WINDSOR CLIPPER DUO CLPDU 1.008-048.0 (01) PDF MANUAL

Report any errors on this page in the comment box below.

PDF OCR Transcript: Clipper Duo Carpet Extractor Operating Instructions (ENG) MODEL: 1.008-048.0 CLPDU From Serial Number (Ref No1) See Serial Number Page in Spare Parts List or call manufacturer 86408790-A 10/29/15 2 Machine Data Label Overview 86408790 Operator’s Manual - Clipper Duo This carpet extractor is an electrical powered, portable carpet extractor intended for commercial use. The appliance sprays a cleaning solution onto the carpet, agitates the wet carpet, and then extracts the soiled solution back into the unit's recovery tank. The appliance is fitted with and a hand tool for cleaning upholstery and stairs. Warranty Registration Thank you for purchasing a Kärcher North America product. Warranty registration is quick and easy. Your registration will allow us to serve you better over the lifetime of the product. To register your product go to : http://warranty.karcherna.com/ For customer assistance: 1-800-444-7654 Table of Contents Machine Data Label. . . . . . . . . . . . . . . . . . . . . . . . . .2 Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . .3 How To Use This Manual . . . . . . . . . . . . . . . . . . . . .4 Safety IMPORTANT SAFETY INSTRUCTIONS . . . . . . . . .5 CONSIGNES DE SÉCURITÉ IMPORTANTES . . . .6 HAZARD INTENSITY LEVEL . . . . . . . . . . . . . . . . . .7 NIVEAU D'INTENSITÉ DU DANGER. . . . . . . . . . . .8 Safety Labels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9 Grounding Instructions . . . . . . . . . . . . . . . . . . . . . .10 Instructions De Mise À La Terre . . . . . . . . . . . . . . .11 Operations Technical Specifications . . . . . . . . . . . . . . . . . . . . .12 How this machine works . . . . . . . . . . . . . . . . . . . . .14 Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15 Controls. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16 Filling The Solution Tank . . . . . . . . . . . . . . . . . . . .17 Pre Run Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . .18 Operating The Machine . . . . . . . . . . . . . . . . . . . . .20 Using The Hand Tool . . . . . . . . . . . . . . . . . . . . . . .23 Maintenance Service Schedule . . . . . . . . . . . . . . . . . . . . . . . . . .24 Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25 Periodic Maintenance . . . . . . . . . . . . . . . . . . . . . . .26 Circuit Protection. . . . . . . . . . . . . . . . . . . . . . . . . . .27 Scrub Deck . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28 Scrub Head. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29 Scrub Brush Replacement . . . . . . . . . . . . . . . . . . .29 Vacuum Motor Carbon Brushes . . . . . . . . . . . . . . .30 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . .31 Suggested Spare Parts. . . . . . . . . . . . . . . . . . . . . .32 86408790 Operator’s Manual - Clipper Duo 3 4 How To Use This Manual This manual contains the following sections: • How to Use This Manual • Safety • Operations • Maintenance The HOW TO USE THIS MANUAL section will tell you how to find important information for ordering correct repair parts. Parts may be ordered from authorized dealers. When placing an order for parts, the machine model and machine serial number are important. Refer to the MACHINE DATA box which is filled out during the installation of your machine. The MACHINE DATA box is located on the inside of the front cover of this manual. The model and serial number of your machine is located on the back of the machine. The SAFETY section contains important information regarding hazardous or unsafe practices of the machine. Levels of hazards are identified that could result in product damage, personal injury, or severe injury resulting in death. The OPERATIONS section is to familiarize the operator with the operation and function of the machine. The MAINTENANCE section contains preventive maintenance information to keep the machine and its components in good working condition. They are listed in this general order: • Periodic Maintenance • Daily/Regular Maintenance • Troubleshooting Model: Date of Purchase: Serial Number: Dealer: NOTE: If a service or option kit is installed on your machine, be sure to keep the KIT INSTRUCTIONS which came with the kit. It contains replacement parts numbers needed for ordering future parts. Address: NOTE: The manual part number is located on the Phone Number: lower right corner of the front cover. Sales Representative: 86408790 Operator’s Manual - Clipper Duo Safety IMPORTANT SAFETY INSTRUCTIONS When using this machine, basic precaution must always be followed, including the following: READ ALL INSTRUCTIONS