YAESU FTDX101D (01) PDF MANUAL


Report any errors on this page in the comment box below.


PDF OCR Transcript: CAT Operation Reference Manual YAESU MUSEN CO., LTD. CAT (Computer Aided Transceiver) Operation Overview The CAT (Computer Aided Transceiver) System in the FTDX101D transceiver provides control of frequency, VFO, memory, and other settings such as dual-channel memories and diversity reception using an external personal computer. This allows multiple control operations to be fully automated with single mouse clicks, or keystroke operations on the computer keyboard. Using the RS-232C Cable (Refer to figure 1) The FTDX101D transceiver has a built-in level converter, allowing direct connection from the rear-panel RS-232C jack to the serial port of your computer without the need of any external boxes. When using the RS-232C cable, set Menu item [OPERATION SETTING] → [GENERAL] → [TUNER/232C SELECT] to “RS232C”. You will need a serial cable for connection to the RS- 232C (serial or COM port) connector on your computer. Purchase a standard serial cable (not the so-called “null modem” type), ensuring it has the correct gender and number of pins (some serial COM port connectors use a 9-pin rather than 25-pin configuration). If your computer uses a custom connector, you may have to construct the cable. In this case, refer to the technical documentation supplied with your computer for correct data connection. Using the USB Cable (Refer to figure 2) Note: A USB driver is required for remote control from a computer. Download the driver from the Yaesu website (http://www.yaesu.com). The FTDX101D transceiver has a built-in USB to Dual UART Bridge, allowing direct connection from the rear- panel USB jack to the USB jack of your computer without the need of any external boxes. You will need a USB cable to connect to the USB jack on your computer. YAESU MUSEN does not produce CAT System operating software due to the wide variety of per- sonal computers and operating systems in use today. However, the information provided in this chapter explains the serial data structure and opcodes used by the CAT system. This information, along with the short programming examples, is intended to help you start writing programs on your own. As you become more familiar with CAT operation, you can custom- ize programs for your operating needs and utilize the full operating potential of this system. Connection 1 2 3 4 5 6 7 8 9 Pin No. Pin Name I/O Function 1 N/A --- --- 2 SERIAL OUT Output Outputs the Serial Data from the transceiver to the computer. 3 SERIAL IN Input Inputs the Serial Data from the computer to the transceiver. 4 N/A --- --- 5 GND --- Signal Ground 6 N/A --- --- 7 RTS --- --- 8 CTS --- --- 9 N/A --- --- Personal Computer RS-232C “Straight” Cable COM FTDX101D ANT 1 ANT 2 Figure 1ANT 1 ANT 2 RS-232C EXT SPKR KEY METER ACC PTTTUNER GND REM EXT ALC RS-232C A B LINEAR +13.8V Personal Computer FTDX101D Figure 2 USB Cable USB USB EXT SPKR KEY METER ACC PTTTUNER GND REM EXT ALC RS-232C A B LINEAR +13.8V 1 CAT (Computer Aided Transceiver) Operation Control Command A computer control command is composed of an alpha- betical command, various parameters, and the terminator that signals the end of the control command. Example: Set the MAIN Band frequency to 14.250000 MHz. FA 014250000 ; ↑ Command ↑ Parameter ↑ Terminator There are three commands for the FTDX101D as shown below: Set command: Set a particular condition (to the FTDX101D) Read command: Reads an answer (from the FTDX101D) Answer command: Transmits a condition (from the FTDX101D) For example, note the following case of the FA command (Set the MAIN Band frequency): ❒ To set the MAIN Band frequency to 14.250000 MHz, the following command is sent from the computer to the transceiver: “FA014250000;” (Set command) ❒ To read the MAIN Band frequency, the following command is sent from the computer to the transceiver: “FA;” (Read command) ❒ When the Read command above has been sent, the following command is returned to the computer: “FA014250000;” (Answer command) Alphabetical Commands A command consists of 2 alphabetical characters. You may use either lower or upper case characters. The commands available for this transceiver are listed in the “PC Control Command Tables” on the following pages. Parameters Parameters are used to specify information necessary to implement the desired command. The parameters to be used for each command are prede- termined. The number of digits assigned to each parame- ter is also predetermined. Refer to the “Control Command List” and the “Control Command Tables” to configure the appropriate parameters. When configuring parameters, be careful not to make the following mistakes. For example, when the correct parameter is “IS00+1000” (IF SHIFT): IS001000; Not enough parameters specified (No direction (+) given for the IF shift) IS00+100; Not enough digits (Only three frequency digits given) IS00_+_1000; Unnecessary characters between parameters IS00+10000; Too many digits (Five frequency digits given) Note: If a particular parameter is not applicable to the FT- DX101D, the parameter digits should be filled using any character except the ASCII control codes (00 to 1Fh) and the terminator (;). Terminator To signal the end of a command, it is necessary to use a semicolon (;). The digit where this special character must appear differs depending on the command used. 2 CAT (Computer Aided Transceiver) Operation Command Function Set Read Ans. AI AB MAIN BAND TO SUB Band O X X X AC ANTENNA TUNER CONTROL O O O O AG AF GAIN O O O O AI AUTO INFORMATION O O O X AM MAIN BAND TO MEMORY