the built-in speakers: 1. Press MENU, then press x or • until the AUDIO menu appears. 2. Press y or z to highlight SPEAKERS, and then press ENTER. 3. Press y or z to select OFF, and then press ENTER. : SELECT ENTER : SET CH VOL STABLE AUDIO SOUNDSPEAKERS ONOFF AUD I O OUT To turn on the built-in speakers: Select ON in step 3 above. noitcudortnIr g otniitncoeMnr nuooCyl orte nhtocg e nitsoUmerr op tiung oniMttr euSoyr uor yog tinintoarMepOxidneppAx ednI45 (E) 51HC85, 57HC85, 65HC85 Selecting noithe Audio OUT sound tcuThis feature allows you to select the sound source (MAIN or POP) dothat is output from the Audio OUT terminals (for example, see rt“Connecting two VCRs” on page 14). nIThis is useful when amplifying or recording the POP sound with external equipment (connected to the monitor’s Audio OUT terminals) while listening to the sound of the main picture through the monitor’s built-in speakers. g To select the Audio OUT sound: niV tTc1. Press MENU, and then press x or • until the AUDIO menu r euappears. nonyo2. Press y or z to highlight AUDIO OUT, and then press yzx • CENTER. 3. Press y or z to select MAIN or POP, and then press ENTER. ENTER l orte nhAUDIO otSTABLE SOUNDMA I N CSPEAKERS POP g AUD I O OUT e nNote: tiso• When the POP window is closed, the sound Umof the main program is output through the e: SELECT ENTER : SET RAUDIO OUT terminals, even if POP is • MAIN: Outputs the sound of the main (left window) program to the Audio OUT terminals. • POP : Outputs the sound of the POP (right window) program selected in the AUDIO OUT menu. • The sound of the main program is always output through the monitor's built-in p speakers, regardless of the AUDIO OUT uto the Audio OUT terminals. V setting. Tg r niutSelecting the background of the menu display toeySYou can change the background of the menu display by selecting from two preset backgrounds: shaded and solid (gray). To select the background: r 1. Press MENU, and then press x or • until the CUSTOM menu uappears. or yo2. Press y or z to highlight BACKGROUND, and then press g tininENTER. toar3. Press y or z to select either a SHADED or SOLID background, Mepand then press ENTER. OCUSTOM SLEEP T I MER SHADED CCSOL I D xiV I DEO LABEL BACKGROUND dnepp: SELECT ENTER : SET Ax ednI46 #01E_42-47_51HC85 46 05.4.28, 6:17 PM Black (E) 51HC85, 57HC85, 65HC85 INPUTRECALL POWER INFO1 2 3 4 5 6 7 8 9+10 100 0 ENT TOPMENU PIC SIZE MENU ENTER EXICT LEAR STOP MENU DVDMENU ENTER TVCBL/SAT VCR DVD CH VOL POP DIRECT CH MUTE SLEEP TV/VCR PAUSE PLAY FREEZE SOURCE SPLIT REW FF SKIP / SEARCH CH SCAN SWAP POP CHREC LIGHT Displaying monitor status information on- screen Press RECALL to display the following information on-screen: • Input mode • Time (if set) • Remaining time on SLEEP timer (if set) • Video label (when in VIDEO mode) • V-CHIP rating status • Picture size 123456789101112131415161718 INPUTRECALL POWER +10 PIC SIZE EXIT RECALL ENTER #01E_42-47_51HC85 47 05.4.28, 6:17 PM Black INFO TVCBL/SAT VCR DVD 1 2 3 4 5 6 7 8 9100 0 ENT TOP MENU 33 34 35 ENTER CLEAR HD1 33 34 35 MENU D L S V DVDMENU SLEEP T I MER 1h23m CLOCK 12 : 3 4 ColorStream Understanding the last mode memory feature If the power is cut off while you are viewing the monitor, the Last Mode Memory feature turns on the monitor automatically when the power is resupplied. If the power is going to be off for a long time and you are going to be away from your monitor, unplug the power cord to prevent the monitor from turning on in your absence. ENTER CH VOL THEATERWIDE 1 DVD noitcudortnIr g otniitncoeMnr nuooCyl orte nhtocg e nitsoUmerr op tiung oniMttr euSoyr uor yog tinintoarMepOxidneppAx ednI47 (E) 51HC85, 57HC85, 65HC85 Appendix Specifications • This model complies with the specifications listed below. • Design and specifications are subject to change without notice. • This model may not be compatible with features and/or specifications that may be added in the future. WARNING: RISK OF ELECTRIC SHOCK! Never attempt to service the monitor yourself. Opening and removing the covers may expose you to dangerous voltage or other hazards. Refer all servicing to a Toshiba Authorized Service Center. Power Source 120 V AC, 60 Hz