BEFORE USING THIS MACHINE. To reduce the risk of fire, electric shock, or injury: Connect to a properly grounded outlet. See Grounding Instructions. Do not leave the machine unattended. Unplug machine from outlet when not in use and before maintenance or service. Use only indoors. Do not use outdoors or expose to rain. Do not allow machine to be used as a toy. Close attention is necessary when used by or near children. Use only as described in this manual. Use only manufacturer's recommended components and attachments. Do not use damaged electrical cord or plug. Follow all instructions in this manual concerning grounding the machine. If the machine is not working properly, has been dropped, damaged, left outdoors, or dropped into water, return it to an authorized service center. Do not pull or carry machine by electrical cord, use as a handle, close a door on cord, or pull cord around sharp edges or corners. Do not run machine over cord. Keep cord away from heated surfaces. Do not unplug machine by pulling on cord. To unplug, grasp the electrical plug, not the electrical cord. Do not handle the electrical plug or machine with wet hands. Do not operate the machine with any openings blocked. Keep openings free of debris that may reduce airflow. This machine is intended for cleaning carpet only. Do not vacuum anything that is burning or smoking, such as cigarettes, matches, or hot ashes. This machine is not suitable for picking up health endangering dust. Turn off all controls before unplugging. Machine can cause a fire when operating near flammable vapors or materials. Do not operate this machine near flammable fluids, dust or vapors. This machine is suitable for commercial use, for example in hotels, schools, hospitals, factories, shops and offices for more than normal housekeeping purposes. Maintenance and repairs must be done by qualified personnel. If foam or liquid comes out of machine, switch off immediately. READ AND SAVE THESE INSTRUCTIONS 86408790 Operator’s Manual - Clipper Duo 5 6 Safety 86408790 Operator’s Manual - Clipper Duo CONSIGNES DE SÉCURITÉ IMPORTANTES Lors de l'utilisation de cette machine, des précautions de base doivent toujours être prises, y compris les précautions suivantes : LIRE TOUTES LES INSTRUCTIONS AVANT D'UTILISER CETTE MACHINE. Pour réduire le risque d'incendie, d'électrocution ou de blessure : Cet appareil ne doit être connecter qu a des prises ayant une sortie de terre. Ne pas laisser l'appareil sans surveillance lorsqu'il est branché. Débrancher lorsque l'appareil n'est pas utilisé et avant l'entretien. Pour reduire les risques de choc electrique, ne pas utiliser à l exterieur et ne pas aspirer de matières humides. Ne pas permettre aux enfants de jouer avec l'appareil. Une attention particulière est nécessaire lorsque l'appareil est utilisé par des enfants ou à proximité de ces derniers. N'utiliser que conformément à cette notice avec les accessoires recommandés par le fabricant. Ne pas utiliser si le cordon ou la fiche est endommagé. Retourner l'appareil à un atelier de réparation s'il ne fonctionne pas bien, s'il est tombé ou s'il a été endommagé, oublié à l'extérieur ou immergé. Ne pas tirer soulever ou traîner l'appareil par le cordon. Ne pas utiliser le cordon comme une poignée, le coincer dans l'embrasure d'unée porte ou l'appuyer contre des arêtes vives ou des coins. Ne pas faire rouler l'appareil sur le cordon. Garder le cordon à l'écart des surfaces chaudes. Ne pas débrancher en tirant sur le cordon. Tirer plutôt la fiche. Ne pas toucher la fiche ou l'appareil lorsque vos mains sont humides. N'insérer aucun objet dans les ouvertures. Ne pas utiliser l'appareil lorsqu'une ouverture est bloquée. S'assure que de la poussière, de la peluche, des cheveux ou d'autres matières ne réduisent pas le débit d'air. Cette machine est destinée pour nettoyer tapis seulement. Ne pas aspirer de matiéres en combustion ou qui dégagent de la fumée, comme des cigarettes, des allumettes ou des cendres chaudes. Cette machine n'est pas adaptée au ramassage de poussières dangereuses. Mettre toutes les commandes à la position ARRÊT avant de débrancher l'appareil. Ne pas aspirer des liquides inflammables ou combustibles, comme de l'essence, et ne pas faire fonctionner dans des endroits où peuvent se trouver de tels liquides. Cette machine est destinée à un usage commercial. Elle est recommandée davantage pour les domaines hôtelier, scolaire, hospitalier, industriel ou pour les bureaux, les chaînes de magasin, que pour un usage domestique normal. L'entretien et les réparations de la machine doivent être effectuées par un personnel qualifié. Si de la mousse ou du liquide sort de la machine, la