CHANNEL O X X X AN ANTENNA NUMBER O O O O BA SUB BAND TO MAIN BAND O X X X BC AUTO NOTCH O O O O BD BAND DOWN O X X X BI BREAK-IN O O O O BM SUB BAND TO MEMORY CHANNEL O X X X BP MANUAL NOTCH O O O O BS BAND SELECT O X X X BU BAND UP O X X X BY BUSY X O O O CH CHANNEL UP/DOWN O X X X CN CTCSS/DCS NUMBER O O O O CO CONTOUR O O O O CS CW SPOT O O O O CT CTCSS O O O O DA DIMMER O O O X DN DOWN O X X X DT DATE AND TIME O O O X ED ENCORDER DOWN O X X X EM ENCODE MEMORY O O O X EN ENCODE O X X X EU ENCORDER UP O X X X EX MENU O O O O FA FREQUENCY BAND MAIN O O O O FB FREQUENCY BAND SUB O O O O FN FINE TUNING O O O O FS FAST STEP O O O O FT FUNCTION TX O O O O GT AGC FUNCTION O O O O ID IDENTIFICATION X O O X IF INFORMATION X O O O IS IF-SHIFT O O O O KM KEYER MEMORY O O O X KP KEY PITCH O O O O KR KEYER O O O O KS KEY SPEED O O O O KY CW KEYING O X X X LK LOCK O O O O LM LOAD MESSEGE O O O X MA MEMORY CHANNEL TO MAIN BAND O X X X MB MEMORY CHANNEL TO SUB BAND O X X X MC MEMORY CHANNEL O O O X MD MODE O O O O MG MIC GAIN O O O O ML MONITOR LEVEL O O O O MR MEMORY READ X O O X MS METER SW O O O O MT MEMORY CHANNEL WRITE/TAG O O O X MW MEMORY WRITE O X X X MX MOX SET O O O O NA NARROW O O O O NB NOISE BLANKER O O O O Command Function Set Read Ans. AI NL NOISE BLANKER LEVEL O O O O NR NOISE REDUCTION O O O O OI OPPOSITE BAND NFORMATION X O O O OS OFFSET (Repeater Shift) O O O O PA PRE-AMP (IPO) O O O O PB PLAY BACK O O O X PC POWER CONTROL O O O O PL SPEECH PROCESSOR LEVEL O O O O PR SPEECH PROCESSOR O O O O PS POWER SWITCH O O O X QI QMB STORE O X X X QR QMB RECALL O X X X QS QUICK SPLIT O X X X RA RF ATTENUATOR O O O O RC CLAR CLEAR O X X X RD CLAR DOWN O X X X RF ROOFING FILTER O O O O RG RF GAIN O O O O RI RADIO INFORMATION X O O O RL NOISE REDUCTION LEVEL O O O O RM READ METER X O O O RS RADIO STATUS X O O X RT CLAR O O O O RU CLAR UP O X X X SC SCAN O O O O SD SEMI BREAK-IN DELAY TIME O O O O SF SUB DIAL O O O O SH WIDTH O O O O SM S METER X O O X SQ SQUELCH LEVEL O O O O ST SPLIT O O O O SV SWAP VFO O X X X SY SYNC O O O O TX TX SET O O O O UL UNLOCK X O O O UP UP O X X X VD VOX DELAY TIME O O O O VG VOX GAIN O O O O VM [V/M] KEY FUNCTION O X X X VS VFO SELECT O O O O VT VCT(VC TUNE) O O O O VX VOX O O O O XT TX CLAR O O O O ZI ZERO IN O X X X 3 CAT (Computer Aided Transceiver) Operation AB MAIN BAND TO SUB BAND Set 1 2 3 4 5 6 7 8 9 10 A B ; Read 1 2 3 4 5 6 7 8 9 10 Answer 1 2 3 4 5 6 7 8 9 10 AC ANTENNA TUNER CONTROL Set 1 2 3 4 5 6 7 8 9 10 P1 0: Fixed P3 0: Tuner “OFF” A C P1 P2 P3 ; P2 0: Fixed 1: Tuner “ON” Read 1 2 3 4 5 6 7 8 9 10 A C ; 2: Tuning Start / Tuning Stop Answer 1 A 2 3 4 5 C P1 P2 P3 6 ; 7 8 9 10 AG AF GAIN Set 1 2 3 4 5 6 7 8 9 10 P1 0: MAIN BAND A G P1 P2 P2 P2 ; 1: SUB BAND Read 1 2 3 4 5 6 7 8 9 10 P2 000 - 255 A G P1 ; Answer 1 A 2 3 4 5 6 G P1 P2 P2 P2 7 ; 8 9 10 AI AUTO INFORMATION Set 1 2 3 4 5 6 7 8 9 10 P1 0: Auto Information “OFF” A I P1 ; 1: Auto Information “ON” Read 1 2 A I 3 ; 4 5 6 7 8 9 10 This parameter is set to “0” (OFF) automatically when the transceiver is turned “OFF”. Answer 1 A 2 3 4 I P1 ; 5 6 7 8 9 10 AM MAIN BAND TO MEMORY CHANNEL Set 1 2 3 4 5 6 7 8 9 10 A M ; Read 1 2 3 4 5 6 7 8 9 10 Answer 1 2 3 4 5 6 7 8 9 10 AN ANTENNA NUMBER Set 1 2 3 4 5 6 7 8 9 10 P1 0: MAIN BAND A N P1 P2 ; 1: SUB BAND Read 1 2 3 4 A N P1 ; 5 6 7 8 9 10 P2 1: ANT1 2: ANT2 3: ANT3 Answer 1 A 2 3 4 5 N P1 P2 P4 P4 0: Fixed 6 ; 7 8 9 10 BA SUB BAND TO MAIN BAND Set 1 2 3 4 5 6 7 8 9 10 B A ; Read 1 2 3 4 5 6 7 8 9 10 Answer 1 2 3 4 5 6 7 8 9 10 BC AUTO NOTCH Set 1 2 3 4 5 6 7 8 9 10 P1 0: MAIN BAND B C P1 P2 ; 1: SUB BAND Read 1 2 3 4 B C P1 ; 5 6 7 8 9 10 P2 0: Auto Notch “OFF” 1: Auto Notch “ON” Answer 1 B 2 3 4 C P1 P2 5 ; 6 7 8 9 10 4 CAT (Computer Aided Transceiver) Operation BD BAND DOWN Set 1 2 3 4 5 6 7 8 9 10 P1 0: MAIN BAND B D P1 ; 1: SUB BAND Read 1 2 3 4 5 6 7 8 9 10 Answer 1 2 3 4 5 6 7 8 9 10 BI BREAK-IN Set 1 2 3 4 5 6 7 8 9 10 P1 0: Break-in “OFF” B I P1 ; 1: Break-in “ON” Read 1 2 3 4 5 6 7 8 9 10 B I ; Answer 1 B 2 3 4 I P1 ; 5 6 7 8 9 10 BM SUB BAND TO MEMORY CHANNEL Set 1 2 3 4 5 6 7 8 9 10 B M ; Read 1 2 3 4 5 6 7 8 9 10 Answer 1 2 3 4 5 6 7 8 9 10 BP MANUAL NOTCH Set 1 2 3 4 5 6 7 8 9 10 P1 0: MAIN BAND B P P1 P2 P3 P3 P3 ; 1: SUB BAND P3 P2=0 000: “OFF” Read 1 2 3 4 5 B P P1 P2 ; 6 7 8 9 10 P2 0: Manual NOTCH “ON/OFF” 1: Manual NOTCH LEVEL Answer 1 B 001: “ON” P2=1 001 - 320 (NOTCH Frequency : x 10 Hz ) 2 3 4 5 6 7 P P1 P2 P3 P3 P3 8 ; 9 10 BS BAND SELECT Set 1 2 3 4 5 6 7 8 9 10 P1 00: 1.8 MHz 06: 18 MHz B S P1 P1 ; 01: 3.5 MHz 07: 21 MHz 12: MW 13: - Read 1 2 3 4 5 6 7 8 9 10 02: 5 MHz 03: 7 MHz 08: 24.5 MHz 14: - 09: 28 MHz 15: - 04: 10 MHz 10: 50 MHz 16: - Answer 1 2 3 4 5 6 7 8 9 10 05: 14 MHz 11: GEN 17: 70 MHz BU BAND UP Set 1 2 3 4 5 6 7 8 9 10 P1 0: MAIN BAND B U P1 ; 1: SUB BAND Read 1 2 3 4 5 6 7 8 9 10 Answer 1 2 3 4 5 6 7 8 9 10 BY BUSY Set 1 2 3 4 5 6 7 8 9 10 P1 0: MAIN BAND RX BUSY “OFF” 1: MAIN BAND RX BUSY “ON” Read 1 2 3 B Y ; 4 5 6 7 8 9 10 P2 0: SUB BAND RX BUSY “OFF” 1: SUB BAND RX BUSY “ON” Answer 1 B 2 3 4 Y P1 P2 5 ; 6 7 8 9 10 CH CHANNEL UP/DOWN Set 1 2 3 4 5 6 7 8 9 10 P1 0: Memory Channel “UP” C H P1 ; 1: Memory Channel “DOWN” Read 1 2 3 4 5 6 7 8 9 10 Answer 1 2 3 4 5 6 7 8 9 10 5 CAT (Computer Aided Transceiver) Operation CN CTCSS TONE FREQUENCY Set 1 2 3 4 5 6 7 8 9 10 P1 0: MAIN BAND C N P1 P2 P3 P3 P3 ; 1: SUB BAND Read 1 2 3 4 5 C N P1 P2 ; 6 7 8 9 10 P2 0: CTCSS P3 000 - 049: Tone Frequency Number (See Table 1) Answer 1 C 2 3 4 5 6 7 N P1 P2 P3 P3 P3 8 ; 9 10 CO CONTOUR Set Read 1 2 3 4 5 6 7 8 9 10 P1 0: MAIN BAND P3 P2=0 0000: CONTOUR “OFF” C O