YAMAHA PSR-S910 (02) PDF MANUAL

Report any errors on this page in the comment box below.

PDF OCR Transcript: Version 1.10 Upgrade Manual Version 1.10 of the firmware adds the following functionality to PSR-S910 and PSR-S710 models. • Support for the Wi-Fi Protected Access (WPA) wireless encryption standard (with the exception of certain USB-LAN adaptors1) • Support for the Wi-Fi Protected Setup (WPS)2 standard, which makes it easier to setup wireless home networks (with the exception of certain USB-LAN adaptors1) • Support for the following USB-LAN adaptors. Wireless: Buffalo WLI-UC-GN Buffalo WLI-UC-GNHP Planex GW-USMicroN Planex GW-USMini2N Edimax EW-7711UAn Edimax EW-7711UTn Hawking HWUN3 Tenda W311U Belkin F6D4050 LogiLink WL0049A LogiLink WL0054 Wired: LINKSYS USB300M AIRLINK101 ASOHOUSB 10/100Mbps Fast Ethernet USB 2.0 Adapter macally AIR2NET INTELLINET Hi-Speed USB 2.0 to Fast Ethernet Adapter 1: For more details, please visit the Yamaha Piano / Keyboard website (below) and refer to the list of USB devices confirmed as working with our products. http://music.yamaha.com/download *2: For more details, please refer to the Internet Connection Guide, which can be downloaded from the Yamaha Manual Library website. http://www.yamaha.co.jp/manual/english/

  1. Turn on the PSR-S910/S710. This can be done by pressing the [STANDBY/ON] switch located at the left of the front panel.
  2. Confirm the instrument’s current firmware version as follows. 2-1 Press the [FUNCTION] button. 2-2 Press the [J] (UTILITY) button. 2-3 Using the TAB [E] / [F] buttons, select the OWNER tab and display the Owner setting screen. 2-4 Press the [7▲] (VERSION) button to display the current firmware version. If the displayed version number is less than 1.10, the firmware should be upgraded. Confirming the Current Version 2-5 Press the [8▲] (EXIT) button or the [EXIT] button to close the window.
  3. Turn off the PSR-S910/S710. This can be done by pressing the [STANDBY/ON] switch located at the left of the front panel. To upgrade the firmware, place the upgrade data on a USB flash memory device and then carry out the upgrading procedure as described below.
  4. Plug the USB flash memory device containing the upgrade data into the PSR-S910/S710.
  5. Hold down the [START/STOP] button and press the [STANDBY/ON] switch. Continue to hold down the [START/STOP] button until the following message is displayed.
  6. Install the upgrade data. To do so, release the [START/STOP] button and then press it once again. DIGITAL WORKSTATION / Upgrading the Firmware 1

After indicating that data is being loaded, the PSR-S910/S710 will begin to install the new version of the firmware. The following message is displayed at this time. Upgrading of the firmware takes approximately 5 minutes. The USB flash memory device must not be unplugged and the instrument must not be turned off while the firmware is being installed. Failure to observe this precaution may render the PSR-S910/S710 unfit for use. The following message is displayed upon completion of the firmware installation process.

  1. Turn off the PSR-S910/S710 and unplug the USB flash memory device. Reconfirming the Current Version After any firmware upgrade, it is recommended that you confirm the current version once again as described below. 1. Turn on the PSR-S910/S710. This can be done by pressing the [STANDBY/ON] switch located at the left of the front panel. 2. Confirm the instrument’s current firmware version as follows. 2-1 Press the [FUNCTION] button. 2-2 Press the [J] (UTILITY) button. 2-3 Using the TAB [E] / [F] buttons, select the OWNER tab and display the Owner setting screen. 2-4 Press the [7▲] (VERSION) button to display the current firmware version. If the upgrade process has been completed successfully, version 1.10 will be shown in the window displayed. If the version has not changed, it is likely that the installation procedure was not completed successfully. In such a case, repeat the procedure carefully as described herein.
  2. Press the [8▲] (EXIT) button or the [EXIT] button to close the window. Deleting Upgrade Data Deletion using the instrument: Version 1.10 of the firmware for PSR-S910 and PSR-S710 models makes it possible to delete upgrade data from a USB flash memory device using the instrument itself. To do so, proceed as follows.
  3. Plug the USB flash memory device containing the upgrade data into the PSR-S910/S710.
  4. Hold down the [START/STOP] button and press the [STANDBY/ON] switch. Continue to hold down the [START/STOP] button until the following message is displayed.
  5. Press the [BREAK] button to delete the upgrade data. The following confirmation message will be displayed.
  6. To delete the upgrade data, release the [START/ STOP] button and then press it once again. The PSR-S910/S710 will begin deleting the upgrade data. The following message is displayed at this time. The USB flash memory device must not be unplugged and the instrument must not be turned off while the upgrade data is being deleted. Failure to observe this precaution may result in the USB flash memory device being permanently damaged. The following message is displayed upon completion of the data deletion process.
  7. Turn off the PSR-S910/S710 and unplug the USB flash memory device. This can be done by pressing the [STANDBY/ON] switch located at the left of the front panel.

The USB flash memory device must not be unplugged and the instrument must not be turned off at this time. Failure to observe this precaution may render the PSR-S910/S710 unfit for use. 2

FREE ENGLISH PDF

OPERATING INSTRUCTIONS

USER GUIDE - USER MANUAL

OWNER GUIDE - OWNER MANUAL

REFERENCE GUIDE - REFERENCE MANUAL

INSTRUCTION GUIDE - INSTRUCTION MANUAL