mettre hors tension immédiatement. LIRE ET CONSERVER CES INSTRUCTIONS Safety The following symbols are used throughout this guide as indicated in their descriptions: HAZARD INTENSITY LEVEL There are three levels of hazard intensity identified by signal words -WARNING and CAUTION and FOR SAFETY. The level of hazard intensity is determined by the following definitions: WARNING - Hazards or unsafe practices which COULD result in severe personal injury or death. CAUTION - Hazards or unsafe practices which could result in minor personal injury or product or property damage. FOR SAFETY: To Identify actions which must be followed for safe operation of equipment. Report machine damage or faulty operation immediately. Do not use the machine if it is not in proper operating condition. Following is information that signals some potentially dangerous conditions to the operator or the equip- ment. Read this information carefully. Know when these conditions can exist. Locate all safety devices on the machine. Please take the necessary steps to train the machine operating personnel. FOR SAFETY: DO NOT OPERATE MACHINE: Unless Trained and Authorized. Unless Operation Guide is Read and understood. In Flammable or Explosive areas. In areas with possible falling objects WHEN SERVICING MACHINE: Avoid moving parts. Do not wear loose clothing; jackets, shirts, or sleeves when working on the machine. Use manufacturer approved replacement parts. 86408790 Operator’s Manual - Clipper Duo 7 8 Safety 86408790 Operator’s Manual - Clipper Duo Les symboles suivants sont utilisés dans tout ce manuel, tels que décrits ici : NIVEAU D'INTENSITÉ DU DANGER Il existe trois niveaux d'intensité du danger, identifiés par des termes d'avertissement - AVERTISSEMENT, ATTENTION et POUR VOTRE SÉCURITÉ. Le niveau d'intensité du danger est déterminé par les définitions suivantes : AVERTISSEMENT - Les dangers ou des pratiques contraires à la sécurité qui POURRAIENT entraîner des blessures personnelles ou la mort. ATTENTION - Les dangers ou des pratiques contraires à la sécurité qui pourraient entraîner des blessures person- nelles légères ou des dégâts sur le produit ou d'autres biens. POUR DES RAISONS DE SÉCURITÉ : Pour identifier les actions qui doivent être exécutées pour un fonc- tionnement sûr de l'équipement. Signaler immédiatement tout dommage subi par la machine ou fonctionnement défectueux. Ne pas utiliser la machine si elle ne fonctionne pas correctement. Ci-dessous se trouvent les informations indiquant les conditions potentiellement dangereuses pour l'opérateur ou l'équipement. Lire attentivement ces informations. Être conscient que ces conditions peuvent survenir. Repérer tous les dispositifs de sécurité sur la machine. Suivre les étapes nécessaires de formation du personnel qui utilise la machine. POUR DES RAISONS DE SÉCURITÉ : NE PAS FAIRE FONCTIONNER LA MACHINE : Sauf si le personnel est formé et autorisé. Sauf si le manuel d'utilisation est lu et compris. Dans des zones inflammables ou explosives. Dans des zones contenant des objets susceptibles de tomber LORS DE L'ENTRETIEN DE LA MACHINE : Éviter les pièces mobiles. Ne pas porter de vêtements, vestes, chemises ou manches vagues lors de l'entretien de la machine. Utiliser les pièces de rechange approuvées par le fabricant. Safety Safety Labels NOTE: These drawings indicate the location of safety labels on the machine. If at any time the labels become illegible, promptly replace them. Emplacement De L'étiquette De Sécurité Les ÉTIQUETTES D'AVERTISSEMENT suivantes se trouvent sur votre unité de nettoyage. Ces étiquettes signalent les avertissements et mises en garde importantes qui doivent être suivis en tout temps. Le non respect des avertissements et mises en garde pourrait entraîner des dommages matériels, des blessures graves ou même la mort. Suivez attentivement ces instructions ! NE PAS retirer ces étiquettes. REMARQUE : Ces dessins indiquent l'emplacement des étiquettes de sécurité sur la machine. Si, à tout moment, les étiquettes deviennent illisibles, remplacez-les rapidement. WARNING LABEL 86242230 WARNING LABEL EXPLOSION FRENCH 86310500 86408790 Operator’s Manual - Clipper Duo 9 10 Safety Grounding Instructions Electrical In the USA this machine operates on a standard 15 amp 115 volt A.C. power circuit. The amp, hertz, and voltage are listed on the data label found on each machine. Using voltages above or below those indicated on the data label will cause serious damage to the motors Extension Cords If an extension cord is used, the wire size must be at least one size larger than the power cord on the machine, and must be limited to 50 feet (15.5m) in length. Grounding Instructions This