P1 P2 P3 P3 P3 P3 1 2 3 4 5 6 7 8 C O P1 P2 ; ; 9 1: SUB BAND 10 P2 0: CONTOUR “ON/OFF” 1: CONTOUR FREQ 2: APF “ON/OFF” 0001: CONTOUR “ON” P2=1 0010 - 3200 (CONTOUR Frequency:10 - 3200Hz) P2=2 0000: APF “OFF” Answer 1 C 2 3 4 5 6 7 8 O P1 P2 P3 P3 P3 P3 3: APF FREQ 0001: APF “ON” P2=3 0000 - 0050 (APF Frequency: -250 - 250 Hz ) 9 10 ; CS CW SPOT Set 1 2 3 4 5 6 7 8 9 10 P1 0: OFF C S P1 ; 1: ON Read 1 2 3 4 5 6 7 8 9 10 C S ; Answer 1 C 2 3 S P1 4 ; 5 6 7 8 9 10 CT CTCSS Set 1 2 3 4 5 6 7 8 9 10 P1 0: MAIN BAND C T P1 P2 ; 1: SUB BAND Read 1 2 3 4 C T P1 ; Answer 1 C 5 6 7 8 9 10 P2 0: CTCSS “OFF” 1: CTCSS ENC/DEC 2 3 4 2: CTCSS ENC T P1 P2 5 ; 6 7 8 9 10 Table 1 (CTCSS Tone Chart) 000 67.0 Hz 009 91.5 Hz 018 123.0 Hz 027 162.2 Hz 036 189.9 Hz 045 229.1 Hz 001 69.3 Hz 010 94.8 Hz 019 127.3 Hz 028 165.5 Hz 037 192.8 Hz 046 233.6 Hz 002 71.9 Hz 011 97.4 Hz 020 131.8 Hz 029 167.9 Hz 038 196.6 Hz 047 241.8 Hz 003 74.4 Hz 012 100.0 Hz 021 136.5 Hz 030 171.3 Hz 039 199.5 Hz 048 250.3 Hz 004 77.0 Hz 013 103.5 Hz 022 141.3 Hz 031 173.8 Hz 040 203.5 Hz 049 254.1 Hz 005 79.7 Hz 014 107.2 Hz 023 146.2 Hz 032 177.3 Hz 041 206.5 Hz - - 006 82.5 Hz 015 110.9 Hz 024 151.4 Hz 033 179.9 Hz 042 210.7 Hz - - 007 85.4 Hz 016 114.8 Hz 025 156.7 Hz 034 183.5 Hz 043 218.1 Hz - - 008 88.5 Hz 017 118.8 Hz 026 159.8 Hz 035 186.2 Hz 044 225.7 Hz - - DA DIMMER Set 1 2 3 4 5 6 7 8 9 10 11 P1 00: Fixed D A P1 P1 P2 P2 P3 P3 P4 P4 ; P2 00: Fixed Read 1 2 3 D A ; 4 5 6 7 8 9 10 11 P3 00 - 20: TFT Display Brightness Level P4 00 - 20: LED Indicators Brightness Level Answer 1 D 2 3 4 5 6 7 8 9 10 11 A P1 P1 P2 P2 P3 P3 P4 P4 ; DN MIC DWN Set 1 2 3 4 5 6 7 8 9 10 D N ; Read 1 2 3 4 5 6 7 8 9 10 Answer 1 2 3 4 5 6 7 8 9 10 DT DATE AND TIME Set 1 2 3 4 5 6 7 ~ n-1 n P1 0: Date D T P1 P2 P2 P2 P2 ~ P2 ; 1: Time (UTC) Read 1 2 3 4 D T P1 ; 5 6 7 8 9 10 P2 P1=0 P1=1 yyyymmdd (Year/Month/Date) hhmmss (Hour/Minute/Second, 24 hour time system) Answer 1 D 2 3 4 5 6 7 T P1 P2 P2 P2 P2 ~ n-1 n ~ P2 ; 6 CAT (Computer Aided Transceiver) Operation ED ENCORDER DOWN Set 1 2 3 4 5 6 7 8 9 10 P1 0: MAIN ENCODER E D P1 P2 P2 ; 1: MPVD 5: MAIN CONT ENCODER 6: SUB NOTCH ENCODER Read 1 2 3 4 5 6 7 8 9 10 2: MIC/SPEED ENCODER 7: SUB CONT ENCODER 3: PROC/PITCH ENCODER 8: MULTI Answer 1 2 3 4 5 6 7 8 9 10 4: MAIN NOTCH ENCODER P2 01 - 99: Frequency Steps EM ENCODE MEMORY Set 1 2 3 4 5 6 7 54 55 P1 0: RTTY E M P1 P2 P3 P3 P3 ~ P3 ; 1: DATA Read 1 2 3 4 5 6 7 E M P1 P2 ; 54 55 P2 0: - 1: 1 ch 3: 3 ch 4: 4 ch 2: 2 ch 5: 5 ch Answer 1 E P3 Message Characters (up to 50 characters) (ASCII) 2 3 4 5 6 7 M P1 P2 P3 P3 P3 54 55 ~ P3 ; EN ENCODE Set 1 2 3 4 5 6 7 8 9 10 P1 0: RTTY E N P1 P2 ; 1: DATA Read 1 2 3 4 5 6 7 8 9 10 P2 0: - 1: 1 ch 3: 3 ch 4: 4 ch 2: 2 ch 5: 5 ch Answer 1 2 3 4 5 6 7 8 9 10 EU ENCORDER UP Set 1 2 3 4 5 6 7 8 9 10 P1 0: MAIN ENCODER E U P1 P2 P2 ; 1: MPVD 5: MAIN CONT ENCODER 6: SUB NOTCH ENCODER Read 1 2 3 4 5 6 7 8 9 10 2: MIC/SPEED ENCODER 7: SUB CONT ENCODER 3: PROC/PITCH ENCODER 8: MULTI Answer 1 2 3 4 5 6 7 8 9 10 4: MAIN NOTCH ENCODER P2 01 - 99: Frequency Steps EX MENU Set 1 2 3 4 5 6 7 8 9 nn P1 : 01 - 05 E X P1 P1 P2 P2 P3 P3 P4 ~ P4 ; P2 : 01 - 07 Read 1 2 3 4 5 6 7 8 E X P1 P1 P2 P2 P3 P3 9 ; 10 nn P3 : 01 - 23 P2 : Parameter (See Table) Answer 1 E 2 3 4 5 6 7 8 9 X P1 P1 P2 P2 P3 P3 P4 nn * ~ P4 ; 7 CAT (Computer Aided Transceiver) Operation P1 P2 P3 Function P2 Digits 01 (RADIO SETTING) 01 AGC FAST DELAY 20 ~ 4000 msec (P2= 0020 ~ 4000, 20 msec/step) 4 02 AGC MID DELAY 20 ~ 4000 msec (P2= 0020 ~ 4000, 20 msec/step) 4 03 AGC SLOW DELAY 20 ~ 4000 msec (P2= 0020 ~ 4000, 20 msec/step) 4 04 LCUT FREQ 00: OFF 01: 100 Hz ~ 19: 1000 Hz (50 Hz steps) 2 05 LCUT SLOP 0: 6 dB/oct 1: 18 dB/oct 1 06 HCUT FREQ 00: OFF 01: 700 Hz ~ 67: 4000 Hz (50 Hz steps) 1 01 07 HCUT SLOPE 0: 6 dB/oct 1: 18 dB/oct 1 (MODE SSB) 08 SSB OUT SELECT 0: MAIN 1: SUB 1 09 SSB OUT LEVEL 0 ~ 100 (P2 = 000 ~ 100) 3 10 TX BPF SEL 0: 50 ~ 3050 1: 100 ~ 2900 2: 200 ~ 2800 3: 300 ~ 2700 4: 400 ~ 2600 1 11 SSB MOD SOURCE 0: MIC 1: REAR 1 12 REAR SELECT 0: DATA 1: USB 1 13 RPORT GAIN 0 ~ 100 (P2 = 000 ~ 100) 3 14 RPTT SELECT 0: DAKY 1: RTS 2: DTR 1 02 (MODE AM) 01 AGC FAST DELAY 20 ~ 4000 msec (P2= 0020 ~ 4000, 20 msec/step) 4 02 AGC MID DELAY 20 ~ 4000 msec (P2= 0020 ~ 4000, 20 msec/step) 4 03 AGC SLOW DELAY 20 ~ 4000 msec (P2= 0020 ~ 4000, 20 msec/step) 4 04 LCUT FREQ 00: OFF 01: 100 Hz ~ 19: 1000 Hz (50 Hz steps) 2 05 LCUT SLOP 0: 6 dB/oct 1: 18 dB/oct 1 06 HCUT FREQ 00: OFF 01: 700 Hz ~ 67: 4000 Hz (50 Hz steps) 2 07 HCUT SLOPE 0: 6 dB/oct 1: 18 dB/oct 1 08 AM OUT SELECT 0: MAIN 1: SUB 1 09 AM OUT LEVEL 0 ~ 100 (P2 = 000 ~ 100) 3 10 TX BPF SEL 0: 50 ~ 3050 1: 100 ~ 2900 2: 200 ~ 2800 3: 300 ~ 2700 4: 400 ~ 2600 1 11 AM MOD SOURCE 0: MIC 1: REAR 1 12 MIC GAIN 1000: MCVR 0000 ~ 0100: FIX 1 13 REAR SELECT 0: DATA 1: USB 1 14 RPORT GAIN 0 ~ 100 (P2 = 000 ~ 100) 3 15 RPTT SELECT 0: DAKY 1: RTS 2: DTR 1 03 (MODE FM) 01 AGC FAST DELAY 20 ~ 4000 msec (P2= 0020 ~ 4000, 20 msec/step) 4 02 AGC MID DELAY 20 ~ 4000 msec (P2= 0020 ~ 4000, 20 msec/step) 4 03 AGC SLOW DELAY 20 ~ 4000 msec (P2= 0020 ~ 4000, 20 msec/step) 4 04 LCUT FREQ 00: OFF 01: 100 Hz ~ 19: 1000 Hz (50 Hz steps) 2 05 LCUT SLOP 0: 6 dB/oct 1: 18 dB/oct 1 06 HCUT FREQ 00: OFF 01: 700 Hz ~ 67: 4000 Hz (50 Hz steps) 2 07 HCUT SLOPE 0: 6 dB/oct 1: 18 dB/oct 1 08 FM OUT SELECT 0: MAIN 1: SUB 1 09 FM OUT LEVEL 0 ~ 100 (P2 = 000 ~ 100) 3 10 FM MOD SOURCE 0: MIC 1: REAR 1 11 MIC GAIN 1000: MCVR 0000 ~ 0100: FIX 1 12 REAR SELECT 0: DATA 1: USB 1 13 RPORT GAIN 0 ~ 100 (P2 = 000 ~ 100) 3 14 RPTT SELECT 0: DAKY 1: RTS 2: DTR 1 15 RPT SHIFT(28MHz) 0 ~ 1000 kHz (P2 = 0000 ~ 1000, 10 kHz/step) 4 16 RPT SHIFT(50MHz) 0 ~ 4000 kHz (P2 = 0000 ~ 4000, 10 kHz/step) 4 04 (MODE PSK/DATA) 01 AGC FAST DELAY 20 ~ 4000 msec (P2= 0020 ~ 4000, 20 msec/step) 4 02 AGC MID DELAY 20 ~ 4000 msec (P2= 0020 ~ 4000, 20 msec/step) 4 03 AGC SLOW DELAY 20 ~ 4000 msec (P2= 0020 ~ 4000, 20 msec/step) 4 04 DATA MODE 0: PSK 1: OTHERS 1 05 OTHER SHIFT (SSB) 0 ~ 3000 Hz (P2 = 0000 ~ 3000, 10 Hz steps) 4 06 LCUT FREQ 00: OFF 01: 100 Hz ~ 19: 1000 Hz (50 Hz steps) 2 07 LCUT SLOP 0: 6 dB/oct 1: 18 dB/oct 1 08 HCUT FREQ 00: OFF 01: 700 Hz ~ 67: 4000 Hz (50 Hz steps) 2 09 HCUT SLOPE 0: 6 dB/oct 1: 18 dB/oct 1 10 FM OUT SELECT 0: MAIN 1: SUB 1 11 FM OUT LEVEL 0 ~ 100 (P2 = 000 ~ 100) 3 12 TX BPF SEL 0: 50 ~ 3050 1: 100 ~ 2900 2: 200 ~ 2800 3: 300 ~ 2700 4: 400 ~ 2600 1 13 DATA MOD SOURCE 0: MIC 1: REAR 1 14 REAR SELECT 0: DATA 1: USB 1 15 RPORT GAIN 0 ~ 100 (P2 = 000 ~ 100) 3 16 RPTT SELECT 0: DAKY 1: RTS 2: DTR 1 05 (MODE RTTY) 01 AGC FAST DELAY 20 ~ 4000 msec (P2= 0020 ~ 4000, 20 msec/step) 4 02 AGC MID DELAY 20 ~ 4000 msec (P2= 0020 ~ 4000, 20 msec/step) 4 03 AGC SLOW DELAY 20 ~ 4000 msec (P2= 0020 ~ 4000, 20 msec/step) 4 04 POLARITY-RX 0: NOR 1: REV 1 05 POLARITY-TX 0: NOR 1: REV 1 06 LCUT FREQ 00: OFF 01: 100 Hz ~ 19: 1000 Hz (50 Hz steps) 2 07 LCUT SLOP 0: 6 dB/oct 1: 18 dB/oct 1 08 HCUT FREQ 00: OFF 01: 700 Hz ~ 67: 4000 Hz (50 Hz steps) 2 09 HCUT SLOPE 0: 6 dB/oct 1: 18 dB/oct 1 10 DATA OUT SELECT 0: MAIN 1: SUB 1 11 RTTY OUT LEVEL 0 ~ 100 (P2 = 000 ~ 100) 3 12 SHIFT PORT 0: SHIFT 1: DTR 2: RTS 1 13 MARK FREQUENCY 1: 1275 Hz 2: 2125 Hz 1 14 SHIFT FREQUENCY 1: 170 Hz 1: 200 Hz 2: 425 Hz 3: 850 Hz 1 06 (ENCDEC PSK) 01 PSK MODE 0: BPSK 1: QPSK 1 02 DECODE AFC RANGE 0: 8 1: 1.5 2: 30 Hz 1 03 QPSK POLARITY RX 0: NOR 1: REV 1 04 QPSK POLARITY TX 0: NOR 1: REV 1 05 QPSK TX LEVEL 0 ~ 100 (P2 = 000 ~ 100) 3 8 CAT (Computer Aided Transceiver) Operation P1 P2 P3 Function P2 Digits 01 (RADIO SETTING) 01 RX USOS 0: DISABLE 1: ENABLE 1 02 TX USOS 0: DISABLE 1: ENABLE 1 03 RX NEW LINE CODE 0: CR or LF or CR+LF 1: CR,LF,CR+LF 1 04 TX AUTO CR+LF 0: DISABLE 1: ENABLE 1 05 TX DIDDLE 0: OFF 1: BLANK 2: LTRS 1 06 BAUDOT CODE 0: CCIT 1: US 1 02 (CW SETTING) 07 (ENCDEC RTTY) 01 AGC FAST DELAY 20 ~ 4000 msec (P2= 0020 ~ 4000, 20 msec/step) 4 02 AGC MID DELAY 20 ~ 4000 msec (P2= 0020 ~ 4000, 20 msec/step) 4 03 AGC SLOW DELAY 20 ~ 4000 msec (P2= 0020 ~ 4000, 20 msec/step) 4 04 LCUT FREQ 00: OFF 01: 100 Hz ~ 19: 1000 Hz (50 Hz steps) 2 05 LCUT SLOP 0: 6 dB/oct 1: 18 dB/oct 1 06 HCUT FREQ 00: OFF 01: 700 Hz ~ 67: 4000 Hz (50 Hz steps) 2 07 HCUT SLOPE 0: 6 dB/oct 1: 18 dB/oct 1 01 08 CW OUT SELECT 0: MAIN 1: SUB 1 (MODE CW) 09 CW OUT LEVEL 0 ~ 100 (P2 = 000 ~ 100) 3 10 CW AUTO MODE 0: OFF 1: 50 MHz 2: ON 1 11 CW BK-IN TYPE 0: SEMI 1: FULL 1 12 CW BK-IN DELAY 30 ~ 3000 msec (P2 = 0030 ~ 3000, 10 msec/step) 4 13 CW WAVE SHAPE 0: 1 msec 1: 2 msec 2: 4 msec 3: 6 msec 1 14 CW FREQ DISPLAY 0: DIRECT FREQ 1: PITCH OFFSET 1 15 PC KEYING 0: OFF 1: DAKY 2: RTS 3: DTR 1 16 QSK DELAY TIME 0: 15 msec 1: 20 msec 2: 25 mesc 3: 30 msec 1 02 (KEYER) 01 F KEYER TYPE 0: OFF 1: BUG 2: ELEKEY-A 3: ELEKEY-B 4: ELEKEY-Y 5: ACS 1 02 F KEYER DOT/DASH 0: NOR 1: REV 1 03 R KEYER TYPE 0: OFF 1: BUG 2: ELEKEY-A 3: ELEKEY-B 4: ELEKEY-Y 5: ACS 1 04 R KEYER DOT/DASH 0: NOR 1: REV 1 05 CW WEIGHT 2.5 ~ 4.5 (P2 = 25 ~ 45) 2 06 NUMBER STYLE 0: 1290 1: AUNO 2: AUNT 3: A2NO 4: A2NT 5: 12NO 6: 12NT 1 07 CONTEST NUMBER 001 ~ 999 3 08 CW MEMORY 1 0: TEXT 1: MESSAGE 1 09 CW MEMORY 2 0: TEXT 1: MESSAGE 1 10 CW MEMORY 3 0: TEXT 1: MESSAGE 1 11 CW MEMORY 4 0: TEXT 1: MESSAGE 1 12 CW MEMORY 5 0: TEXT 1: MESSAGE 1 13 REPEAT INTERVAL 1 ~ 60 sec (P2 = 01 ~ 60) 2 03 (DECODE CW) 01 CW DECODE BW 0: 25 1: 50 2: 100 3: 250 (Hz) 1 03 (OPERATION SETTING) 01 DECODE RX SELECT 0: MAIN 1: SUB 1 02 HEADPHONE MIX 0: SEPARATE 1: COMBINE-1 2: COMBINE-2 1 03 ANT3 SELECT 0: TRX 1: RX ANT 04 NB WIDTH 0: 1 ms 1: 3 ms 2: 10 ms 1 05 NB REJECTION 0: 10 dB 1: 30 dB 2: 50 dB 1 06 BEEP LEVEL 0 ~ 100 (P2 = 000 ~ 100) 3 07 RF/SQL VR 0: RF 1: SQL 1 08 TUNER/232C SELECT 0: TUNER 1: RS232C 1 09 232C RATE 0: 4800 bps 1: 9600 bps 2: 19200 bps 3: 38400 bps 1 10 232C TIME OUT TIMER 0: 10 msec 1: 100 msec 2: 1000 msec 3: 3000 msec 1 11 CAT RATE 0: 4800 bps 1: 9600 bps 2: 19200 bps 3: 38400 bps 1 12 CAT TIME OUT TIMER 0: 10 msec 1: 100 msec 2: 1000 msec 3: 3000 msec 1 01 13 CAT RTS 0: DISABLE 1: ENABLE 1 (GENERAL) 14 QMB CH 0: 5ch 1: 10ch 1 15 MEM GROUP 0: DISABLE 1: ENABLE 1 16 QUICK SPLIT INPUT 0: DISABLE 1: ENABLE 1 17 QUICK SPLIT FREQ –20 kHz ~ +00 (or –00) ~ +20 kHz (P2= –20 ~ +00 or –00 ~ +20) 3 18 TX TIME OUT TIMER 0 (OFF) ~ 30 min (P2= 00 ~ 30) 2 19 MIC SCAN 0: DISABLE 1: ENABLE 1 20 MIC SCAN RESUME 0: PAUSE 1: TIME 1 21 REF FREQ ADJ –25 ~ +00 (or –00) ~ +25 (P2= –25 ~ +00 or –00 ~ +25) 3 22 CS DIAL 00: RF POWER 01: MONI LEVEL 02: DNR LEVEL 03: NB LEVEL 04: VOX GAIN 05: VOX DELAY 06: ANTI VOX 07: STEP DIAL 08: MEM CH 09: GROUP 10: R.FIL 2 23 KEYBOARD LANGUAGE 00: JAPANESE 01: ENGLISH(US) 02: ENGLISH(UK) 03: FRENCH 04: FRENCH(CA) 05: GERMAN 06: PORTUGUESE 07: PORTUGUESE(BR) 08: SPANISH 09: SPANISH(LATAM) 10: ITALIAN 2 02 (RX-DSP) 01 APF WIDTH 0: NARROW 1: MEDIUM 2: WIDE 1 02 CONTOUR LEVEL –40 ~ 0 ~ +20 (P2 = –40 ~ –00 or +00 ~ +20) 3 03 CONTOUR WIDTH 01 ~ 11 2 04 DNR LEVEL 01 ~ 15 2 05 IF NOTCH WIDTH 0: NARROW 1: WIDE 1 9 CAT (Computer Aided Transceiver) Operation P1 P2 P3 Function P2 Digits 03 (OPERATION SETTING) 01 PROC TYPE 0: COMP 1: AMC 1 02 AMC RELEASE TIME 0: FAST 1: MID 2: SLOW 1 03 PRMTRC EQ1 FREQ 00 : OFF 01: 100 02: 200 03: 300 04: 400 05: 500 06: 600 07: 700 Hz 2 04 PRMTRC EQ1 LEVEL –10 ~ 0 ~ +10 (P2 = –10 ~ –00 or +00 ~ +10) 3 05 PRMTRC EQ1 BWTH 01 ~ 10 2 06 PRMTRC EQ2 FREQ 00: OFF 01: 700 02: 800 03: 900 04: 1000 05: 1100 06: 1200 07: 1300 08: 1400 09: 1500 Hz 2 07 PRMTRC EQ2 LEVEL –10 ~ 0 ~ +10 (P2 = –10 ~ –00 or +00 ~ +10) 3 08 PRMTRC EQ2 BWTH 01 ~ 10 2 09 PRMTRC EQ3 FREQ 00 : OFF 01: 1500 02: 1600 03: 1700 04: 1800 05: 1900 06: 2000 ~ 18: 3200 Hz 2 03 10 PRMTRC EQ3 LEVEL –10 ~ 0 ~ +10 (P2 = –10 ~ –00 or +00 ~ +10) 3 (TX AUDIO) 11 PRMTRC EQ3 BWTH 01 ~ 10 2 12 P PRMTRC EQ1 FREQ 00 : OFF 01: 100 02: 200 03: 300 04: 400 05: 500 06: 600 07: 700 Hz 2 13 P PRMTRC EQ1 LEVEL –10 ~ 0 ~ +10 (P2 = –10 ~ –00 or +00 ~ +10) 3 14 P PRMTRC EQ1 BWTH 01 ~ 10 2 15 P PRMTRC EQ2 FREQ 00: OFF 01: 700 02: 800 03: 900 04: 1000 05: 1100 06: 1200 07: 1300 08: 1400 09: 1500 Hz 2 16 P PRMTRC EQ2 LEVEL –10 ~ 0 ~ +10 (P2 = –10 ~ –00 or +00 ~ +10) 3 17 P PRMTRC EQ2 BWTH 01 ~ 10 2 18 P PRMTRC EQ3 FREQ 00 : OFF 01: 1500 02: 1600 03: 1700 04: 1800 05: 1900 06: 2000 ~ 18: 3200 Hz 2 19 P PRMTRC EQ3 LEVEL –10 ~ 0 ~ +10 (P2 = –10 ~ –00 or +00 ~ +10) 3 20 P PRMTRC EQ3 BWTH 01 ~ 10 2 04 (TX GNRL) 01 HF MAX POWER 5 ~ 100 (P2 = 005 ~ 100) 3 02 50M MAX POWER 5 ~ 100 (P2 = 005 ~ 100) 3 03 70M MAX POWER 5 ~ 50 (P2 = 005 ~ 050) 3 04 AM MAX POWER 5 ~ 25 (P2 = 005 ~ 025) 3 05 VOX SELECT 0: MIC 1: DATA 1 06 DATA VOX GAIN 0 ~ 100 (P2 = 000 ~ 100) 3 07 EMERGENCY FREQ TX 0: DISABLE 1: ENABLE 1 05 (TUNING) 01 SSB/CW DIAL STEP 0: 5 1: 10 (Hz) 1 02 RTTY/PSK DIAL STEP 0: 5 1: 10 (Hz) 1 03 CH STEP 0: 1 1: 2.5 2: 5 (kHz) 1 04 AM CH STEP 0: 2.5 1: 5 2: 9 3: 10 4: 12.5 5: 25 (kHz) 1 05 FM CH STEP 0: 5 1: 6.25 2: 10 3: 12.5 4: 20 5: 25 (kHz) 1 06 MAIN STEPS PER REV. 0: 250 1: 500 2: 1000 1 07 MPVD STEPS PER REV. 0: 250 1: 500 1 04 (DISPLAY SETTING) 01 MY CALL. Up to 12 characters 12 02 MY CALL TIME 0: OFF 1: 0.5 2: 1 3: 2 4: 3 5: 5 (sec) 1 03 SCREEN SAVER 0: OFF 1: 15 2: 30 3: 60 (min) 1 01 (DISPLAY) 04 TFT CONTRAST 05 DIMMER TFT 00 ~ 20 00 ~ 20 2 2 06 DIMMER LED 00 ~ 20 2 07 MOUSE SPEED POINTER 00 ~ 20 2 08 FREQ STYLE 0: LIGHT 1: BOLD 1 02 (SCOPE) 01 RBW 0: HIGH 1: MID 2: LOW 1 02 SCOPE CTR 0: FILTER 1: CAR POINT 1 03 2D DISP SENSITIVITY 0: NORMAL 1: HI 1 04 3DSS DISP SENSITIVITY 0: NORMAL 1: HI 1 03 (EXT-MONITOR) 01 EXT DISPLAY 0: DISABLE 1: ENABLE 1 02 PIXEL 0: 800x480 1: 800x600 1 05 (EXTENTION SETTING) 01 DAY - - 01 (DATE&TIME) 02 MONTH 03 YEAR 04 HOUR - - - - - - 05 MINUTE - - 02 (SD CARD) 01 MEM LIST LOAD - - 02 MEM LIST SAVE - - 03 MENU LOAD - - 04 MENU SAVE - - 05 INFORMATION - - 06 FIRMWARE UPDATE - - 07 FORMAT - - 03 (SOFT VERSION) 01 - - - 04 (CALIBRATION) 01 - - - 05 (RESET) 01 MEMORY CLEAR - - 02 MENU CLEAR - - 03 ALL RESET - - 10 CAT (Computer Aided Transceiver) Operation FA FREQUENCY MAIN BAND Set 1 2 3 4 5 6 7 8 9 10 P1 000030000 - 075000000 (Hz) F A P1 P1 P1 P1 P1 P1 P1 P1 11 12 13 14 15 16 17 18 19 20 P1 ; Read 1 2 3 4 5 6 7 8 9 10 F A ; Answer 1 2 3 4 5 6 7 8 9 10 F A P1 P1 P1 P1 P1 P1 P1 P1 11 12 13 14 15 16 17 18 19 20 P1 ; FB FREQUENCY SUB BAND Set 1 2 3 4 5 6 7 8 9 10 P1 000030000 - 075000000 (Hz) F B P1 P1 P1 P1 P1 P1 P1 P1 11 12 13 14 15 16 17 18 19 20 P1 ; Read 1 2 3 4 5 6 7 8 9 10 F B ; Answer 1 2 3 4 5 6 7 8 9 10 F B P1 P1 P1 P1 P1 P1 P1 P1 11 12 13 14 15 16 17 18 19 20 P1 ; FN FINE TUNING Set 1 2 3 4 5 6 7 8 9 10 P1 0: Fine Tuning “OFF” F N P1 ; 1: Fine Tuning “ON” Read 1 2 3 4 5 6 7 8 9 10 F N ; Answer 1 F 2 3 N P1 4 ; 5 6 7 8 9 10 FS FAST STEP Set 1 2 3 4 5 6 7 8 9 10 P1 0: MAIN Band FAST Key “OFF” F S P1 ; 1: MAIN Band FAST Key “ON” 2: SUB Band FAST Key “OFF” Read 1 2 3 4 5 6 7 8 9 10 F S ; Answer 1 F 3: SUB Band FAST Key “ON” 4: MAIN Band FAST Key “OFF” / SUB Band FAST Key “OFF” 2 3 4 5 6 7 8 9 10 5: MAIN Band FAST Key “ON” / SUB Band FAST Key “OFF” 6: MAIN Band FAST Key “OFF” / SUB Band FAST Key “ON” S P1 ; 7: MAIN Band FAST Key “ON” / SUB Band FAST Key “ON” FT FUNCTION TX Set 1 2 3 4 5 6 7 8 9 10 P1 0: MAIN Band: TX/RX F T P1 ; 1: SUB Band: TX/RX Read 1 2 3 F T ; 4 5 6 7 8 9 10 2: MAIN Band Transmitter: TX 3: SUB Band Transmitter: TX P2 0: MAIN Band Transmitter: TX Answer 1 F 2 3 4 1: SUB Band Transmitter: TX T P2 ; 5 6 7 8 9 10 GT AGC FUNCTION Set Read 1 2 3 4 5 6 7 8 9 10 P1 0: MAIN Band G T P1 P2 1 2 3 4 G T P1 ; ; 5 1: SUB Band 6 7 8 9 10 P2 0: AGC “OFF” 1: AGC “FAST” 2: AGC “MID” P3 0: AGC “OFF” 1: AGC “FAST” 2: AGC “MID” 3: AGC “SLOW” 4: AGC “AUTO-FAST” Answer 1 G 2 3 4 T P1 P3 5 ; 6 7 8 9 10 3: AGC “SLOW” 4: AGC “AUTO” 5: AGC “AUTO-MID” 6: AGC “AUTO-SLOW” ID IDENTIFICATION Set 1 2 3 4 5 6 7 8 9 10 P1 0681: FTDX101D Read 1 2 3 4 5 6 7 8 9 10 I D ; Answer 1 I 2 3 4 5 6 D P1 P1 P1 P1 7 ; 8 9 10 11 CAT (Computer Aided Transceiver) Operation IF INFORMATION Set 1 2 3 4 5 6 7 8 9 10 P1 001-099 (Memory Channel) P2 VFO-A Frequency (Hz) P3 Clarifier Direction +: Plus Shift, --: Minus Shift Clarifier Offset: 0000 - 9999 (Hz) Read 1 2 3 4 5 6 7 8 9 10 P4 0: RX CLAR “OFF” 1: RX CLAR “ON” I F ; P5 0: TX CLAR “OFF” 1: TX CLAR “ON” P6 MODE 1: LSB 2: USB 3: CW-U 4: FM 5: AM 6: RTTY-L 7: CW-L 8: DATA-L 9: RTTY-U A: DATA-FM B: FM-N C: DATA-U D: AM-N E: PKT F: DATA-FM-N P7 0: VFO 1: Memory 2: Memory Tune 3: Quick Memory Bank (QMB) Answer 4: - 5: PMS P8 0: OFF 1: CTCSS ENC/DEC 2: CTCSS ENC P9 00: (Fixed) P10 0: Simplex 1: Plus Shift 2: Minus Shift 1 2 3 4 5 6 7 8 9 10 I F P1 P1 P1 P2 P2 P2 P2 P2 11 12 13 14 15 16 17 18 19 20 P2 P2 P2 P2 P3 P3 P3 P3 P3 P4 21 22 23 24 25 26 27 28 29 30 P5 P6 P7 P8 P9 P9 P10 ; IS IF-SHIFT Set 1 2 3 4 5 6 7 8 9 10 P1 0: MAIN Band RX I S P1 P2 P3 P4 P4 P4 P4 ; 1: SUB Band RX Read 1 2 3 4 I S P1 ; 5 6 7 8 9 10 P2 0: (Fixed) P3 + / - P4 0 ~ 1200 Hz (20 Hz steps) Answer 1 I 2 3 4 5 6 7 8 9 10 S P1 P2 P3 P4 P4 P4 P4 ; KM KEYER MEMORY Set 1 2 3 