Video/Audio Terminals (continued) VARIABLE AUDIO OUTPUT Power Consumption 0–300 mV(rms) (30% modulation equivalent, 185 W (average) 2.2 k ohms or less) 0.7 W (in standby mode) HDMI INPUT Audio Power HDMI compliant (type A connector) HDCP compliant 15 W + 15 W E-EDID compliant Speaker Type Suggested scan rates: 1080i, 480p, 480i, 720p HDMI Audio 2-channel PCM; 32/44.1/48 kHz Two 6-5/16 inches (16 cm) round sampling frequency; 16/20/24 bits per sample Video/Audio Terminals S-VIDEO INPUT Y : 1 V(p-p), 75 ohms, negative sync. Dimensions 51HC85: C : 0.286 V(p-p) (burst signal), 75 ohms VIDEO/AUDIO INPUT VIDEO: 1 V(p-p), 75 ohms, negative sync. 57HC85: AUDIO: 150 mV(rms) (30% modulation equivalent, 22 k ohms or more) Width 47-3/5 inches (1,209 mm) Height 50-5/8 inches (1,280 mm) Depth 22-4/9 inches (570 mm) Width 52-3/4 inches (1,340 mm) Height 55-1/16 inches (1,399 mm) Depth 23-7/8 inches (606 mm) ColorStream® (component video) INPUT Y : 1V(p-p), 75 ohms PR: 0.7 V(p-p), 75 ohms 65HC85: Width 59-7/8 inches (1,521mm) Height 59-7/8 inches (1,521mm) Depth 26-1/4 inches (665 mm) PB: 0.7 V(p-p), 75 ohms AUDIO: 150 mV(rms), 22 k ohms or more VIDEO/AUDIO OUTPUT VIDEO: 1 V(p-p), 75 ohms, negative sync. noitcudortnIg niV tTcr eunonyoCl orte nhotCg e ntisoUmeRp uV Tg r niuttoeySs ’Vs Tere Mass uhtt51HC85: 169 lbs (76.8 kg) ag en57HC85: 230 lbs (105 kg) FisAUDIO: 150 mV(rms) (30% modulation equivalent, 65HC85: 240 lbs (108 kg) U2.2 k ohms or less) Supplied Accessories • Two dual-wand IR blaster cable • Remote Control with 2 size “AA” alkaline batteries xidneppAx ednI___ *E-EDID = Enhanced-Extended Display Identification 48 #01E_48-50_51HC85 48 05.4.28, 6:17 PM Black (E) 51HC85, 57HC85, 65HC85 Troubleshooting Before calling a service technician, please check the following table for a possible cause of the symptom and some solutions. Symptom Solution Monitor will not turn on • Make sure the power cord is plugged in, then press POWER. • The remote control batteries may be dead. Replace the batteries. No picture, no sound • If you connected an antenna via an external device (such as a VCR), check the antenna/cable connections. No sound, picture OK • The sound may be muted. Press VOLUME. • properly. Make sure the SPEAKERS function in the AUDIO menu is set Poor picture, sound OK • If you connected an antenna via an external device (such as a VCR), check the antenna/cable connections. • Adjust the PICTURE menu. Black box appears on the screen • The closed caption feature may be set to one of the Text modes (T1, T2, T3, or T4). Turn closed captioning OFF. Poor color or no color • menu. Adjust the TINT and/or COLOR in the PICTURE SETTINGS The remote control does not operate • Make sure the appropriate device mode is selected. • Remove all obstructions between the remote control and the remote control sensor in the monitor. • The remote control batteries may be dead. Replace the batteries. #01E_48-50_51HC85 49 05.4.28, 6:17 PM Black noitcudortnIr g otniitncoeMnr nuooCyl orte nhtocg e nitsoUmerr op tiung oniMttr euSoyr uor yog tinintoarMepOxidneppAx ednI49 (E) 51HC85, 57HC85, 65HC85 Limited United States Warranty for 51HC85, 57HC85, 65HC85 Toshiba America Consumer Products, L.L.C. (“TACP”) makes the following limited warranties to original consumers in the United States. THESE LIMITED WARRANTIES EXTEND TO THE ORIGINAL CONSUMER PURCHASER OR ANY PERSON RECEIVING THIS MONITOR AS A GIFT FROM THE ORIGINAL CONSUMER PURCHASER AND TO NO OTHER PURCHASER OR TRANSFEREE. MONITORS PURCHASED IN THE U.S.A. AND USED ANYWHERE OUTSIDE OF THE U.S.A., INCLUDING, WITHOUT LIMITATION, CANADA AND MEXICO, ARE NOT COVERED BY THESE WARRANTIES. MONITORS PURCHASED ANYWHERE OUTSIDE OF THE U.S.A., INCLUDING, WITHOUT LIMITATION, CANADA AND MEXICO, AND USED IN THE U.S.A., ARE NOT COVERED BY THESE WARRANTIES. Limited One (1) Year Warranty on Parts and Labor TACP warrants this monitor and its parts against defects in materials or workmanship for a period of one (1) year after the date of original retail purchase. DURING THIS PERIOD, TACP WILL, AT TACP’S OPTION, REPAIR OR REPLACE A DEFECTIVE PART WITH A NEW OR REFURBISHED PART WITHOUT CHARGE TO YOU FOR PARTS OR LABOR. During