appliance must be grounded. If it should malfunc- tion or breakdown, grounding provides a path of least resistance for electric current to reduce the risk of electric shock. This appliance is equipped with a cord having an equipment-grounding conductor and grounding plug. The plug must be inserted into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordi- nances. This appliance is for use on a nominal 120-volt circuit, and has a grounded plug that looks like the plug illus- trated in sketch A. A temporary adapter looks like adapter illustrated in sketches B and C, may be used to connect this plug to a 2-pole receptacle as shown in sketch B if a properly grounded outlet is not available. The temporary adapter should be used only until a properly grounded outlet (sketch A) can be installed by a qualified electrician. The green colored rigid ear, lug or the like extending from the adapter must be connected to a permanent ground such as a properly grounded outlet box cover. Whenever the adapter is used, it must be held in place by a metal screw Improper connection of the equipment-grounding conductor can result in a risk of electric shock. Check with a qualified electrician or service person if you are in doubt as to whether the outlet is properly grounded. Do not modify the plug provided with the appliance - if it will not fit the outlet, have a proper outlet installed by a qualified electrician. . Grounding Pin GROUNDING USING AN ADAPTOR CONNECTION Grounded Outlet Note: Adaptors are not allowed in Canada. NOTE: In Canada, the use of a temporary adapter is not permitted by the Canadian Electrical Code. 86408790 Operator’s Manual - Clipper Duo Grounded Outlet Box FIGURE A Adaptor Tab Screw for Grounding FIGURE C Adaptor Metal Screw FIGURE B Safety Instructions De Mise À La Terre Cet appareil doit être relié à la terre. S'il fonctionne mal ou tombe en panne, la mise à la terre fournit un chemin de résistance moindre au courant électrique pour réduire le risque d'électrocution. Cet appareil est fourni avec un cordon équipé d'un conducteur de mise à la terre d'équipement et d'une fiche de terre. La fiche doit être insérée dans une prise appropriée qui est correcte- ment installée et mise à la terre, conformément aux codes et réglementations locales. Une connexion incorrecte du conducteur de mise à la terre de l'équipement peut entraîner une électro- cution. En cas de doute sur la mise à la terre de la prise murale, vérifier, avec un électricien qualifié ou un technicien d'entretien. Ne pas modifier la fiche fournie avec l'appareil- Si elle ne correspond pas à la prise murale, faire installer une prise appropriée par un électricien qualifié. Cet appareil doit être utilisé sur un circuit nominal de 120 volts et est équipé d'une prise de terre qui ressemble à celle illustrée dans le schéma A. Un adap- tateur temporaire ressemble à l'adaptateur illustré aux schémas B et C, peut être utilisé pour brancher la fiche à une prise à 2 pôles comme illustrés au schéma B si aucune prise correctement reliée à la terre n'est dispo- nible. L'adaptateur temporaire doit être utilisé unique- ment jusqu'à ce qu'une prise correctement reliée à la terre (schéma A) puisse être installée par un électricien qualifié. La patte rigide ou le crochet de couleur verte ou l'équivalent à l'extrémité de l'adaptateur doit être connecté à une prise de terre permanente telle qu'une boîte de jonction correctement reliée à la terre. Dès lors que l'adaptateur est utilisé, il doit être maintenu en place par une vis métallique. Rallonges Si une rallonge est utilisée, la taille du fil doit être au moins une taille plus grande que le cordon d'alimenta- tion sur la machine, et doit être limitée à 50 pieds (15,5 millions) de longueur. REMARQUE : Au Canada, l'utilisation d'un adaptateur temporaire n'est pas autorisée par le code canadien de l'électricité. Fiche De Mise à La Terre Mise À La Terre En Utilisant Un Adaptateur Prise Reliée À La Terre Vis Métallique 86408790 Operator’s Manual - Clipper Duo Boitier De Prise Adaptateur Reliée À La Terre FIGURE A Adaptateur FIGURE B Languette Pour Vis De Mise À La Terre FIGURE C REMARQUE: Au Canada, l'utilisation d'un adaptateur temporaire n'est pas autorisée par le code canadien de l'électricité. 