4 5 6 7 ~ n-1 n P1 1 - 5 : Keyer Memory Channel Number K M P1 P2 P2 P2 P2 ~ P2 ; P2 Message Characters (up to 50 characters) Read 1 2 3 4 5 6 7 8 9 10 K M P1 ; Answer 1 K 2 3 4 5 6 7 M P1 P2 P2 P2 P2 ~ n-1 n ~ P2 ; KP KEY PITCH Set 1 2 3 4 5 6 7 8 9 10 P1 00: 300 Hz - 75: 1050 Hz (10Hz steps) K P P1 P1 ; Read 1 2 3 4 5 6 7 8 9 10 K P ; Answer 1 K 2 3 4 P P1 P1 5 ; 6 7 8 9 10 KR KEYER Set 1 2 3 4 5 6 7 8 9 10 P1 0: KEYER “OFF” K R P1 ; 1: KEYER “ON” Read 1 2 3 4 5 6 7 8 9 10 K R ; Answer 1 K 2 3 R P1 4 ; 5 6 7 8 9 10 KS KEY SPEED Set 1 2 3 4 5 6 7 8 9 10 P1 004 - 060 (WPM) K S P1 P1 P1 ; Read 1 2 3 4 5 6 7 8 9 10 K S ; Answer 1 K 2 3 4 5 S P1 P1 P1 6 ; 7 8 9 10 KY CW KEYING Set 1 2 3 4 5 6 7 8 9 10 P1 1: Keyer Memory “1” Playback 6: Message Keyer “1” Playback K Y P1 ; 2: Keyer Memory “2” Playback 7: Message Keyer “2” Playback Read 1 2 3 4 5 6 7 8 9 10 3: Keyer Memory “3” Playback 8: Message Keyer “3” Playback 4: Keyer Memory “4” Playback 9: Message Keyer “4” Playback 5: Keyer Memory “5” Playback A: Message Keyer “5” Playback Answer 1 2 3 4 5 6 7 8 9 10 12 CAT (Computer Aided Transceiver) Operation LK LOCK Set 1 2 3 4 5 6 7 8 9 10 P1 0: MAIN Band DIAL Lock “OFF” L K P1 ; 1: MAIN Band DIAL Lock “ON” 2: SUB Band DIAL Lock “OFF” Read 1 2 3 4 5 6 7 8 9 10 L K ; Answer 1 L 3: SUB Band DIAL Lock “ON” 4: MAIN Band DIAL Lock “OFF” / SUB Band DIAL Lock “OFF” 2 3 5: MAIN Band DIAL Lock “ON” / SUB Band DIAL Lock “OFF” 6: MAIN Band DIAL Lock “OFF” / SUB Band DIAL Lock “ON” K P1 7: MAIN Band DIAL Lock “ON” / SUB Band DIAL Lock “ON” 4 ; 5 6 7 8 9 10 LM LOAD MESSEGE Set 1 2 3 4 5 6 7 8 9 10 P1 0: DVS P2 0: DVS (Recording Stop) L M P1 P2 ; 1: DVS (CH “1” Recording Start/Stop) Read 1 2 3 4 5 6 7 8 9 10 L M P1 ; 2: DVS (CH “2” Recording Start/Stop) 3: DVS (CH “3” Recording Start/Stop) 4: DVS (CH “4” Recording Start/Stop) Answer 1 L 2 3 4 5 5: DVS (CH “5” Recording Start/Stop) M P1 P2 ; 6 7 8 9 10 MA MEMORY CHANNEL TO MAIN BAND Set 1 2 3 4 5 6 7 8 9 10 M A ; Read 1 2 3 4 5 6 7 8 9 10 Answer 1 2 3 4 5 6 7 8 9 10 MB MEMORY CHANNEL TO SUB BAND Set 1 2 3 4 5 6 7 8 9 10 M B ; Read 1 2 3 4 5 6 7 8 9 10 Answer 1 2 3 4 5 6 7 8 9 10 MC MEMORY CHANNEL Set 1 2 3 4 5 6 7 8 9 10 P1 001 - 099: Regular Memory Channel M C P1 P1 P1 ; P1L: P1L P1U: P1U ~ P9L: P9L P9U: P9U Read 1 2 3 4 5 6 7 8 9 10 M C ; EMG: EMG Answer 1 M 2 3 4 5 C P1 P1 P1 6 ; 7 8 9 10 MD OPERATING MODE Set 1 2 3 4 5 6 7 8 9 10 P1 0: MAIN Band RX M D P1 P2 ; 1: SUB Band RX Read 1 2 3 4 5 6 7 8 9 10 P2 MODE M D P1 ; 1: LSB 2: USB 3: CW-U 4: FM 5: AM 6: RTTY-L 7: CW-L 8: DATA-L 9: RTTY-U A: DATA-FM B: FM-N C: DATA-U D: AM-N E: PKT F: DATA-FM-N Answer 1 M 2 3 4 D P1 P2 5 ; 6 7 8 9 10 MG MIC GAIN Set 1 2 3 4 5 6 7 8 9 10 P1 000 - 100 M G P1 P1 P1 ; Read 1 2 3 4 5 6 7 8 9 10 M G ; Answer 1 M 2 3 4 5 G P1 P1 P1 6 ; 7 8 9 10 ML MONITOR LEVEL Set Read 1 2 3 4 5 6 7 8 9 10 P1 0: MONI “ON/OFF” M L P1 P2 P2 P2 ; 1 2 3 4 5 6 7 M L P1 ; 1: MONI Level 8 9 10 P2 P1=0 000: MONI “OFF” 001: MONI “ON” Answer 1 M 2 3 4 5 6 L P1 P2 P2 P2 7 ; 8 9 10 P1=1 000 - 100 13 CAT (Computer Aided Transceiver) Operation MR MEMORY CHANNEL READ Set 1 2 3 4 5 6 7 8 9 10 P0/1 001-099 (Memory Channel) P2 VFO-A Frequency (Hz) P3 Clarifier Direction +: Plus Shift, --: Minus Shift Read 1 2 3 4 5 6 7 8 9 10 Clarifier Offset: 0000 - 9999 (Hz) P4 0: RX CLAR “OFF” 1: RX CLAR “ON” M R P0 P0 P0 ; P5 0: TX CLAR “OFF” 1: TX CLAR “ON” P6 MODE 1: LSB 2: USB 3: CW-U 4: FM 5: AM 6: RTTY-L 7: CW-L 8: DATA-L 9: RTTY-U A: DATA-FM B: FM-N C: DATA-U D: AM-N E: PKT F: DATA-FM-N Answer P7 0: VFO 1: Memory P8 0: CTCSS “OFF” 1: CTCSS ENC/DEC 2: CTCSS ENC P9 00: (Fixed) P10 0: Simplex 1: Plus Shift 2: Minus Shift 1 2 3 4 5 6 7 8 9 10 M R P1 P1 P1 P2 P2 P2 P2 P2 11 12 13 14 15 16 17 18 19 20 P2 P2 P2 P2 P3 P3 P3 P3 P3 P4 21 22 23 24 25 26 27 28 29 30 P5 P6 P7 P8 P9 P9 P10 ; MS METER SW Set 1 2 3 4 5 6 7 8 9 10 P1 MAIN P2 SUB M S P1 P2 ; 0: POW 0: ALC Read 1 2 3 4 5 6 7 8 9 10 M S ; 1: COMP 2: TEMP 1: VDD 2: ID 3: SWR Answer 1 M 2 3 4 S P1 P2 5 ; 6 7 8 9 10 MT MEMORY CHANNEL WRITE/TAG Set 1 2 3 4 5 6 7 8 9 10 P0/1 001-099 (Memory Channel) P2 VFO-A Frequency (Hz) M 11 T 12 P1 13 P1 14 P1 15 P2 16 P2 17 P2 18 P2 19 P2 20 P3 Clarifier Direction +: Plus Shift, --: Minus Shift Clarifier Offset: 0000 - 9999 (Hz) P4 0: RX CLAR “OFF” 1: RX CLAR “ON” P2 P2 P2 P2 P3 P3 P3 P3 P3 P4 P5 0: TX CLAR “OFF” 1: TX CLAR “ON” 21 22 23 24 25 26 27 P5 P6 P7 P8 P9 P9 P10P11P12P12 28 29 30 P6 MODE 1: LSB 2: USB 3: CW-U 4: FM 8: DATA-L 9: RTTY-U A: DATA-FM 5: AM 6: RTTY-L 7: CW-L B: FM-N C: DATA-U D: AM-N E: PKT F: DATA-FM-N 31 32 33 34 35 36 37 38 39 40 P7 Set: 0: (Fixed) / Read: 0: VFO 1: Memory P12 P12 P12 P12 P12 P12 P12 P12 P12 P12 P8 P9 0: CTCSS “OFF” 1: CTCSS ENC/DEC 2: CTCSS ENC 00: (Fixed) 41 42 43 44 45 46 47 48 49 50 P10 0: Simplex 1: Plus Shift 2: Minus Shift Read ; 1 P11 0: (Fixed) 2 3 4 5 6 7 8 9 10 P12 TAG Characters (up to 12 characters) (ASCII) M T P0 P0 P0 ; Answer 1 2 3 4 5 6 7 8 9 10 M T P1 P1 P1 P2 P2 P2 P2 P2 11 12 13 14 15 16 17 18 19 20 P2 P2 P2 P2 P3 P3 P3 P3 P3 P4 21 22 23 24 25 26 27 28 29 30 P5 P6 P7 P8 P9 P9 P10P11P12P12 31 32 33 34 35 36 37 38 39 40 P12 P12 P12 P12 P12 P12 P12 P12 P12 P12 41 42 43 44 45 46 47 48 49 50 ; MW MEMORY CHANNEL WRITE Set 1 2 3 4 5 6 7 8 9 10 P1 001-099 (Memory Channel) P2 Frequency (Hz) M 11 W P1 12 13 P1 14 P1 15 P2 16 P2 17 P2 18 P2 19 P2 20 P3 Clarifier Direction +: Plus Shift, --: Minus Shift Clarifier Offset: 0000 - 9999 (Hz) P4 0: RX CLAR “OFF” 1: RX CLAR “ON” P2 P2 P2 P2 P3 P3 P3 P3 P3 P4 P5 0: TX CLAR “OFF” 1: TX CLAR “ON” 21 22 23 24 25 26 27 28 P5 P6 P7 P8 P9 P9 P10 ; 29 30 P6 MODE 1: LSB 2: USB 3: CW-U 4: FM 8: DATA-L 