this period, TACP Authorized Service Station personnel will come to your home when warranty service is required. Depending on the type of repair required, the service will either be performed in your home or the monitor will be taken to a TACP Authorized Service Station for repair and returned to your home at no cost to you. Limited Two (2) Year Warranty on Picture Tube TACP warrants the picture tube in this monitor against defects in materials or workmanship for a period of two (2) years after the date of original retail purchase. DURING THIS PERIOD, TACP WILL, AT TACP’S OPTION, REPAIR OR REPLACE A DEFECTIVE PICTURE TUBE WITH A NEW OR REFURBISHED PICTURE TUBE WITHOUT CHARGE TO YOU, PROVIDED THAT IF A DEFECTIVE PICTURE TUBE IS REPAIRED OR REPLACED AFTER ONE (1) YEAR AFTER THE DATE OF ORIGINAL RETAIL PURCHASE, YOU MUST PAY FOR ALL LABOR CHARGES IN CONNECTION WITH THE REPAIR OR REPLACEMENT THEREOF. During this period, TACP Authorized Service Station personnel will come to your home when warranty service is required. Depending on the type of repair required, the service will either be performed in your home or the monitor will be taken to a TACP Authorized Service Station for repair and returned to your home at no cost to you. Rental Units The warranty for monitor rental units begins on the date of the first rental or thirty (30) days after the date of shipment to the rental firm, whichever comes first. Limited Warranty for Commercial Units TACP warrants monitors that are sold and used for commercial purposes as follows: all parts are warranted against defects in materials or workmanship for a period of ninety (90) days after the date of original retail purchase. DURING THIS PERIOD, TACP WILL, AT TACP’S OPTION, REPAIR OR REPLACE A DEFECTIVE PART WITH A NEW OR REFURBISHED PART WITHOUT CHARGE TO YOU. Owner’s Manual and Product Registration Card Read this owner’s manual thoroughly before operating this monitor. Complete and mail the enclosed product registration card or register your monitor online at www.tacp.toshiba.com/ service as soon as possible. By registering your monitor you will enable TACP to bring you new products specifically designed to meet your needs and help us to contact you in the unlikely event a safety notification is required under the U.S. Consumer Product Safety Act. Failure to complete and return the product registration card does not diminish your warranty rights. 0305 #01E_48-50_51HC85 50 05.4.28, 6:17 PM Black noitcudortnYour Responsibility ITHE ABOVE WARRANTIES ARE SUBJECT TO THE FOLLOWING CONDITIONS: (1) You must retain your original bill of sale or provide other proof of purchase. (2) All warranty servicing of this monitor must be performed by g an Authorized TACP Service Station. niV t(3) The warranties from TACP are effective only if this monitor is Tcr epurchased and operated in the Continental U.S.A. or Puerto Rico. un(4) Labor service charges for set installation, setup, adjustment onyoof customer controls, and installation or repair of antenna Csystems are not covered by this warranty. Reception problems caused by inadequate antenna systems, misaligned satellite dishes, cable television distribution, VCRs, DVD players/recorders, personal computer level IEEE1394 devices, and any other connected signal source l device are your responsibility. ort(5) Warranties extend only to defects in materials or workmanship e nas limited above, and do not extend to any monitor or parts hotthat have been lost or discarded by you or to damage to the Cg monitor or parts caused by fires, misuse, accident, Acts of God e nti(such as lightning or fluctuations in electric power), improper soinstallation, improper maintenance, or use in violation of Uminstructions furnished by TACP; use or malfunction through esimultaneous use of this monitor and connected equipment; or Rto units that have been modified or had the serial number removed, altered, defaced, or rendered illegible. How to Obtain Warranty Service If, after following all of the operating instructions in this manual p and reviewing the section entitled “Troubleshooting,” you find uV that service is needed: Tg r (1) To find the nearest TACP Authorized