11 12 Operations Technical Specifications ITEM DIMENSION/CAPACITY Construction Steel chassis with rotationally molded polyethylene tanks Vacuum Motor Three stage, bypass, 1.5 hp (1,119 watts), 100 cfm (2.8m3/min), 120" (3050 mm) waterlift Solution Pump 100 psi (7 bar) - Restorative 50 psi (3.5 bar) - Interim Brush Motor 1/2 hp (604 watts) AC with circuit breaker protection Brushes 2 x 16" (406 mm), ABS core, Perform AlertTM bristle spiral pattern Cleaning Path 16" (40.6 cm) Flow Rate Interim - 0.09 gpm ( 0.37 lpm) Restorative - 1.0 gpm (37.8 lpm) Solution Spray Interim - One quick-disconnect jet Restorative - One quick-disconnect jet Solution Tanks 10 gallons ( 37.8 l) Recovery Tank 10 gallons (37.8 l) Vacuum Shoe 18" (458 mm) wide, cast aluminum Wheels 10" (254 mm) non-marking rubber Power Cable 50' (15 m) detachable Weight 166 lbs (75.3 kg) with cord Special Notes: The sound pressure level at the operator's ear was measured to be 73.7 dBA. This was a nearfield, broad-band measurement taken in a typical industrial environment on a tile floor. This appliance contains no possible source of impact noise. The instantaneous sound pressure level is below 63 Pa. The weighted root mean square acceleration at the operator's arms was measured to be below 2.5m/s2 This was a tri-axial, third-octave-band measurement made during normal operation on a composite tile floor. The measure- ment and related calculations were made in accordance with ISO 5349-1. 86408790 Operator’s Manual - Clipper Duo Operations ITEM MEASURE Height 43 inches (1092 mm) Length 40.5 inches (1029 mm) Width 22 inches (559 mm) Width of scrub path 16 inches (406 mm) WIDTH LENGTH This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. Children should be supervised to ensure that they do not play with the appliance. Cet appareil n'est pas prévu à l'usage des personnes (enfants y compris) avec des possibilités physiques, sensori- elles ou mentales réduites, ou le manque d'expérience et de connaissance, à moins qu'ils aient été donnés la surveillance ou l'instruction au sujet de l'utilisation de l'appareil par une personne chargée de leur sûreté. Des enfants devraient être dirigés pour s'assurer qu'ils ne jouent pas avec l'appareil. HEIGHT 86408790 Operator’s Manual - Clipper Duo 13 14 Operations 86408790 Operator’s Manual - Clipper Duo How this machine works This carpet extractor is an electrical powered, portable carpet extractor intended for commercial use. The appliance sprays a cleaning solution onto the carpet agitates the wet carpet, and then extracts the soiled solution back into the unit's recovery tank. The appliance is fitted with and a hand tool for cleaning upholstery and stairs. The machine is designed to maintain your carpet using the Encapsulating Interim Carpet Cleaning Process. By using the Interim Carpet Maintainer in conjunction with Windsor Red Carpet Encapsulating Interim Cleaning (W450-4) or Encapsulating Interim Cleaning with Carpet Protection (W455-4) chemical solution, you can perform a regular light cleaning and grooming of your carpet very quickly, and have the carpet dry and ready for traffic within 30 minutes. The machine is also designed to restore your carpet using carpet extraction chemicals. The machine is designed to apply cleaning solution onto carpeted floor, scrub the carpet with two counter-rotating brushes, and then vacuum the soiled water back into the recovery tank. The machine's primary systems are the solution system, scrub system, recovery system and operator control system. The function of the solution system is to store mixed solution and deliver solution to the appropriate spray jet. The solution system consists of the solution tank, strainer, extraction pump and interim pump, solenoid valve, spray jets, accessory hand tool, and controls. The solution tank stores solution until it is delivered through the strainer to the appropriate pump. The solenoid valve allows flow from the extraction pump to the extraction nozzle or stops flow at the extraction nozzle so that the accessory hand tool can be used. The interim pump provides flow directly to the interim nozzle. The strainer protects the pump from debris. The solution pumps control the cleaning solution flow. The function of the scrub system is to scrub the carpet, mix the cleaning solution with the soil and lift and groom the carpet pile. The scrub system consists of two cylin- drical brushes, motor, and controls. The brushes scrub the carpet as the motor drives the brushes. The counter-rotating action of the brushes grooms the carpet pile. The function of the recovery system is to vacuum the soiled water back into the recovery tank. The recovery system consists of the vacuum shoe, vacuum motor, float ball filter, recovery tank and controls. The vacuum shoe extracts the dirty solution from the carpet as the machine moves forward. The vacuum motor provides suction to draw the dirty solution off the floor and into the recovery tank. The float ball filter protects the vacuum fan from debris and foam. The recovery tank stores the dirty solution. The function of the operator control system is to