9: RTTY-U A: DATA-FM 5: AM 6: RTTY-L 7: CW-L B: FM-N C: DATA-U D: AM-N E: PKT F: DATA-FM-N Read 1 2 3 4 5 6 7 8 9 10 P7 00: (Fixed) P8 0: CTCSS “OFF” 1: CTCSS ENC/DEC 2: CTCSS ENC P9 00: (Fixed) Answer 1 2 3 4 5 6 7 8 9 10 P10 0: Simplex 1: Plus Shift 2: Minus Shift MX MOX SET Set 1 2 3 4 5 6 7 8 9 10 P1 0: MOX “OFF” M X P1 ; 1: MOX “ON” Read 1 2 3 4 5 6 7 8 9 10 M X ; Answer 1 M 2 3 X P1 4 ; 5 6 7 8 9 10 14 CAT (Computer Aided Transceiver) Operation NA NARROW Set 1 2 3 4 5 6 7 8 9 10 P1 0: MAIN Band M A P1 P2 ; 1: SUB Band Read 1 2 3 4 M A P1 ; 5 6 7 8 9 10 P2 0: OFF 1: ON Answer 1 M 2 3 4 A P1 P2 5 ; 6 7 8 9 10 NB NOISE BLANKER STATUS Set 1 2 3 4 5 6 7 8 9 10 P1 0: MAIN Band N B P1 P2 ; 1: SUB Band Read 1 2 3 4 N B P1 ; 5 6 7 8 9 10 P2 0: Noise Blanker “OFF” 1: Noise Blanker “ON” Answer 1 N 2 3 4 B P1 P2 5 ; 6 7 8 9 10 NL NOISE BLANKER LEVEL Set 1 2 3 4 5 6 7 8 9 10 P1 0: Fixed N L P1 P2 P2 P2 ; P2 000 - 010 Read 1 2 3 4 5 6 7 8 9 10 N L P1 ; Answer 1 N 2 3 4 5 6 L P1 P2 P2 P2 7 ; 8 9 10 NR NOISE REDUCTION Set 1 2 3 4 5 6 7 8 9 10 P1 0: MAIN Band N R P1 P2 ; 1: SUB Band Read 1 2 3 4 N R P1 ; 5 6 7 8 9 10 P2 0: Noise Reduction “OFF” 1: Noise Reduction “ON” Answer 1 N 2 3 4 R P1 P2 5 ; 6 7 8 9 10 OI OPPOSITE BAND INFORMATION Set 1 2 3 4 5 6 7 8 9 10 P1 001-099 (Memory Channel) P2 VFO-B Frequency (Hz) P3 Clarifier Direction +: Plus Shift, --: Minus Shift Read 1 2 3 4 5 6 7 8 9 10 Clarifier Offset: 0000 - 9999 (Hz) P4 0: RX CLAR “OFF” 1: RX CLAR “ON” O I ; P5 0: TX CLAR “OFF” 1: TX CLAR “ON” 1 O 2 I 3 P1 4 P1 5 P1 6 P2 7 P2 8 P2 9 P2 10 P2 P6 MODE 1: LSB 2: USB 3: CW-U 4: FM 8: DATA-L 9: RTTY-U A: DATA-FM D: AM-N E: PKT E: DATA-FM-N 5: AM 6: RTTY-L 7: CW-L B: FM-N C: DATA-U Answer 11 P2 12 13 14 15 16 17 18 19 20 P7 0: VFO 1: Memory P2 P2 P2 P3 P3 P3 P3 P3 P4 P8 0: CTCSS “OFF” P9 0: (Fixed) 1: CTCSS ENC/DEC 2: CTCSS ENC 21 22 23 24 25 26 27 28 29 30 P10 0: Simplex 1: Plus Shift 2: Minus Shift P5 P6 P7 P8 P9 P9 P10 ; OS OFFSET (REPEATER SHIFT) Set 1 2 3 4 5 6 7 8 9 10 P1 0: MAIN Band O S P1 P2 ; 1: SUB Band Read 1 2 3 4 O S P1 ; 5 6 7 8 9 10 P2 0: Simplex 1: Plus Shift 2: Minus Shift Answer 1 O 2 3 4 5 : This command can be activated only with an FM mode. S P1 P2 ; 6 7 8 9 10 PA PRE-AMP (IPO) Set 1 2 3 4 5 6 7 8 9 10 P1 0: MAIN Band P A P1 P2 ; 1: SUB Band Read 1 2 3 4 P A P1 ; 5 6 7 8 9 10 P2 0: IPO 1: AMP 1 2: AMP 2 Answer 1 P 2 3 4 A P1 P2 5 ; 6 7 8 9 10 15 CAT (Computer Aided Transceiver) Operation PB PLAY BACK Set 1 2 3 4 5 6 7 8 9 10 P1 0: DVS P2 0: DVS (Playback Stop) P B P1 P2 ; 1: DVS (CH “1” Playback Start) Read 1 2 3 4 5 6 7 8 9 10 P B P1 ; Answer 1 P 2: DVS (CH “2” Playback Start) 3: DVS (CH “3” Playback Start) 4: DVS (CH “4” Playback Start) 5: DVS (CH “5” Playback Start) 2 3 4 B P1 P2 5 ; 6 7 8 9 10 PC POWER CONTROL Set 1 2 3 4 5 6 7 8 9 10 P1 005 -100 P C P1 P1 P1 ; Read 1 2 3 4 5 6 7 8 9 10 P C ; Answer 1 P 2 3 4 5 C P1 P1 P1 6 ; 7 8 9 10 PL SPEECH PROCESSOR LEVEL Set 1 2 3 4 5 6 7 8 9 10 P1 000 -100 P L P1 P1 P1 ; Read 1 2 3 4 5 6 7 8 9 10 P L ; Answer 1 P 2 3 4 5 L P1 P1 P1 6 ; 7 8 9 10 PR SPEECH PROCESSOR LEVEL Set 1 2 3 4 5 6 7 8 9 10 P1 0: Speech Processor P R P1 P2 ; 1: Parametric Microphone Equalizer Read 1 2 3 4 P R P1 ; 5 6 7 8 9 10 P2 1: “OFF” 2: “ON” Answer 1 P 2 3 4 R P1 P2 5 ; 6 7 8 9 10 PS POWER SWITCH Set 1 2 3 4 5 6 7 8 9 10 P1 0: POWER “OFF” P S P1 ; 1: POWER “ON” Read 1 2 3 P S ; 4 5 6 7 8 9 10 This command requires dummy data be initially sent. Then after one second and before two seconds the command is sent. Answer 1 P 2 3 S P1 4 ; 5 6 7 8 9 10 QI QMB STORE Set 1 2 3 4 5 6 7 8 9 10 Q I ; Read 1 2 3 4 5 6 7 8 9 10 Answer 1 2 3 4 5 6 7 8 9 10 QR QMB RECALL Set 1 2 3 4 5 6 7 8 9 10 Q R ; Read 1 2 3 4 5 6 7 8 9 10 Answer 1 2 3 4 5 6 7 8 9 10 QS QUICK SPLIT Set 1 2 3 4 5 6 7 8 9 10 Q S ; Read 1 2 3 4 5 6 7 8 9 10 Answer 1 2 3 4 5 6 7 8 9 10 16 CAT (Computer Aided Transceiver) Operation RA RF ATTENUATOR Set 1 2 3 4 5 6 7 8 9 10 P1 0: MAIN Band R A P1 P2 ; 1: SUB Band Read 1 2 3 4 R A P1 ; Answer 1 R 5 6 7 8 9 10 P2 0: OFF 1: 6dB 2: 12dB 3: 18dB 2 3 4 A P1 P2 5 ; 6 7 8 9 10 RC CLAR CLEAR Set 1 2 3 4 5 6 7 8 9 10 R C ; Read 1 2 3 4 5 6 7 8 9 10 Answer 1 2 3 4 5 6 7 8 9 10 RD CLAR DOWN Set 1 2 3 4 5 6 7 8 9 10 P1 0000 - 9999 (Hz) R D P1 P1 P1 P1 ; Read 1 2 3 4 5 6 7 8 9 10 Answer 1 2 3 4 5 6 7 8 9 10 RF ROOFING FILTER Set 1 2 3 4 5 6 7 8 9 10 P1 0: MAIN Band R F P1 P2 ; 1: SUB Band Read 1 2 3 4 R F P1 ; 5 6 7 8 9 10 P2 1: 12kHz 2: 3kHz 3: 1.2kHz (option) Answer 1 R 2 3 4 4: 600Hz F P1 P2 5: 300Hz (option) 5 ; 6 7 8 9 10 RG RF GAIN Set 1 2 3 4 5 6 7 8 9 10 P1 0: MAIN Band R G P1 P2 P2 P2 ; 1: SUB Band Read 1 2 3 4 5 6 7 8 9 10 P2 000 - 255 R G P1 ; Answer 1 R 2 3 4 5 6 G P1 P2 P2 P2 7 ; 8 9 10 RI RADIO INFORMATION Set 1 2 3 4 5 6 7 8 9 10 P1 0: Hi-SWR 3: REC Read 1 2 3 4 R I P1 ; Answer 1 R 5 6 7 8 9 10 4: PLAY P2 0: OFF 2 3 4 5 1: ON I P1 P2 ; 6 7 8 9 10 RL NOISE REDUCTION LEVEL Set 1 2 3 4 5 6 7 8 9 10 P1 0: MAIN Band R L P1 P2 P2 ; 1: SUB Band Read 1 2 3 4 5 6 7 8 9 10 P2 01 - 15 R L P1 ; Answer 1 R 2 3 4 5 L P1 P2 P2 6 ; 7 8 9 10 RM READ METER Set 1 2 3 4 5 6 7 8 9 10 P1=0 P2: Left side Meter 0 - 255 Read 1 2 3 4 R M P1 ; 5 6 7 8 9 10 P3: Right side Meter 0 - 255 P1= 1: S (MAIN Band) 2: S (SUB Band) 3: COMP 6: SWR 7: IDD 4: ALC 5: PO 8: VDD 9: TEMP Answer 1 R 2 3 4 5 6 7 8 9 10 M P1 P2 P2 P2 P3 P3 P3 ; P2: 0 - 255 P3: 0 17 CAT (Computer Aided Transceiver) Operation RS RADIO STATUS Set 1 2 3 4 5 6 7 8 9 10 P1 0: NORMAL MODE 1: MENU MODE Read 1 2 3 4 5 6 7 8 9 10 R S ; Answer 1 R 2 3 S P1 4 ; 5 6 7 8 9 10 RT CLAR Set 1 2 3 4 5 6 7 8 9 10 P1 0: RX Clarifier “OFF” R T P1 ; 1: RX Clarifier “ON” Read 1 2 3 4 