Service Station, visit TACP’s niutwebsite at www.tacp.toshiba.com/service or contact toeTACP’s Consumer Solution Center toll free at 1-800-631-3811. yS(2) You must present your original bill of sale (or a copy thereof) or other proof of purchase to the TACP Authorized Service Station. For additional information, visit TACP’s website: www.tacp.toshiba.com s ALL WARRANTIES IMPLIED BY THE LAW OF ANY STATE OF ’THE U.S.A., INCLUDING THE IMPLIED WARRANTIES OF Vs TMERCHANTABILITY AND FITNESS FOR A PARTICULAR ere PURPOSE, ARE EXPRESSLY LIMITED TO THE DURATION OF uhttTHE LIMITED WARRANTIES SET FORTH ABOVE. WITH THE aEXCEPTION OF ANY WARRANTIES IMPLIED BY THE LAW OF g enANY STATE OF THE U.S.A. AS HEREBY LIMITED, THE FisFOREGOING WARRANTY IS EXCLUSIVE AND IN LIEU OF UALL OTHER WARRANTIES, GUARANTEES, AGREEMENTS, AND SIMILAR OBLIGATIONS OF TACP WITH RESPECT TO THE REPAIR OR REPLACEMENT OF ANY PARTS. IN NO EVENT SHALL TACP BE LIABLE FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, LOST PROFITS, BUSINESS INTERRUPTION, OR xiMODIFICATION OR ERASURE OF RECORDED DATA CAUSED dBY USE, MISUSE OR INABILITY TO USE THIS MONITOR). neNo person, agent, distributor, dealer, or company is authorized to pchange, modify, or extend the terms of these warranties in any pmanner whatsoever. The time within which an action must be Acommenced to enforce any obligation of TACP arising under the warranty or under any statute or law of the United States or any state thereof is hereby limited to ninety (90) days from the date you discover, or should have discovered, the defect. This limitation does not apply to implied warranties arising under the law of any state of the U.S.A. THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH MAY VARY x eFROM STATE TO STATE IN THE U.S.A. SOME STATES OF THE dU.S.A. DO NOT ALLOW LIMITATIONS ON THE DURATION OF nIAN IMPLIED WARRANTY, WHEN AN ACTION MAY BE BROUGHT, OR THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES. THEREFORE, THE ABOVE PROVISIONS MAY NOT APPLY TO YOU UNDER SUCH CIRCUMSTANCES. 50 Index AA/V cables (standard) ......................................................... 8 Audio OUT sound, selecting ...........................................46 Audio system connection ................................................. 17 Auto aspect........................................................................... 30 BBACKGROUND selection ................................................46 Back of the monitor .............................................................. 7 CCableClear® DNR ................................................................38 Cable converter box connection ...................................10 Camcorder connection ...................................................... 14 Cinema mode ........................................................................39 Clock, setting ........................................................................42 Closed caption ......................................................................41 Color convergence .............................................................. 25 Color temperature ...............................................................38 ColorStream® (component video) cables .................... 8 Convergence adjustment .................................................25 DDisplay format...................................................................... 39 Double-window (“POP”) feature ...................................31 DTV receiver connection ..................................................13 DVD connection........................................................... 11, 12 F H I Front of the monitor ............................................................. 7 HDMITM connection ............................................................15 INPUT button ........................................................................40 L M N Labeling video input source........................................... 40 Language selection ............................................................25 Last mode memory ............................................................. 