allow the operator to select the desired function to perform. This appliance is not suitable for picking up hazardous dust. Cet appareil n'est pas conçu pour aspirer des pous- sières dangereuses. Operations 1 2 3 48 7 6 5 9 Components 1. Control Panel 6. Solution Fill Cover 2. Recovery Dome 7. Solution Drain Hose 3. Recovery Drain Hose 8. Solution Tank 4. Recovery Tank 9. Vacuum Shoe 5. Scrub Deck 86408790 Operator’s Manual - Clipper Duo 15 16 Operations 86408790 Operator’s Manual - Clipper Duo Controls 1. Hand Tool Switch 5. Continuous Spray 2. Main Switch 6. Intermittent Spray 3. Light Cleaning 7. Intermittent Spray Buttons 4. Deep Cleaning 34 512 6 7 Operations Filling The Solution Tank Do not put defoamer, solvents, spotter or prespray chemicals in the solution tank. Do not allow water to spill into vacuum motor inlet. REMOVE SOLUTION FILL COVERDry spills from top of solution tank. Use only the suitable chemicals listed below. Using incompatible chemicals will damage the machine. Damages of this type are not covered under warranty. Carefully read ingredients on manufacturer's label before using any product in this machine. CHEMICALS Suitable Chemicals Non-Compatible Chemicals STEP 1 Alkalis Aldehydes Detergents Aromatic Hydrocarbons Hydroxides SP Butyls ADD WATER 10 Gal. (38 Lt) Soaps Carbon Tetrachloride Clorox Vinegar Chlorinated Bleaches Chlorinated Hydrocarbons Lysol OR Methyl Ethel Ketone (MEK) Perchorethylene (perc) Phenolics Trichlorethylene STEP 2 D-Limonene Product Trademark Names FILL LINE REPLACE SOLUTION FILL COVER STEP 4 86408790 Operator’s Manual - Clipper Duo CHEMICAL ADD CHEMICAL CLEANING LABELING PER STEP 3 17 18 Operations Pre Run Setup 86408790 Operator’s Manual - Clipper Duo Remove electrical cord and literature from recovery tank. Fill solution tank (see filling instructions). Plug cord into grounded outlet. NOTE: Be sure dome is seated on recovery tank, and float shut-off is installed correctly. Switch the cleaning mode switch to the desired process. Press the top of the switch for the encapsulating Interim Carpet Cleaning Process. Press the bottom of the switch for Deep Extraction. Adjust handle to comfortable operating position. Tip machine back by main handle to move to starting point. STEP 1 STEP 2 STEP 3 STEP 4 Operations Lower machine to floor. Select continuous AUTO setting to start solution spray or select intermittent PRESS setting to enable use of trigger switches to start solution spray. The intermittent PRESS setting requires the operator to hold any one of the three trigger switches in the "on" MAIN SWITCH position with the fingers, and is typically used in small areas where short cleaning passes are made. The continuous AUTO setting allows the operator to set the switch in the "on" position with one touch, and is typically used in large areas where long cleaning passes are made. Place main switch in machine cleaning mode to start cleaning process. 86408790 Operator’s Manual - Clipper Duo 19 20 Operations Operating The Machine 1. This machine can be operated in either direction. 2 1 For smaller areas operate the machine by pulling rearward. For larger unobstructed areas, flip the handle and use the machine's brush assisted propelling motion. 2. Start at wall closest to power outlet. For small areas, pull straight back without pushing down on handle. 3. Release intermittent PRESS trigger switches or turn off continuous AUTO setting on solution switch approximately 1 foot before ending cleaning pass. 4. Push down on handle to raise vacuum shoe and brush before moving to the next cleaning pass. Overlap brush contact area approximately 1 inch. 1 in. (25mm) STEP 4 86408790 Operator’s Manual - Clipper Duo STEP 1 STEP 2 1 ft. (30 cm) STEP 3 Operations Start at wall closest to power outlet. For large areas flip handle and operate machine in parallel passes, overlapping brush path. Clean perimeter last. ALTERNATE CLEANING PATH5. During operation, observe the following: This machine is equipped with clear dome to facilitate VACUUM INTAKE operator viewing of dirty solution and vacuum air SOLUTION INTAKE flow. During operation, observe the vacuum intake. Large amounts of water or foam entering the vacuum system can damage the vacuum motor. If you notice either condition, shut down the machine STEP 5 immediately. Empty recovery tank and/or add defoamer to recovery tank. 6. Use right side of machine for cleaning against walls. STEP 6 SHUT CENTER DOWN OFF POSITION 7. After cleaning, turn off all controls, and carefully unplug machine. STEP 7 86408790 Operator’s Manual - Clipper Duo 21 22 Operations To speed drying, use an air mover fan. 86408790 Operator’s Manual - Clipper Duo 8. . Empty recovery tank by releasing recovery drain hose. Use a hose with cold water to clean out the recovery tank. Drain solution tank after each use. RECOVERY DRAIN HOSE SOLUTION DRAIN HOSE STEP 8 Operations Using The Hand Tool 1. Use only acceptable accessory tools. See Optional Accessories section. To connect solution hose pull back collar and insert over machine mounted fitting, then release collar to lock into place. Solution connection can remain HAND TOOL connected at all times. CONNECTION Disconnect vacuum hose and connect the hand SOLUTION QUICK DISCONNECT tool to hand tool connection as shown. HAND TOOL SWITCH 2. Select hand tool switch. 