5 6 7 8 9 10 R T ; Answer 1 R 2 3 T P1 4 ; 5 6 7 8 9 10 RU RX CLARIFIER PLUS OFFSET Set 1 2 3 4 5 6 7 8 9 10 P1 0000 - 9999 (Hz) R U P1 P1 P1 P1 ; Read 1 2 3 4 5 6 7 8 9 10 Answer 1 2 3 4 5 6 7 8 9 10 SC SCAN Set 1 2 3 4 5 6 7 8 9 10 P1 0: Scan “OFF” S C P1 ; 1: Scan “ON” (UP ward) Read 1 2 3 4 5 6 7 8 9 10 S C ; 2: Scan “ON” (DOWN ward) Answer 1 S 2 3 C P1 4 ; 5 6 7 8 9 10 SD CW BREAK-IN DELAY TIME Set 1 2 3 4 5 6 7 8 9 10 P1 0030 - 3000 msec S D P1 P1 P1 P1 ; Read 1 2 3 4 5 6 7 8 9 10 S D ; Answer 1 S 2 3 4 5 6 D P1 P1 P1 P1 7 ; 8 9 10 SF SUB DIAL Set 1 2 3 4 5 6 7 8 9 10 P1 0: MPVD S F P1 P2 ; 1: MULTI knob P2 P1=0 Read 1 2 3 4 5 6 7 8 9 10 S F P1 ; 1: CLAR 2: VCT 3: SUB 4: CS P1=1 Answer 1 S 2 3 4 5 0: RF POWER 1: MONI LEVEL 2: DNR LEVEL 3: NB LEVEL 4: VOX GAIN 5: VOX DELAY 6: ANTI VOX 7: STEP DIAL 8: MEM CH 9: GROUP F P1 P2 ; A: R.FIL B: SPEED C: PEAK D: COLOR E: LEVEL 6 7 8 9 10 18 CAT (Computer Aided Transceiver) Operation SH WIDTH Set 1 2 3 4 5 6 7 8 9 10 P1 0: MAIN Band S H P1 P2 P3 P3 ; 1: SUB Band Read 1 2 3 4 5 6 7 8 9 10 P2 0 (Fixed) S H P1 ; P3 00 (See Table) Answer 1 S 2 3 4 5 6 H P1 P2 P3 P3 7 ; 8 9 10 Command Bandwidth P3 SSB (Narrow) SSB (Wide) CW (Narrow) CW (Wide) RTTY (Narrow) RTTY (Wide) PSK (Narrow) PSK (Wide) 00 (Default) 1500 Hz 2400 Hz 500 Hz 2400 Hz 300 Hz 500 Hz 300 Hz 500 Hz 01 200 Hz - 50 Hz - 50 Hz - 50 Hz - 02 400 Hz - 100 Hz - 100 Hz - 100 Hz - 03 600 Hz - 150 Hz - 150 Hz - 150 Hz - 04 850 Hz - 200 Hz - 200 Hz - 200 Hz - 05 1100 Hz - 250 Hz - 250 Hz - 250 Hz - 06 1350 Hz - 300 Hz - 300 Hz - 300 Hz - 07 1500 Hz - 350 Hz - 350 Hz - 350 Hz - 08 1650 Hz - 400 Hz - 400 Hz - 400 Hz - 09 1800 Hz 1800 Hz 450 Hz - 450 Hz - 450 Hz - 10 - 1950 Hz 500 Hz 500 Hz 500 Hz 500 Hz 500 Hz 500 Hz 11 - 2100 Hz - 600 Hz - 600 Hz - 600 Hz 12 - 2200 Hz - 800 Hz - 800 Hz - 800 Hz 13 - 2300 Hz - 1200 Hz - 1200 Hz - 1200 Hz 14 - 2400 Hz - 1400 Hz - 1400 Hz - 1400 Hz 15 - 2500 Hz - 1700 Hz - 1700 Hz - 1700 Hz 16 - 2600 Hz - 2000 Hz - 2000 Hz - 2000 Hz 17 - 2700 Hz - 2400 Hz - 2400 Hz - 2400 Hz 18 - 2800 Hz - 3000 Hz - 3000 Hz - 3000 Hz 19 - 2900 Hz - - - - - - 20 - 3000 Hz - - - - - - 21 - 3200 Hz - - - - - - SM S-METER READING Set 1 2 3 4 5 6 7 8 9 10 P1 0: MAIN Band 1: SUB Band Read 1 2 3 4 5 6 7 8 9 10 P2 000 - 255 S M P1 ; Answer 1 S 2 3 4 5 6 M P1 P2 P2 P2 7 ; 8 9 10 SQ SQUELCLH LEVEL Set 1 2 3 4 5 6 7 8 9 10 P1 0: Fixed S Q P1 P2 P2 P2 ; P2 000 - 100 Read 1 2 3 4 5 6 7 8 9 10 S Q P1 ; Answer 1 S 2 3 4 5 6 Q P1 P2 P2 P2 7 ; 8 9 10 ST SPLIT Set 1 2 3 4 5 6 7 8 9 10 P1 0: SPLIT “OFF” S T P1 ; 1: SPLIT “ON” Read 1 2 3 4 5 6 7 8 9 10 S T ; 2: SPLIT “ON” + 5 kHz Up Answer 1 S 2 3 T P1 4 ; 5 6 7 8 9 10 SV SWAP VFO Set 1 2 3 4 5 6 7 8 9 10 Exchanges the MAIN band and SUB band frequency data. S V ; Read 1 2 3 4 5 6 7 8 9 10 Answer 1 2 3 4 5 6 7 8 9 10 SY SYNC Set 1 2 3 4 5 6 7 8 9 10 P1 0: SYNC “OFF” S Y P1 ; 1: SYNC “ON” Read 1 2 3 4 5 6 7 8 9 10 S Y ; 2: SYNC “ON” + Copy (Frequency, Mode) Answer 1 S 2 3 Y P1 4 ; 5 6 7 8 9 10 19 CAT (Computer Aided Transceiver) Operation TX TX SET Set 1 2 3 4 5 6 7 8 9 10 P1 0: RADIO TX “OFF” CAT TX “OFF” T X P1 ; 1: RADIO TX “OFF” CAT TX “ON” Read 1 2 3 4 5 6 7 8 9 10 T X ; 2: RADIO TX “ON” CAT TX “OFF” (Answer) Answer 1 T 2 3 X P1 4 ; 5 6 7 8 9 10 UL PLL UNLOCK STATUS Set 1 2 3 4 5 6 7 8 9 10 P1 0: PLL “Lock” 1: PLL “Unlock” Read 1 2 3 4 5 6 7 8 9 10 U L ; Answer 1 U 2 3 L P1 4 ; 5 6 7 8 9 10 UP MIC UP Set 1 2 3 4 5 6 7 8 9 10 U P ; Read 1 2 3 4 5 6 7 8 9 10 Answer 1 2 3 4 5 6 7 8 9 10 VD VOX DELAY TIME / DATA VOX DELAY TIME Set 1 2 3 4 5 6 7 8 9 10 P1 0030 - 3000 msec (10 msec multiples) V D P1 P1 P1 P1 ; VD command has different parameters to be changed according to the setting of Menu Read 1 2 3 V D ; Answer 1 V 4 5 6 7 8 9 10 item [OPERATION SETTING] → [TX GENERAL] → [VOX SELECT]. “MIC”: VOX DELAY 2 3 4 5 6 “DATA”: DATA VOX DELAY D P1 P1 P1 P1 7 ; 8 9 10 VG VOX GAIN Set 1 2 3 4 5 6 7 8 9 10 P1 000 - 100 V G P1 P1 P1 ; Read 1 2 3 4 5 6 7 8 9 10 V G ; Answer 1 V 2 3 4 5 G P1 P1 P1 6 ; 7 8 9 10 VM MAIN BAND TO MEMORY CHANNEL Set 1 2 3 4 5 6 7 8 9 10 V M ; ; Read 1 2 3 4 5 6 7 8 9 10 Answer 1 2 3 4 5 6 7 8 9 10 VS VFO SELECT Set 1 2 3 4 5 6 7 8 9 10 P1 0: MAIN Band Operation V S P1 ; 1: Sub Band Operation Read 1 2 3 4 5 6 7 8 9 10 V S ; Answer 1 V 2 3 S P1 4 ; 5 6 7 8 9 10 VT VCT (VC TUNE) Set 1 2 3 4 5 6 7 8 9 10 P1 0: MAIN Band V T P1 P2 P3 P4 ; 1: SUB Band P4 0 ~ 9 P5 0 ~ 255 (VCT Meter) Read 1 2 3 4 V T P1 ; 5 6 7 8 9 10 P2 0: OFF 1: ON 2: Default P6 0: VC TUNE (not installed) 1: VC TUNE Answer 1 V 2 3 4 5 6 7 8 T P1 P2 P5 P5 P5 P6 9 10 P3 + ; - 20 CAT (Computer Aided Transceiver) Operation VX VOX STATUS Set 1 2 3 4 5 6 7 8 9 10 P1 0: VOX “OFF” 1: VOX “ON” V X P1 ; ; Read 1 2 3 4 5 6 7 8 9 10 V X ; Answer 1 2 3 4 5 6 7 8 9 10 V X P1 ; XT TX CLAR Set 1 2 3 4 5 6 7 8 9 10 P1 0: TX CLAR “OFF” 1: TX CLAR “ON” X T P1 ; ; Read 1 2 3 4 5 6 7 8 9 10 X T ; Answer 1 2 3 4 5 6 7 8 9 10 X T P1 ; ZI ZERO IN Set 1 2 3 4 5 6 7 8 9 10 (CW AUTO ZERO IN Function) Z I ; ; Read 1 2 3 4 5 6 7 8 9 10 Answer 1 2 3 4 5 6 7 8 9 10 21 Copyright 2019 YAESU MUSEN CO., LTD. All rights reserved. No portion of this manual may be reproduced without the permission of YAESU MUSEN CO., LTD. YAESU MUSEN CO., LTD. Tennozu Parkside Building 2-5-8 Higashi-Shinagawa, Shinagawa-ku, Tokyo 140-0002 Japan YAESU USA 6125 Phyllis Drive, Cypress, CA 90630, U.S.A. YAESU UK Unit 12, Sun Valley Business Park, Winnall Close Winchester, Hampshire, SO23 0LB, U.K. 1904-A

FREE ENGLISH PDF

OPERATING INSTRUCTIONS

USER GUIDE - USER MANUAL

OWNER GUIDE - OWNER MANUAL

REFERENCE GUIDE - REFERENCE MANUAL

INSTRUCTION GUIDE - INSTRUCTION MANUAL