47 Locks menu ...........................................................................33 Menu system ......................................................................... 24 MUTE button ......................................................................... 43 Number buttons ................................................................... 19 PPicture adjustments COLOR TEMPERATURE ..............................................38 Picture mode ....................................................................36 Picture quality .................................................................. 37 Picture-out-picture (POP) SOURCE button ............................................................. 31 SPLIT button .................................................................... 31 SWAP button ....................................................................32 Picture scroll .......................................................................... 29 Picture size selection ......................................................... 27 POP Window..........................................................................31 Power button .........................................................................24 Q R RECALL button .................................................................... 47 Remote control Battery installation .........................................................18 Effective range ................................................................. 18 Learning about the buttons ........................................19 Programming....................................................................22 RESET .............................................................................. 39, 44 SSatellite receiver connection...........................................11 Scrolling the TheaterWide® picture..............................29 Set-top box ............................................................................13 Sleep timer .............................................................................42 Sound quality adjustments ..............................................44 SPEAKERS on/off ...............................................................45 Specifications........................................................................48 SRS 3D surround.................................................................43 StableSound® ........................................................................45 S-video cables ........................................................................ 8 TTheaterWide® picture.........................................................28 Troubleshooting .................................................................. 49 VV-CHIP BLOCKING OPTION ......................................................35 ENABLE BLOCKING .................................................... 34 MPAA RATING ................................................................35 NEW PIN CODE ............................................................. 36 TV RATING ........................................................................34 VCR connection ..................................................................... 9 VIDEO LABEL ...................................................................... 40 WWarranty ................................................................................. 50 WOW® surround sound feature.....................................43 #01E_51_51HC85 51 05.4.28, 6:17 PM Black noitcudortnIr g otniitncoeMnr nuooCyl orte nhtocg e nitsoUmerr op tiung oniMttr euSoyr uor yog tinintoarMepOxidneppAx ednI51 (E) 51HC85, 57HC85, 65HC85 PRINTED IN USA #01E_52_51HC85 52 05.4.28, 6:17 PM Black (05-05) YC/N 23566643 (E) 51HC85, 57HC85, 65HC85 HEAD OFFICE: 82 TOTOWA ROAD, WAYNE, NEW JERSEY 07470, U.S.A. NATIONAL SERVICE DIVISON: 1420B TOSHIBA DRIVE, LEBANON, TN. 37087, U.S.A. MANUFACTURED BY CableClear, ColorStream, StableSound, and TheaterWide are registered trademarks of Toshiba America Consumer Products, L.L.C.

FREE ENGLISH PDF

OPERATING INSTRUCTIONS

USER GUIDE - USER MANUAL

OWNER GUIDE - OWNER MANUAL

REFERENCE GUIDE - REFERENCE MANUAL

INSTRUCTION GUIDE - INSTRUCTION MANUAL