3. Squeeze handle on accessory tool to begin cleaning. 86408790 Operator’s Manual - Clipper Duo 23 24 Maintenance Service Schedule 86408790 Operator’s Manual - Clipper Duo MAINTENANCE DAILY WEEKLY QUARTERLY Check machine for cord damage Check recovery dome and gasket for damage and cleanliness Check brushes - should be clean with no lint or strings attached Remove bearing cap from end of brush. Clean bearing and cap. Inspect vac shoe for blockage; remove fibers with coat hanger, etc. Check hoses for wear, blockages, or damage Check handles, switches, and knobs for damage Run one gallon of water through solution system Clean out recovery tank, clean float screen and check float valve to make sure it moves freely Clean out solution Clean outside of all tanks and check for damage Run vac motor for at least one minute to allow motor to dry Store with dome off tank to allow the tank to dry Check all bearings for noise Check all gaskets for wear and leakage Check pump pressure; observe spray pattern and check with gauge if necessary Check and clean solution screen Check brush for wear; ensure bristles are not damaged Check condition of vac shoe and frame for damage Check overall performance of machine Check vac motor carbon brushes Check belts for wear and replace as necessary Check cables for fraying Maintenance Components 6 2 3A 3B 1. Vacuum Motor 4. Interim Solution Pump 2. Solution Strainer (Inside Tank Fitting) 5. Main Solution Pump 3A. Spray Jet - Extraction 6. Float Shut-Off 3B. Spray Jet - Interim 86408790 Operator’s Manual - Clipper Duo 4 1 LEFT BOTTOM 5 RIGHT 25 26 Maintenance Periodic Maintenance 86408790 Operator’s Manual - Clipper Duo Twice a month, flush a white vinegar solution (One quart vinegar to two gallons of water) or anti-browning solution (mixed as directed) through the extractor. This will prevent build-up of alkaline residue in the system. If spray jets become clogged, remove the spray tips, wash them thoroughly, and blow-dry. NOTE: Do not use pins, wire, etc. to clean nozzles as this could destroy spray pattern. Periodically inspect all hoses, electrical cables and connections on your machine. Frayed or cracked hoses should be repaired or replaced to eliminate vacuum or solution pressure loss. If the cable insulation is broken or frayed, repair or replace it immediately. Do not take chances with electrical fire or shock. Daily / Regular Maintenance NOTE: Before making any adjustments or repairs to the machine, disconnect the power cord from electrical source 1. Empty unused cleaning solution from the solution tank. 2. Flush pumping system with 4 or 7 liters of clean, hot water. 3. After each use, rinse tank with fresh water. Periodi- cally inspect the recovery tank and decontaminate if necessary, using a Hospital Grade Virucide or a 1-10 bleach to water solution. Waste water should be disposed of properly. 4. Check for and remove any lint or debris around vac shoe. 5. Check spray jets for full spray pattern. 6. Remove lint and dirt build-up from brush and housing. 7. Check float and shut-off screen and clean as necessary. Vacuum Shoe and Hose NOTE: Vacuum Shoe and hose flush should be done daily after use. Place machine over drainage area before beginning. 1. Remove vacuum hose from dome. 2. Insert water hose into vacuum hose. 3. With water pressure on high, rinse out hose and vacuum shoe. Water should flow freely from vacuum shoe. Vacuum Hose Maintenance Circuit Protection Circuit Breakers Circuit breakers interrupt the flow of power in the event of an electrical overload. When a circuit breaker is tripped, reset it by pressing the exposed button. If a circuit breaker continues to trip. The cause should be found and corrected.CIRCUIT BREAKERS 15 Amp. Protects the vacuum motor. 8 Amp. Protects the brush motor. 86408790 Operator’s Manual - Clipper Duo 27 28 Maintenance Scrub Deck 1. Scrub Brush Motor 2. Scrub Brushes 3. Retaining Clip 4. Brush Installation Decal 1 2 3 4 86408790 Operator’s Manual - Clipper Duo Maintenance Scrub Head Scrub Brush Replacement The dual cylindrical scrub head is designed to scrub chemical into the carpet. The two counter rotating brushes raise the pile of the carpet, giving it a lush groomed appearance. The rear brush is the stiffer brush and is intended to scrub deeper and help propel the machine. It can be identified by its black color. The front brush is the softer brush and is intended to lift and groom the carpet pile. It can be identified by the white bristles. Maintenance Scrub brushes should be replaced as a set when bristle length wears to height of yellow Perform AlertTM bristles. Scrub Brush Removal The scrub brushes are removed from the right side of the machine. 5. Disconnect all power and unplug machine. 6. Tip the machine back. 7. Pull out on the bottom of the retaining clip. 8. The brush assembly and end cap should drop down. Then pull the brush down far enough to clear the bottom of the housing. 9. Pull brush out with a rocking motion to free brush from drive hub. Bearing Cleaning 1. Remove bearing cap from end of brush. 2. Clean cap and bearings. NOTE: See brush placement decal on brush deck. (Black brush to rear of machine and white brush to front of machine). Only use the brushes provided with the appliance or those specified in the instructions manual. The use of other brushes may impair safety. 1. Lift the drive side of the brush and push it onto drive hub until a positive stop is felt. The brush cannot be installed until the brush is fully seated on the drive hub. 2. Pull out on the bottom of the retaining clip. 3. Line up the end cap with the flats to each side. 4. Slide brush up into the retaining clip until it clicks in place. Only qualified maintenance personnel are to perform the following repairs Seul le personnel d'entretien qualifié peut effectuer des réparations. Vacuum Motor Replacement 1. Turn off all switches and unplug machine. 2. Remove recovery tank. 3. Remove handle mounting assembly and set aside. 4. Disconnect and remove the solution/vacuum frame assembly through the top of the machine. 5. Remove the vacuum motor to service brushes. 6. Reverse process to install vacuum motor. 86408790 Operator’s Manual - Clipper Duo 29 30 Maintenance 86408790 Operator’s Manual - Clipper Duo Vacuum Motor Carbon Brushes The green ground wire must be attached for safe operation. See wiring diagram. Le fil de mise à la terre vert doit être fixé pour assurer un fonctionnement sécuritaire. Voir le schéma de câblage. If armature commutator is grooved, extremely pitted or not concentric, the motor will need to be replaced or sent to a qualified service center. Carbon Brushes 38 [9.5mm] End Cap Important: These brushes wear quicker as the length shortens due to increased heat. Spring inside brush housing will damage motor if brushes are allowed to wear away completely. Periodically check the length of the carbon brushes. Replace both carbon brushes when either is less than 3/8" (9.5mm) long. Maintenance Troubleshooting PROBLEM CAUSE SOLUTION No Power, Nothing Runs Is the cord plugged in. Plug in cord. Circuit breaker tripped in building. Reset breaker. Faulty switch. Call for service. Faulty power cord or pigtail. Call for service. Vacuum Run Motor Will Not Vacuum circuit breaker tripped. Reset breaker. Faulty main vacuum switch. Call for service. Loose wiring. Call for service. Faulty vac motor. Call for service. Vacuum Motor Runs But Suction Is Poor Debris lodged in vac shoe. Remove debris from vac shoe. Dome gasket defective or missing. Replace as necessary. Vacuum hose cracked or hose cuff loose. Replace or repair as necessary. Recovery tank full / float ball stuck in the up position. Turn off vac motor. Drain and rinse recovery tank. Poor Or No Water Flow Pump switch in intermittent position. Turn to continuous or use buttons on handle (Carpet Is Streaky) Jets clogged or missing. Clean using a vinegar /water solution or replace. Solution filter clogged. Drain solution tank and clean solution filter. Faulty solenoid. Call for service. Brush Does Not Spin Main switch off or in hand tool mode. Turn main switch to machine mode. Brush circuit breaker tripped. Reset circuit breaker. Brush belt broken. Replace as necessary. Faulty brush motor. Call for service. 86408790 Operator’s Manual - Clipper Duo 31 32 Suggested Spare Parts 86299250 VACUUM MOTOR 86003630 FLOAT SHUT-OFF 86390390 STRAINER RIGHT 86408790 Operator’s Manual - Clipper Duo BOTTOM 86297440 JET, EXTRACTION 86012550 JET, INTERIM 86298070 PUMP 86201110 PUMP Notes 86408790 Operator’s Manual - Clipper Duo 33

FREE ENGLISH PDF

OPERATING INSTRUCTIONS

USER GUIDE - USER MANUAL

OWNER GUIDE - OWNER MANUAL

REFERENCE GUIDE - REFERENCE MANUAL

INSTRUCTION GUIDE - INSTRUCTION MANUAL